Structural Engineering and Mechanics

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Simplified design formula of slender concrete filled steel tubular beam-columns

  • Chung, Jinan (Department of Architecture, Fukuoka University) ;
  • Matsui, Chiaki (Department of Human-Environment Studies, Kyushu University) ;
  • Tsuda, Keigo (Department of Human-Environment Studies, Kyushu University)
  • Published : 2001.07.25
⟨ Previous Next ⟩

Abstract

The objective of this paper is to develop a simplified method that could predict the strength of concrete filled steel tube (CFT) columns applicable to high strength material under combined axial compression and flexure. The simplified method for determining the strength of CFT columns is based on the interaction curve of the section approached by a polygonal connection of the points. These points are determined by using symmetrical properties of the CFT section. For each point, a simple equation is proposed to determine the strength of the slender columns under compression and flexure. The simple equation was adjusted with results of elasto-plastic analysis results. Validation of the simplified method is undertaken by comparison with data from the test conducted at Kyushu University. These results confirm the fact that the simplified method could accurately and reliably predict the strength of CFT columns under combined axial compression and flexure.

Keywords

References

  1. American Institute of Steel Construction (1993), Load and Resistance Factor Design Specification for StructuralSteel Buildings.
  2. American Concrete Institute (1995), Building Code Requirements for Reinforced Concrete and Commentary, ACI318-95.
  3. Architectural Institute of Japan (1987), Standards for Structural Calculation of Steel Reinforcement ConcreteStructures, 4th edn.
  4. Architectural Institute of Japan (1997), Recommendations for Design and Construction of Concrete Filled SteelTubular Structures.
  5. Chapman, J.C., and Neogi, P.K. (1966), "Research on concrete filled tubular columns", Engineering StructuresLaboratory Reports, Civil Engineering Department, Imperial College, May.
  6. Chung, J., Tsuda, K., and Matsui, C. (1999), "High-strength concrete filled square tube columns subjected toaxial loading", The 7th East Asia-Pacific Conf. on Struct. Eng. & Const., Japan, 2, August, 955-960.
  7. Chung, J., Tsuda, K., and Matsui, C. (1999), "Slender square tube columns filled with high-strength concrete",The First Int. Conf. on Advances in Struct. Eng. and Mech., Korea, August, 2.
  8. Chen, W.F., and Atsuta, T. (1972), "Simple interaction equations for beam-columns", J. Struct. Div., ASCE,98(ST7), Proc. Paper 9020, July, 1413-1426.
  9. Chen, W.F., and Atsuta (1973), "Theory of beam-columns", McGraw-Hill, Inc.
  10. European Committee for Standardization (1994), Design of Composite Steel and Concrete Structure, Brussels, Belgium.
  11. Fang, T., and Nakamura, T. (1994), "An experimental study on compression strength of concrete filled squaretubular steel columns", J. Struct. Eng., 40B, March, 411-417.
  12. Fuji, K., Kotera, C., and Yamoto, H. (1994), "Experiments on buckling strength of mortar filled steel tubularcolumns of two types", J. of Steel Const. Eng., Jun, 47-56.
  13. Furlong, R.W. (1974), "Concrete encased steel beam columns (Design Tables)", ASCE, 100(ST8), 1865-1883.
  14. Gardner, N.J., and Jacobsen, E.R. (1967), "Structural behavior of concrete filled steel tubes", Proceedings, ACI,64(11).
  15. Guiaux, P., and Janss, J. (1970), "Comportement au flambement de colonnes constituées de tubes en acierremplis de béton", C.R.I.F. Rapport, MT65, Bruxlelles.
  16. Klöppel, K., and Goder, D. (1957), "Traglastversuche mit ausbetonnierten Stahlrohren und Aufstellung einerBemessungsformel", Der Stahlbau, Heft 1 und 2.
  17. Knowles, R,B. and Park, R. (1970), "Axial load design for concrete filled steel tubes", J. Struct. Div., Proc. ofthe American Society of Civil Engineers, 96(ST10), 2125-2153.
  18. Masuo, K., Mikio, A., Yasuhiro, Y., and Masaki, K. (1992), "Buckling behavior of concrete filled circular steeltubular columns using light-weight concrete", J. Struct. Eng., 38B, March, 349-360.
  19. Roik, K., Bode, H., and Bergmann, R. (1982), "Zur Traglast von betongefüllten Hohlprofilstützen unterBerücksichtigung des Langzeitverhaltens des Betons", Der Stahlbau 51 Heft 7.
  20. Sasaki, L. (1984), "Experimental study on buckling strength of composite columns having steel tube",Summaries of Technical papers of Annual Meeting, Architectural Institute of Japan, 2735-2736.
  21. Sen, H.K (1972), "Concrete filled tubular steel columns", Tubular Structures 17, Tubes Division of British SteelCorporation, November.
  22. Tsuda, K., Matsui, C., and Ishibashi, Y. (1995), "Stability design of slender concrete filled steel tubular column",Proc. of the Fifth Asia-Pacific Conf. on Struct. Eng. and Constr. (EASEC-5), Gold Coast, Australia, July.
  23. Wakabayashi, M. (1977), "A new design method of long composite beam-columns", Proc. of Int. Colloquium onStability of Structures under Static and Dynamic Load, SSRC/ASCE Washington D.C, 742-756.

Cited by

  1. CONCRETE-FILLED TUBULAR COLUMNS: PART 1 — CROSS-SECTION ANALYSIS vol.04, pp.04, 2004, https://doi.org/10.1142/S021945540400132X
  2. Damage Assessment of Rectangular Concrete-Filled Steel Tubes for Performance-Based Design vol.20, pp.4, 2004, https://doi.org/10.1193/1.1809660
  3. LOAD-BEARING CAPACITY OF CONCRETE-FILLED STEEL COLUMNS vol.15, pp.1, 2001, https://doi.org/10.3846/1392-3730.2009.15.21-33
  4. BUCKLING OF SLENDER COMPOSITE CONCRETE‐FILLED STEEL COLUMNS vol.16, pp.2, 2010, https://doi.org/10.3846/jcem.2010.26
  5. Evaluation of the ultimate eccentric load of rectangular CFSTs using advanced neural network modeling vol.248, pp.None, 2001, https://doi.org/10.1016/j.engstruct.2021.113297