Detectibility of Internal Defects in Aluminum Die-casted Rotor Using Ultrasonic Technique

초음파를 이용한 알루미늄 다이캐스팅 회전자 내부 결함 검출능 평가에 관한 연구

  • Published : 2001.12.01

Abstract

The aluminum die-casting technique has been widely used to manufacture a rotor in motor industry because of its highly productivity, even though it sometime causes the various type of defects in the rotor, such as shrinkage, cavity, blow holes etc. which results in the decrease of the efficiency of system. Therefore the development of reliable technique to detect the flaws in the rotor is strongly needed not only to control quality assurance but to improve its efficiency. In this study, the wide variety of ultrasonic techniques have been applied to detect the flaws in the rotor and then to discuss the detectibility of the flaw and the applicability for NDE tool in the aluminum die-casting rotor.

Keywords

References

  1. Austin H. Bonnett, 'Cause and Analysis of Stator and Rotor Failures in Three-Phase Squirrel-cage Induction Motors', IEEE Transactions on Industry Applications, vol.28, no.4, pp.921-937, 1992 https://doi.org/10.1109/28.148460
  2. Austin H.Bonnett, 'Analysis of Rotor Failure in Squirrel-Cage Induction motors', IEEE Transactions on Industry Applications, Vol.24, No.6, pp.1124-1130, 1988 https://doi.org/10.1109/28.17488
  3. 포항공과대학교, '다이캐스팅 알루미늄 용해기술개발', 고효율 유도전동기 개발사업 중간발표회 초록집 II, pp.191-203 1995
  4. 포항공과대학교, '다이캐스팅 알루미늄 용해 기술개발', 고효율 유도전동기 개발사업 중간발표회 초록집 III, pp.85-99, 1996
  5. Lee, J. H., Choi, S. W., Lee, M. R., Park, M. J., 'Application of Novel Hall Sensor Technique to Evaluate Internal Defect in Squirrel Cage Rotor,' Review of Progress in Quantitative NDE,' pp.63, 2000
  6. Lee, J.H., Choi, S.W., Park, M.J., 'Evaluation of Internal Defects in Squirrel Cage Rotor by Novel Hall Sensor Technique,' 2001 IEEE International Symposium on Industrial Electronics (ISIE2001) Proceeding, pp.1929-1933, 2001 https://doi.org/10.1109/ISIE.2001.932007
  7. 이준현, 최상우, '저면산란 초음파 신호 및 신경회로망을 이용한 균열크기 결정', 대한기계학회논문집 A, 제24권 제1호, pp.52-61, 2000
  8. 최상우, 이준현, '초음파 판파와 신경회로망을 이용한 리벳홀 부위 균열 크기 평가,' 한국비파괴검사학회 '98 춘계학술발표회 논문집, pp.117-127, 1998
  9. 장경영, 장효성, 박병일, '초음파주사 현미경의 분해능 향상을 위한 중첩된 펄스에코 신호의 분리기법(디컨볼루션과 웨이브렛 변환의 혼합기법),' 한국정밀공학회지, 제17권 제7호, pp.217-225, 2000
  10. S. Birks, R. E. Green, Jr. Ultrasonic testing, Nondestructive testing handbook., Vol.7, 1991