대한소아치과학회지 (Journal of the korean academy of Pediatric Dentistry)
- 제24권2호
- /
- Pages.460-474
- /
- 1997
- /
- 1226-8496(pISSN)
- /
- 2288-3819(eISSN)
Low-viscosity Resin Sysem이 복합레진 수복물의 변연누출에 미치는 영향
THE EFFECT OF LOW-VISCOSITY RESIN SYSTEMS OM MARGINAL LEAKAGE OF COMPOSITE RESIN RESTORATIONS
- 양정숙 (전북대학교 치과대학 소아치과학교실 및 치의학연구소) ;
- 김문현 (전북대학교 치과대학 소아치과학교실 및 치의학연구소) ;
- 허선 (전북대학교 치과대학 소아치과학교실 및 치의학연구소) ;
-
김재곤
(전북대학교 치과대학 소아치과학교실 및 치의학연구소) ;
- 백병주 (전북대학교 치과대학 소아치과학교실 및 치의학연구소)
- Yang, Jeong-Suk (Dept. of Pediatric Dentistry and Institute of Dental Science, School of Dentistry, Chonbuk National University) ;
- Kim, Mun-Hyoun (Dept. of Pediatric Dentistry and Institute of Dental Science, School of Dentistry, Chonbuk National University) ;
- Her, Sun (Dept. of Pediatric Dentistry and Institute of Dental Science, School of Dentistry, Chonbuk National University) ;
-
Kim, Jae-Gon
(Dept. of Pediatric Dentistry and Institute of Dental Science, School of Dentistry, Chonbuk National University) ;
- Baik, Byeong-Ju (Dept. of Pediatric Dentistry and Institute of Dental Science, School of Dentistry, Chonbuk National University)
- 발행 : 1997.05.31
초록
The purpose of this study was to evaluate and compare the effectiveness of various low-viscosity resin systems used as rebonding agents to prevent microleakage at the margins of class I composite resin restorations. Seventy sound human premolars were selected for experiment. Class I cavities were prepared and each cavity was conditioned with a 37% phosphoric acid for 15 sec, rinsed with water for 15 sec, and dried with compressed air. Bonding agent(Scotchbond Multipurpose, 3M Co.) was applied and a hybrid composite resin (Z-100, 3M Co.) was placed using an incremental technic. The excess cured composite resin was carefully removed with Sof-Lex discs(3M Co.) to expose the original margins of the cavity. The following seven groups were established : group 1 was not rebonded and used as control group ; group 2 was rebonded with a Scotchbond Multipurpose(3M Co.) and finished ; group 3 was rebonded with a Fortify(BISCO) and finished ; group 4 was rebonded with a Concise white sealant(3M Co.) and finished ; group 5 was rebonded with a Concise white sealant(3M Co.) and not finished ; group 6 was rebonded with a P&F sealant(BISCO) and finished; group 7 was rebonded with a P&F sealant(BISCO) and not finished. The specimens were then subjected to 500 thermocycles between 5 & 65 with a 10 see dwell time and immersed in 2% methylene blue dye solution for 24 hours and sectioned with low-speed diamond cutter into two part under water condition. The extent of microleakage at rebonded margins was evaluated microscopically and scored for dye penetration according to the following scale : 0=no dye penetration ; 1=dye penetration to half-way along axial wall between enamel surface and DEJ ; 2=dye penetration beyond halfway along axial wall between enamel surface and DEJ ; 3=dye penetration to the full depth of DEJ or beyond DEJ. Selected samples were prepared for SEM observation to determine the depth of penetration of the rebonding agent into the marginal interface. The obtained results were as follows: 1. In the group 2 and 3, which is rebonded with a Scotchbond Multipupose and Fortify, dye penetration score were decreased significantly than that of group 1 (P<0.05), but group 4 and 6 were not statistically different from group 1(P>0.05). 2. There were significant differences between group 4, 6 and group 5, 7 when compared by dye penetration score (P<0.05). 3. In the SEM observation, Scotchbond Multipurpose and Fortify were penetrated within
키워드