• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.4 no.3
• /
• pp.252-261
• /
• 1994

The $(Ba_{1-X}Sr_X)ZrO_3$ powder showing chemically pure and fine particle size was attempted to be synthesized by the oxalate method. The objective of this study is to determine the optimum synthesis condition of stable $(Ba_{1-X}Sr_X)ZrO_3$ powder in terms of the temperatures coefficient of resonant frequency ${\tau}_f$ by examining the microstructure and dielectric properties of the synthesized powder. The six compounds (x=0, 0.2, 0.4, 0.6, 0.8, 1) of $(Ba_{1-X}Sr_X)ZrO_3$ were prepared by the oxalate method, and then calcined at $1000^{\circ}C$ to obtain the crystalline $(Ba_{1-X}Sr_X)ZrO_3$ powder. The synthesized powder showed the globular-shape and average particle size of less than $0.2 \mu\textrm{m}$. The composition of x=0.5, i.e., half of Ba was replaced by Sr, is experted to show the zero value of temperatures coefficient of capacitance ${\tau}_c$.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.6
• /
• pp.163-170
• /
• 2012

With the advantage of a rapid exothermic reaction property, jet set concrete may be used as a cold weather concrete because it can reach the required strength before being damaged by cold weathers. And it can be hardened more quickly if the field temperature is properly compensated by heating. Because ordinary concrete cannot be hardened well under sub-zero temperatures, anti-freeze agents are typically added to prevent the frost damage and to ensure the proper hardening of concrete. While the addition of a large amount of anti-freeze agent is effective to prevent concrete from freezing and accelerates cement hydration resulting in shortening the setting time and enhancing the initial strength, it induces problems in long-term strength growth. Also, it is not economically feasible because most anti-freeze agents are mainly composed of chlorides. Recent studies reported that magnesia-phosphate composites can be hardened very quickly and hydrated even in low temperatures, which can be used as an alternative of cold weather concrete for cold weathers and very cold places. As a preliminary study, to obtain the material properties, mortar specimens with different mixture proportions of magnesia-phosphate composites were manufactured and series of experiments were conducted varying the curing temperature. From the experimental results, an appropriate mixture design for cold weathers and very cold places is suggested.

• Korean Journal of Food Science and Technology
• /
• v.21 no.6
• /
• pp.742-748
• /
• 1989

Rheological properties of gelatinized millet starch dispersions were evaluated. Gelatinized nonwaxy and waxy millet starch dispersion were typical pseudoplastic fluids. At constant shear rate, gelatinized waxy millet starch dispersion showed higher shear stress than nonwaxy millet starch dispersion. Flow behaviours of gelatinized nonwaxy and waxy millet starch dispersion were well fitted to Herschel-Bulkley equation and flow behaviour index (n) and consistency index (K) were strongly concentration dependent. There was a linear relationship between concentration of gelatinized starch dispersion and square root of yield stress. The concentrations of gelatinized nonwaxy and waxy millet starch dispersion where yield stresses become zero were estimated as 2.19 and 1.69%, respectively. Pseudoplastic constant (m) approaches to a constant value in each type of millet starch when the concentration of gelatinized starch dispersion was increased. As the measuring temperatures increase, n value was increased, whereas, K value was decreased. The activation energies of gelatinized nonwaxy and waxy millet starch dispersion were 2.89 and 3.18kcal/mol, respectively.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.16 no.2
• /
• pp.237-244
• /
• 1992

The purpose of this study was to comparatively evaluate thermal and water transmission properties of several vapor permeable water repellent (VPWR) fabrics and synthetic battings that became available in recent years. Five VPWR fabrics evaluated were Hipora in three coating variants, $Gore-Tex^{\circledR}$ and $Aitace^{\circledR}$. Battings evaluated were $Viwarma^{\circledR}$, $Uniwarmr^{\circledR}$, $Thinsulate^{\circledR}$, and $Airseal^{\circledR}$ Thermal resistance and water vapor transmission were measured for each fabric and batting and in all combinations. Thermal resistance at zero and 37 cm/sec air velocity was determined by the Thermo Labo II technique for simultaneously measuring conduction and radiation heat transfer. Water vapor transmission over 24 hours was measured by a modified weight-gain method in a compact humid chamber at conditions simulating the clothing climate under heavy exercise ($40{\pm}1^{\circ}C$, $90{\pm}2\%$ R.H., and 0.5 m/sec air velocity). Fabric porosity was calculated from fiber density and fabric weight, thickness, and area. Thermal resistance results for the fabrics showed the effectiveness of coatings in inhibiting heat transfer. Measurements taken in wind were: $31.1\~37.6\%$ for $Hipora^{\circledR}$ variants; $31.0\%$ for $Gore-Tex^{\circledR}$; and $18.4\%$ for $Aitaca^{\circledR}$ Measurements without wind were higher but in the same order. Water vapor transmission results were in reverse order: $Aitac^{\circledR}$, $8.8 kg/m^{2};\;Gore-Tex^{\circledR}$, 6.4 kg/$m^{2}$; and $Hipora^{\circledR},\;4.4\~6.0\;kg/m^{2}$. In general thermal resistance increased with porosity. For battings, the thermal resistance with wind results were: $Viwarmu^{\circledR}$, $65.0\%;\; Thinsulate^{\circledR}$, $62.0\%$; $Uniwarm^{\circledR}$, $61.0\%$; and $Airseala^{\circledR},\;53.1\%$. Thermal resistance was proportional to thickness. Thermal resistance of fabric-batting combinations were $20\%$ higher than those of the battings only. Water vapor transmission for combinations was mainly affected by that for the VPWR fabric used.

• Journal of the Korean GEO-environmental Society
• /
• v.14 no.5
• /
• pp.33-39
• /
• 2013

A drilling exploration in deep sea is being processed to develop new energy resource in the world. In 2007, the presence of the gas hydrate had been confirmed during the UBGH1 (Ulleung Basin Gas Hydrate Expedition 1) in the Ulleung Basin. Geotechnical properties of the deep marine sediment are important factors for assessing the safety of gas production facility and productivity from the hydrate bearing sediment. In this study, comprehensive laboratory tests are conducted to investigate the geotechnical engineering characteristics of the deep marine sediments recovered from the hydrate occurrence regions during the UBGH2 (Ulleung Basin Gas Hydrate Expedition 2) in the Ulleung Basin, East Sea, Korea. The index properties of the specimens including the specific gravity, atterberg limits, specific surface, and particle size distribution are measured, and these are compared to the results reported by previous studies. A zero-lateral strain cell, which houses bender elements, is used to determine stress-dependant characteristics and shear wave velocities with the vertical effective stresses. Furthermore, the hydraulic conductivity is calculated based on the consolidation test results.

• Elastomers and Composites
• /
• v.37 no.2
• /
• pp.79-85
• /
• 2002

Ethyl-branched polyethylene [PE(2)] containing 2mole% ethyl branch and three ethylene-propylene rubbers (EPR's) having the same ethylene(E)-propylene(P) molar ratio(E/P=50/50) with different stereoregularity, that is, random EPR (r-EPR), alternating-EPR (alt-EPR) and isotactic-alternating-EPR (iso-alt-EPR) were mixed for the investigation or their properties depending on the stereoregularity. Crystallinity of the prepared blends decreased with increasing content of amorphous EPR because of a decrease in both the degree of annealing and kinetics of diffusion of the crystallizable polymer content. With blend composition, crystallinity was reduced with the stereoregularity in EPR. The thermodynamic interaction parameter(x) for the three blend systems approximately equals to zero near the melting point. These systems were determined to be miscible on a molecular scale near or above the crystalline melting point or the crystalline PE(2). From the measurement of $T_m$ vs. $T_c$, the behavior of PE(2) is mainly due to a diluent effect of EPR component. The spherulite size measured by small angle light scattering (SALS) technique depended upon blend composition, and stereoregularity of EPR. The size of spherulite was enlarged with the content of rubbery EPR and the decrease of stereoregularity in EPR.

• Journal of the Korean Ceramic Society
• /
• v.40 no.9
• /
• pp.842-848
• /
• 2003

Semiconducting $\alpha$-Fe$_2$O$_3$ film was prepared by the cathodic electrodeposition method on Indium Tin Oxide (ITO) substrate for photoelectrochemical cell application. After heat treatment at 50$0^{\circ}C$, the phase was changed from Fe to $\alpha$-Fe$_2$O$_3$. The phase, morphology, absorbance, and photocurrent density (A/$\textrm{cm}^2$) of the film depended on the preparation conditions: deposition time, applied voltage, and the duration of heat treatment. The $\alpha$-Fe$_2$O$_3$ film was characterized by X-Ray Diffractometer (XRD), Scanning Electron Microscope (SEM), and UV -Visible Spectrophotometer. The stability of the $\alpha$-Fe$_2$O$_3$ film in aqueous solution was tested at zero bias potential under the white-light source of 100 mW/$\textrm{cm}^2$. The apparent grain size of the films formed at -2.0 V was larger than that grown at -2.5 V. The $\alpha$-Fe$_2$O$_3$ film deposited at -2.0 V for 180 s and heat-treated at 50$0^{\circ}C$ for 1 h showed the predominant photocurrent of 834$\mu$A/$\textrm{cm}^2$.

• Economic and Environmental Geology
• /
• v.42 no.1
• /
• pp.73-84
• /
• 2009

The stone Buddha and Shrine of Unjusa temple (Korean Treasure No. 797) at Hwasun formed in Koryo Dynasty is unique style which faces each other the back parts of south and north within the stone Shrine. The stone Buddha and Shrine is highly evaluated in historical, artistic and academic respects. But, the stone properties have been exposed in the open system various aspects of degradations weathered for a long time without specific protective facilities. To inquire into relative deterioration and environmental factor, air temperature and relative humidity of the stone Buddha and Shrine were monitored for a year of the indoor and outdoor, respectively. As a result, the temperature shows increase and decrease according to the seasons in the tendency to clear. While the relative humidity is high to keep all four seasons. Highly relative humidity environment induces dew condensation on the interior of stone Buddha and Shrine. The dew condensation is recorded at the spring, summer and winter season. The summer season is double the total of spring and winter season. In the case of summer, dew condensation is long time continued due to high temperature and relative humidity that is kept by more than nearly 100%. There is progress towards chemical weathering throughout dissolve rock properties and alteration on the rock surface. In the case of winter, dew condensation is not kept for a long time as summer. In the winter, which showing a below zero may add physical weathering throughout moisture that happen by dew condensation to repeat freezing and thawing. Therefore, the reduction plan of the relative humidity effect on dew condensation should be prepared.

• Journal of Biosystems Engineering
• /
• v.26 no.5
• /
• pp.461-468
• /
• 2001

Impact between fruits and other materials is a major cause of product damage in harvesting and handling systems. The oriental pears are more susceptible to bruising than other fruits such as European pears and apples, and are required more careful handling. The interest in the handling of the pears for the processing systems has raised the question of the allowable drop height to which pears can be dropped without causing objectionable damage. Drop tests on pears were conducted using an impact device developed by authors to estimate the allowable drop height without bruising. The impact device was constructed to hold in a selected orientation and to release a fruit by vacuum for dropping on to a force transducer. The drop height was adjustable for zero to 60 cm to achieve the desired distance between the bottom of the fruits and the top of the impact force transducer. The transducer was secured to 150 kg$\sub$f/ concrete block. The transducer signal was sampled every 0.17 ms with a strain gage measurement board in the micro computer where it was digitaly stored for later analysis. The selected sample fruit was Niitaka cultivar of pears which is one of the most promising fruit for export in Korea. The pears were harvested during the 1998 harvest season from an orchard in Daejeon. The sample fruit was selected from two groups which were stored for 3 months and 5 months respectively by the method of current commercial practice. The pears were allowed to stabilize at environmental condition(18$^{\circ}C$, 65% rh) of the experimental room. One hundred fifty six pears were tested from the heights of 5, 7.5. 10 and 12.5 cm while measurement were made of impact peak force, contact time, time to peak force, dwell time, pear diameter and mass. The bioyield strength and modulus of elasticity were measured using UTM immediately after each drop test. The allowable drop height was estimated on the base of bioyield strength of the pears in two ways. One was assumed the peak force during impact test increasing linearly with time, and the other was based on the actual drop test results. The computer program was developed for measuring the impact characteristics of the pears and analyzing the data obtained in the study. The peak force increased while contact times decreased with increasing drop height and contact times of the sample from the hard tissue group. The allowable drop height increased with increasing bioyield strength and contact times, and also varied with Poisson\`s ratio, mass and equilibrium radius of the pears. The allowable drop height calculated by a theoretical method was in the range from 1 to 4 cm, meanwhile, the estimated drop height considering the result of the impact test was in the range from 1 to 6 cm. Since the physical properties of fruits affected significantly the allowable drop height, the physical properties of the fruits should be considered when estimating the allowable drop height.

• Journal of the Korean Magnetics Society
• /
• v.8 no.6
• /
• pp.374-379
• /
• 1998

$Mn_1-xCr_xPt_3$ alloy films have been prepared by depositing (Mn, Cr)/Pt multilayers using a rf magnetron sputterer followed by heat treatment. Small and wide angle x-ray diffractometry, magnetic hysteresis loops and Kerr rotation angle spectra of the films have been measured and used to investigate structural, magnetic and magneto-optic properties of the films. The films had a crystal structure of ordered AuCu$_3$ type and the strong preferred orientation of a (111)plane parallel to the film surface. The saturation magnetization of the films was decreased with Cr content reaching almost zero near x=0.58 and then increased for further increasement of Cr content up to x=0.77 over that stayed almost constant. This indicated that Cr atoms were antiferromagnetically coupled with Mn atoms. The magnetic easy axis of MnPt$_3$(x=0) film was parallel to the film surface but those of the films with x$\geq$0.58 increased as Cr content increased reaching about 4 kOe at x=1(CrPt$_3$). The dependence of the Kerr rotation angle on the Cr content was similar to that of the saturation magnetization on the Cr content. The films with x=0.77 and x=1 showed the larger Kerr rotation angle at the wavelengths of near infrared compared to the magneto-optic recording medium, TbFeCo, currently being used.