• 한국세라믹학회지
• /
• 제29권2호
• /
• pp.119-126
• /
• 1992

3 mol% Y2O3-doped ZrO2 powders were prepared by hydrolysis with 0.1, 0.2, 0.3, 0.4, 0.5, 0.6 mol/ιH2O/ethanol into 0.1 mol/ι zirconium and yttrium alkoside/ethanol. Spherical monodispersed yttria-partially stabilized zirconia particles with an average diameter of about 0.5 ${\mu}{\textrm}{m}$ were prepared by hydrolysis with 0.2 mol/ιH2O/ethanol. The as-prepared powder was amorphous and with heating it transformed into cubic up to 80$0^{\circ}C$ and into tetragonal over 100$0^{\circ}C$. 3 mol% Y2O3-doped ZrO2 powders calcined over and up to 80$0^{\circ}C$ were a mixture of tetragonal and monoclinic and only tetragonal as determined by X-ray diffraction, respectively.

• 한국세라믹학회지
• /
• 제38권3호
• /
• pp.218-224
• /
• 2001

Yttria-stabilized zirconia (YSZ) films were deposited with varying temperatures of ZrCl$_4$between 250~55$0^{\circ}C$ with YCl$_3$and the substrate at 100$0^{\circ}C$. Nanoamperes per square centimeter of the electric current were measured in the reactor during deposition and the current increased with increasing evaporation temperature of ZrCl$_4$. The zirconia nanometer size clusters were captured on the grid membrane near the substrate during the CVD process and observed by transmission electron microscopy (TEM). The deposition rate decreased with increasing evaporation temperature of ZrCl$_4$. A cauliflower-shaped structure was developed at 25$0^{\circ}C$ then gradually changed to a faceted-grain structure above 35$0^{\circ}C$. Dependence of the growth rate and the morphological evolution on the evaporation temperature of ZrCl$_4$was approached by the charged cluster model.

• 한국세라믹학회지
• /
• 제31권9호
• /
• pp.969-974
• /
• 1994

After adding 8Y-ZrO2 powders to 3Y-ZrO2 powders at ratios of 0, 33, 50, 67, and 100% by weight, the mixed yttria-stabilized zirconia specimens were fabricated into thin plate using tape~casting method and then sintered at 150$0^{\circ}C$ for 4h in air. The crystalline structure, microstructure and electrical properties of the sintered zirconia thin plates were investigated by using X-ray diffractometer, scanning electron microscope and impedance analyser, respectively. At the temperatures higher than 75$0^{\circ}C$, the sintered thin plate with 33% 8Y-ZrO2 content shows higher mechanical properties and lower electrical resistivity than 8Y-ZrO2 thin plate which is generally used as an electrolyte for solid oxide fuel cells. This is due to the fact that the zirconia thin plates with low 8Y-ZrO2 content maintain the slope of low temperature region up to high temperatures, whereas at temperatures higher than 50$0^{\circ}C$ the slope decrease in the zirconia thin plates with high 8Y-ZrO2 content.

• 한국세라믹학회지
• /
• 제54권5호
• /
• pp.413-421
• /
• 2017

In this work, we studied a fluorite structure oxides: Yttria stabilized zirconia, (YSZ); Gd doped $CeO_2$ (GDC); erbia stabilized $Bi_2O_3$ (ESB); Zr doped erbia stabilized $Bi_2O_3$ (ZESB); Ca doped erbia stabilized $Bi_2O_3$ (CESB) in the temperature range of 250 to $600^{\circ}C$ using electrochemical impedance spectroscopy (EIS). As is well known, grain boundary blocking effect was observed in YSZ and GDC. However, there is no grain boundary effect on ESB, ZESB, and CESB. The Nyquist plots of these materials exhibit a single arc at low temperature. This means that there is no space charge effect on ${\delta}-Bi_2O_3$. In addition, impedance data were analyzed by using the brick layer model. We indirectly demonstrate that grain boundary ionic conductivity is similar to or even higher than bulk ionic conductivity on cubic bismuth oxide.

• 한국세라믹학회지
• /
• 제29권11호
• /
• pp.851-854
• /
• 1992

It was grown ZrO2:10 mol% Y2O3 single crystals doped with 1 wt% of rare earth metal ion (Ce, Pr, Nd, Er, Eu) by Skull Method. Grown crystals showed Ce:orange-red, Pr:golden-yellow, Nd:lilac, Er:pink, Eu:light pink due to dopant effect. It was examined color centers in light absorption pattern of visible region (λ= 300~700 nm); in as grown samples, absorption by Ce4+, (Pr4+, Pr3+), Nd3+, Er3+, Eu3+ ions were important, and in samples after vacuum annealing, decrease of absorption by Pr4+ ion and increase of absorption by Pr3+ ion was important, and absorption by Ce3+, Eu2+ was important due to reduction of activator.

• 한국재료학회지
• /
• 제9권3호
• /
• pp.234-239
• /
• 1999

PECVD(Plasma enhanced chemical vapor deposition)을 이용하여 yttria-stabilized zirconia(YSZ) 박막을 제조하였다. 반응물질로 금속유기화합물을 $Zr[TMHD]_4$와 $Y[TMHD]_3$그리고 산소를 사용하였으며, 증착온도는 $425^{\circ}C$, rf power는 0~100W까지 적용하였다. YSZ 박막은 (200)면이 기판에 평행한 입벙정상 구조를 가졌으며, 1시간 내에 $1\mu\textrm{m}$ 두께를 형성하였다. EDX에 의한 막의 성분분석 결과로부터 환산된 박막내의 $Y_2O_3$의 함량은 0-36%의 범위였다. 버블러의 온도 및 운반기체의 유량이 증가함에 따라 박막의 두께 역시 비례하여 증가하였는데, 이는 precursor의 flux 증가로 인한 박막내의 $Y_2O_3$의 함량증가에 의한 것이었다. Zr 및 Y, O는 박막의 두께에 따라 일정한 조성비를 나타내었다. 운반기체를 Ar로 하였을 때 $1000\AA$이하의 크기를 갖는 YSZ 입자들이 column 모양으로 기판에 수직하게 성장하였으며, 운반기체가 He인 경우에도 column 모양으로 성장하였으며 입도가 $1000~2000\AA$으로 Ar의 경우보다 조대해졌다. XRD 분석결과 $Y_2O_3$의 함량이 증가함에 따라 YSZ의 격자상수 값이 약간씩 증가하였다. 이는 박막 전반에 걸쳐 형성된 균열에 의해 격자변형으로 인해 발생한 응력을 완화시켰지 때문이다.

• 한국재료학회지
• /
• 제24권7호
• /
• pp.357-362
• /
• 2014

Thermal barrier coatings(TBCs) are being applied in many industrial fields such as thermal power generation, aviation and seasonal fields. $ZrO_2-Y_2O_3$(8%) thermal spray coating powders are commercially used as thermal-barrier coating materials to protect against oxidation and corrosion of heat-resistant alloys at elevated temperatures. Currently, $ZrO_2-Y_2O_3$(8%) thermal-spray powder is made using the industrial co-precipitation process, which is very complex and requires a lot of time. In this study, orthorhombic $ZrO_2$ and $Y_2O_3$ powders were fabricated by mechanical mixing, which is more economical than the co-precipitation process. A tetragonal, yttria-stabilized zirconia(YSZ) coating-layer was produced by plasma spraying, using orthorhombic $ZrO_2-Y_2O_3$(8%) powder. Our experimental results indicate that $ZrO_2-Y_2O_3$(8%) mixed powder can be used economically in industry because it is no longer necessary to make this powder by liquid and gas-phase methods.

• 한국세라믹학회지
• /
• 제24권2호
• /
• pp.123-132
• /
• 1987

Yttria-stabilized zirconia with erbia-lanthana were investigated with respect to the amount of Ln2O3 (Ln; Er, La) addition in the range of 0.5∼5 mol% to the base composition of 8 mol% yttriazirconia. Following analysis and measurement were adopted for the characterization of synthesizes of solid electrolyte; phase transformation, lattice parameter, crystallite size, relative density, chemical composition and SEM/EDS. Electrical conductivity by two-probe method versus temperature from 350$^{\circ}C$ to 800$^{\circ}C$ and frequency in the range of 5Hz∼13MHz by complex impedance method was also conducted together with the determination of oxygen ion transference number by EMF method for the evaluation of their electrical properties. The results were as followsing; Electrical conductivity were decreased with increase in Ln2O3 content, but their activation energies increased. In the case of La2O3 addition, espicially, its electrical conductivity was decreased owing to the segregation of second phases at the grain-boundary. Grain-boundary conductivity of the specimen contained 0.5 mol% Er2O3 exhibited a maximum conductivity among thecompositions experimented. However, their bulk conductivities decreased in both case. Oxygen ion transference number was also reduced with decrease in oxygen partial pressure. For example, in the case of Er2O3 addition it retained value in the range of 0.97∼0.94 abvove 4.74${\times}$10-2in oxygen partial pressure. With the increase in the quantities of the evaporation of additive components, the crystallite size of stabilized zirconia decreased, and their relative density also reduced owing to the formation of porosity in their matrices. In the case of La2O3 the sinterbility was improved in the limited amount of addition up to 0.5 mol%, in the same range of addition the strength of sintered bodies were improved perhaps owing to the precipitation of metastable tetragonal phase in the fully stabilized zirconia.

• 한국세라믹학회지
• /
• 제23권3호
• /
• pp.87-93
• /
• 1986

Yttria-bismuth-stabilized zirconia was investigated with respect to the amount of $Bi_2O_3$ addition in the ran-ge of 0.5~5mol% to the base composition of $(ZrO_2)_{0.92}(Y_2O_3)_{0.08}.Bismuth was introduced into the ma-terial with $Bi_2O_3-SiO_2$ glasses in order to reduce the evaporation of components. The sinterbility evaporation of components phase formation and microstructure were evaluated depending on the amount of $Bi_2O_3-SiO_2$ glass addition. Two probe A. C conductivity measurement was subjected to all the specimens and the result was discussed on the possible substitution of $Bi^{3+}$ for $Zr^{4+}$ and interistial $Si^{4+}$ in the fluorite structure of zirconia crystal there-upon the possible change in the capability of oxygen transference within the material. It was found that the addition of $Bi_2O_3$ could improve the sinterbility of material very much while not so much.oxygen sensing material suitable for relative low temperature firing.

• 한국세라믹학회지
• /
• 제31권5호
• /
• pp.477-484
• /
• 1994

The yttria stabilized zirconia(YSZ) thin films for solid oxide fuel cell (SOFC) were fabricated by an electrochemical vapor deposition(EVD) technique using YCl3+ZrCl4+H2O gas system. The YSZ films were deposited under reduced pressure at the temperature of 1000~120$0^{\circ}C$ on the porous alumina substrates. The deposition rate, chemical composition and growth morphology were investigated by SEM, XRD, EDS. The growth rates of the films obeyed a parabolic rate law, representing that the growing process is controlled by an electrochemical transport through the YSZ film. The Y2O3 content of the films was about 10 mol%, equal to the composition of metal chloride reactant gases, approximately. The YSZ films were highly dense, the growing features showed columnar structure and surface morphologies were changed with the EVD conditions.