• Structural Engineering and Mechanics
• /
• v.40 no.1
• /
• pp.29-48
• /
• 2011

Under large storm loads sections of a long pipeline on the seabed can be uplifted. Numerically this loss of contact is extremely difficult to simulate, but accounting for uplift and any subsequent recontact behaviour is a critical component in pipeline on-bottom stability analysis. A simple method numerically accounting for this uplift and reattachment, while utilising efficient force-resultant models, is provided in this paper. While force-resultant models use a plasticity framework to directly relate the resultant forces on a segment of pipe to the corresponding displacement, their historical development has concentrated on precisely modelling increasing capacity with penetration. In this paper, the emphasis is placed on the description of loss of penetration during uplifting, modelled by 'strain-softening' of the force-resultant yield surface. The proposed method employs uplift and reattachment criteria to determine the pipe uplift and recontact. The pipe node is allowed to become free, and therefore, the resistance to the applied hydrodynamic loads to be redistributed along the pipeline. Without these criteria, a localised failure will be produced and the numerical program will terminate due to singular stiffness matrix. The proposed approach is verified with geotechnical centrifuge results. To further demonstrate the practicability of the proposed method, a computational example of a 1245 m long pipeline subjected to a large storm in conditions typical of offshore North-West Australia is discussed.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.5
• /
• pp.467-474
• /
• 2021

A study on optimal shape selection of a mechanical fastening for the repair of crack defect of ROK Air Force F-5 fighter wing was conducted. The crack defect occurred in the spar of the wing, and the technical manual does not specify the repair method. However, ROK Air Force decided to develop a repair technology for this defect in consideration of various logistic conditions. Three repair shapes for the proper repair were devised and the finite element analysis was performed to examine the structural safety of these three connection members. As a result of the structural safety review, two connection members except one were structurally safe with safety margins over zero because the calculated stress values were at or below the yield strength level. Therefore, two connection members were determined to be able to use for repair under the condition that the aircraft operated within the design limit load. The results of this study would be very useful if the same defect occurs in long-term aircraft operated by the ROK Air Force.

• Nuclear Engineering and Technology
• /
• v.54 no.9
• /
• pp.3205-3214
• /
• 2022

The aim of this study is to provide a clear and accessible method to obtain accurate true-stress strain data, and to extend the limited material data beyond the ultimate tensile strength (UTS) for AISI 304L. AISI 304L is used for the outer construction for some types of nuclear transport packages, due to its post-yield ductility and high failure strain. Material data for AISI 304L beyond UTS is limited throughout literature. 3D digital image correlation (DIC) was used during a series of uniaxial tensile experiments. Direct method extracted data such as true strain and instantaneous cross-sectional area throughout testing such that the true stress-strain response of the material up to failure could be created. Post processing of the DIC data has a considerable effect on the accuracy of the true stress-strain data produced. Influence of subset size and smoothing of data was investigated by using finite element analysis to inverse model the force displacement response in order to determine the true stress strain curve. The FE force displacement response was iteratively adapted, using subset size and smoothing of the DIC data. Results were validated by matching the force displacement response for the FE model and the experimental force displacement curve.

• Composites Research
• /
• v.19 no.6
• /
• pp.16-22
• /
• 2006

The puncture properties under various conditions were investigated for the optimum conditions to yield the best properties. Fiber aspect ratio(AR: length of fiber/diameter of fiber), interphase condition and fiber content were considered as variables which impact the puncture force and friction force. The puncture force of short-fiber reinforced rubber increases up to 3.4 times compared to the virgin material. The better interphase condition shows the higher puncture force at given fiber AR and fiber content. The friction force of the matrix and reinforced rubber with a fiber AR below 155 does not exist. The friction force of the reinforced rubber with the good interphase condition and high fiber AR is higher than puncture force of matrix. Overall, it was found that the interphase condition, fiber AR and fiber content have an important effect on the puncture properties.

• Structural Engineering and Mechanics
• /
• v.9 no.4
• /
• pp.365-374
• /
• 2000

The structural behavior of connections between concrete-filled rectangular tubular column (CFRT column) and steel beam has been studied in this paper through sub-assemblage loading tests. It is found that the sub-assemblages exhibit ductile restoring force characteristics under seismic loading. A formula for the prediction of the yield strength of each member in the connection is proposed by using the yield line theory under the assumption of a simple stress transfer mechanism. It is shown that the proposed formula can produce a reasonable prediction while providing a basis for further investigation.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2001.05a
• /
• pp.443-448
• /
• 2001

This paper presents a bond characteristics of high strength steel reinforced concrete members. High strength steel is what yield strength is higher than that of normal strength steel. So, the amount of flexural steel needed in R.C. members can be decreased. In result, it is expected that the workability and structure quality can improve and man power can minimize. For this purpose, specimens were made and tested with experimental parameters, such as concrete strength, steel diameter and yield strength. The result showed that under same tensile force of steel, in case of substituting normal strength steel with high strength steel, maximum bond stress increased and development length didn't almost change. In addition, the governing equation of bond and bond stress verse slip relationship were derived and compared with test values such as maximum bond stress, slip and bond stiffness.

• Journal of Mechanical Science and Technology
• /
• v.17 no.10
• /
• pp.1485-1495
• /
• 2003

We investigate the triboelectrostatic separation of polyvinylchloride (PVC) from mixed plastics in the laboratory scale triboelectrostatic separation system. The flow and electric fields in the precipitator are obtained from the numerical solution of finite volume method. Using these flow and electric fields, we solved the particle motion equation considering the inertia, drag, gravity and electrostatic forces acted on the particles. The particle trajectories are obtained using a Lagrangian method as a function of different important variables such as Reynolds number, Stokes number, electrostatic force, electric charge and electric field distribution, inclined angle of plane electrodes, particle rebounding, particle charge decay rate after impact on the electrode surface, etc., in order to determine the optimal design conditions. The present predicted results for the cumulative yield represent well the experimental ones.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1617-1621
• /
• 2005

In this study, as a basic research to improve braking efficiency of a ventilated disk brake, we carried out a thermal stress analysis. From analysis result, we knew that a maximum mechanical stress by braking pressure and friction force is applicable to 5 percent of yield strength and has no effect on a fatigue life's decrease for brake disk material. While, a maximum thermal stress by frictonal heat is applicable to 43 percent of yield strength and locates on a friction surface. So, we have found that a thermal stress is the primary factor of crack initiation on a friction surface of disk brake

• Agricultural and Biosystems Engineering
• /
• v.1 no.1
• /
• pp.38-42
• /
• 2000

Though the freshness for agricultural products is an important factor related to their quality management, this terminology is being used restrictedly because it is very subjective. In this study, a dimensionless index which had the span of the maximum of 1 through the minimum of 0 was proposed to describe freshness of the product with time-variant quality and was applied to Tsugaru and Fuji apples. First, the compressive properties having the linearity in their change regarding time elapsed after harvest were selected. For Tsugaru apple, bio-yield and rupture forces had high correlation with time while for Fuji, bio-yield and rupture deformations had high correlations. When the slope, or ratio of force to deformation, was considered, the effect of cultivar could be neglected. When the linearly time-variant compressive properties for Tsugaru and Fuji apples were involved in the freshness indices, they described well freshness of apples. Also, the freshness decay constant depicted a characteristic which related to freshness decay rate. Therefore, the freshness index can be utilized to manage the quality during storage and distribution of apples.

• Tribology and Lubricants
• /
• v.16 no.2
• /
• pp.75-83
• /
• 2000

The present paper proposes a new type of an electro-rheological squeeze film damper (ER SFD) of which the damping capacity can be controlled by the application of electric field. The new ER .SFD- is sealed with slotted rings having electrodes at the inside of the constant gap. The ER SFD can provent the problem of electric short which might be occurred in a previous ER SFD. Reynolds lubrication equation for a Newtonian fluid and the end leakage equation for ER fluids are numerically solved to get the pressure distributions and the damping coefficients of the ER SFD. The results show that the damping coefficients greatly increase with increasing the yield shear stress of ER fluid. In addition, the unbalance response analysis of a flexible rotor supported on the new ER SFD implies that the rotor system can be operated with the minimum of rotor amplitude and force transmissibility by controlling the yield shear stress of ER fluids properly.