• Wind and Structures
• /
• v.12 no.2
• /
• pp.89-101
• /
• 2009

The Monte Carlo procedure was used to simulate wind load effects on a light-frame low-rise structure of irregular shape and a main wind force resisting system. Two analytical models were studied: rigid-beam and rigid-plate models. The models assumed that roof diaphragms were rigid beam or rigid plate and shear walls controlled system behavior and failure. The parameters defining wall stiffness, including imperfections, were random and included wall stiffness, wall capacity and yield displacements. The effect of openings was included in the simulation via a set of discrete multipliers with uniform distribution. One and two-story buildings were analyzed and the models can be expanded into multiple-floor structures provided that the assumptions made in this paper are not violated.

• Journal of Aerospace System Engineering
• /
• v.10 no.1
• /
• pp.29-34
• /
• 2016

Flutter wind-tunnel test is an expensive and complicated process. Also, the test model may has discrepancy in the structural characteristics when compared to those of the real model. "Dry Wind-Tunnel" (DWT) is an innovative testing system which consists of the ground vibration test (GVT) hardware system and software which computationally can be operated and feedback in real-time to yield rapidly the unsteady aerodynamic forces. In this paper, we study on the aerodynamic forces of DWT system to feedback in time domain. The aerodynamic forces in the reduced-frequency domain are approximated by Minimum-state approximation. And we present a state-space equation of the aerodynamic forces. With the two simulation model, we compare the results of the flutter analysis.

• International Journal of Precision Engineering and Manufacturing
• /
• v.2 no.4
• /
• pp.47-53
• /
• 2001

This study is to investigate the problem of the SPM(Skin Pass Mil7) system which is a finishing treatment of steel sheet. and to develop a PID control scheme to minimize process instability. An electrohydraulic servo system with conventional proportional controller used to regulate the force on the strip works inadequately to yield very undesirable transient responses at the moments welding parts of the strip conte into and pass through the rolls. Both linearized and nonlinear models of a typical SPM system ware simulated first by using Simulink. Then Ziegler-Nichols ultimate cycling method was used for an initial reference guide to tune PID gains, and further fine tuning was performed to get desirable response. The test result in the plant show that proposed PID control scheme successfully improves the process instability in a SPM system.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.26-29
• /
• 1999

The sectional forming analysis program for analyzing the hydroforming processes of axisymmetric sheet parts was tleveloped. The rigid-viscoplastic FEM formulation based on membrane theory was derived, wh~cta simi~ltaneously solve force equilibrium as well as non-penetration condition. Hill's non-quadratic normal anisotropic yield theory(1979) was used for material behaviour. For describing the liquid pressure iaction, the flexible tool concept was introduced. Isotropic hardening law was also assumed. To verify the \,alidity of the formulation, the stepped cup forming process as well as the hydrostatic bulging test were \imnlated. Simulation results agreed well with Finckenstein and experimental ones.

• Proceedings of the Korea Concrete Institute Conference
• /
• 1997.10a
• /
• pp.575-580
• /
• 1997

This study presents the techniques to manufacture the model concrete and model reinforcement for the 1/5-scale 3-story reinforced concrete frame. The used model concrete has sufficient workability but shows a little lower strength than expected model steel was made of commercial $\phi$3.2mm and $\phi$2.0mm wire by using deforming device and vacuum tube electric furnace. The yield strength can be simulated but it was difficult to simulate the other properties. The load cell was specially manufactured to measure the shear force in the columns of the first story. The carrying frame and the hinge adapter of artificial mass are explained. The special problems in the process of construction of model are also dressed.

• Textile Coloration and Finishing
• /
• v.7 no.2
• /
• pp.1-8
• /
• 1995

Polymer cationic agent was prepared by the initial polymerization of epichlorohydrin followed by amination with diethyl-amine. Cotton fibre treated with the polymer (6∼8% o.w.f.) is highly cationic and exhibit increased substantivity for anionic dyes. The modified substrate could be dyed with direct dyes without salt or a little salt from dye bath. The increased concentration of cationic agents resulted in an increase the colour yield. Futhermore, treated cotton has an electropositive surface charge. Adsorption of direct dye can be attributed to both van der waals force and electrostatic attraction.

• Applied Microscopy
• /
• v.19 no.2
• /
• pp.1-16
• /
• 1989

To investigate the research of the tumor seeker using liposomes with negatively stained. The fine structure and size in liposomes composed of PC, DSPC, DAPC and SM phospholipid were observed. And the yield of vesicle affected with sonication by mechanical force were determined. The results were as follows. 1. The stain of 2% UA are obtained a good resolution from electron microscopic observation to compare the negatively liposomes with PTA, AM and UA solution. 2. The fine structure of liposomes except DAPC, PC and CH alone samples could be observed from EM experiment of liposomes composed of PC, DSPC, DAPC and SM phospholipid. 3. The results of experiment from 10, 20, 40 and 60 times sonication with 30sec, prepared 0.1mM NTA-SM-liposomes were obtained unilamella vesicles from groups of multilamella vesicles of phospholipid. 4. About 50nm diameter liposomes obtained through membration filtration step to prepare homogenized liposomes.

• Tribology and Lubricants
• /
• v.27 no.1
• /
• pp.34-39
• /
• 2011

In this study, finite element analysis of particle-surface collision using 2-dimensional elements was performed to observe the effects of abrasive size and impact angle. The result of the simulation on the change in abrasive size revealed that larger abrasive particle induced larger contact stress due to force transfer through slurry fluid as the particle moved and pushed the fluid. This observation brought an important finding that the slurry fluid could make the workpiece surface soften and then change the mechanical properties of the surface layer such as elastic modulus and yield strength. As for the impact angle, it was found that the contact stress increased with the angle of impact and jumped up at a specific angle. Such result would be attributed to the complex effects of the impact velocity and angle.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1996.10a
• /
• pp.38-47
• /
• 1996

Sectional analysis program for plane strain or axisymmetric geometry of aluminum alloy sheet metals was developed. For modeling the anomalous behavior of aluminum alloy, Barlat's strain rate potential and Hill's 1990 non-quadratic yield theory arranged under the plane stress assumption were employed. 2-D rigid-viscoplastic FEM formulation based on the bending-augmented membrane theory was derived, solving simultaneously force equilibrium as well as non-penetration condition. Isotropic hardening law was also assumed for yielding behavior. To verify the validity and availability of the developed program, 2-D stretch/draw forming process for plane strain geometry and cylindrical cup deep drawing process for axisymmetric geometry were simulated.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.11a
• /
• pp.1044-1047
• /
• 1996

This paper presents durability characteristics of electrorheological(ER) fluids which undergo a reversible phase change depending upon the imposition of electric fields. The field-dependent Bingham properties are subjected to be altered from long time use of the ER fluid. The level of the changed properties depends upon employed device and test conditions. A piston-rod system which has same mechanism as ER dampers is adopted in this study and tested by increasing operation cycle up to 1 million. Bingham properties of initial and us ER fluids are tested and compared. In addition, these ER fluids are applied to ER damper in order to evaluate damping force performance.