• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.42 no.6
• /
• pp.825-836
• /
• 2022

Micropiles can be used to support additional load in extended building structures. However, their use brings about a risk of exceeding the bearing capacity of existing piles. In this study, pre-compression was applied to distribute the load of an existing building to micropiles, and an indoor loading test was performed to confirm the structural applicability of a wedge-type anchorage device designed to improve its capacity. According to the test results, the maximum strain of the anchorage device was 0.63 times that of the yield strain, and the amount of slip generated at the time of anchorage was 0.11 mm, satisfying structural standards. In addition, using MIDAS GTS, a geotechnical finite element analysis software, the effect of the size of the pre-compression, the thickness of the soil layer, and the ground conditions around the tip on the reaction force of the existing piles and micropiles were analyzed. From the numerical analysis, as the size of the pre-compression load increased, the reaction force of the existing pile decreased, resulting in a reduction rate of up to 36 %. In addition, as the soil layer increased by 5 m, the reduction rate decreased by 4 %, and when the ground condition at the tip of the micropile was weathered rock, the reduction rate increased by 14 % compared with that of weathered soil.

• Resources Recycling
• /
• v.31 no.2
• /
• pp.40-48
• /
• 2022

In this study, the effects of solution components were investigated in the recovery of vanadium as ammonium metavanadate from vanadium-ore-salt roasting-water leaching solution. The vanadium-containing solution is strongly alkaline (pH 13), so the pH must be lowered to 9 or less to increase the ammonium metavanadate precipitation efficiency. However, in the process of adjusting the solution pH using sulfuric acid, aluminum ions are co-precipitated, which must be removed first. In this study, aluminum was precipitated in the form of an aluminum-silicate compound using sodium silicate, and the conditions for minimizing vanadium loss in this process were investigated. After aluminum removal, the silicate was precipitated and removed by adjusting the solution pH to 9 or less using sulfuric acid. In this process, the concentration and addition rate of sulfuric acid have a significant influence on the loss of vanadium, and vanadium loss was minimized as much as possible by slowly adding dilute sulfuric acid. Ammonium metavanadate was precipitated using three equivalents of ammonium chloride at room temperature from the aluminum-free, aqueous solution of vanadium following the pH adjustment process. The recovery yield of vanadium in the form of ammonium metavanadate exceeded 81%. After washing the product, vanadium pentoxide with 98.6% purity was obtained following heat treatment at 550 ℃ for 2 hours.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.32 no.1
• /
• pp.112-118
• /
• 1987

This study was carried out to investigate the effects of early planting and polyethylene film (P.E) mulch on early maturing soybean of Korean native cultivar Kyeonggi No. 114 in the Kyeonggi area. It was planted four times at the ten days interval from April I to April 30 in 1985 and 1986. The average soil temperature was 1-5$^{\circ}C$ higher under the polyethylene film mulch condition than the conventional cultural practice condition. Soil moisture content also was higher under P.E mulch condition. Days to emergence was shortened 5-16 days and days to flowering was shortened 3-5 days. The fresh pod yield was increased 12% more at the planting date of April 1 and April 10. Income was increased 70, 83, more at the planting date of April 1 and April 10 under the polyethylene mm mulch conditions.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.33 no.3
• /
• pp.281-286
• /
• 1988

These studies were conducted to find out the polishing methods that improve yield and quality of the polished barley. Four varieties of hulled barley, Dongbori 1. Bunong, Kangbori and Suwon 182 which were produced in Suwon, Korea in 1979, were subjected to this experiment. The polishing machine, manufactured by Satake Co, was used as test mill. Increasing the roller speed of polishing machine causes more polished barley in a unit period. The speed influenced more in length than thickness or width of grain. Therefore the shape of grain became bold type as the speed increased. The optimum roller speed was 1,300rpm in ideal shape of polished barley. The lowest hardness was observed in the husk layer and the hardness was found in the decreasing order of the aleurone, testa, peri carp and the endosperm layer. The thickness of bran layer, weight of 1,000 kernel and hardness of polished barley were greatly different according to barley varieties. Also the length, thickness, width and the ratio of length to width of barley grain were significantly different in barley varieties. The ratio of length to width of the polished barley was 1.59 in Suwon 182, 1.53 in Bunong, 1.51 in Kangbori and 1.26 in Dongbori 1.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.36 no.5
• /
• pp.383-393
• /
• 1991

Lodging of rice plant is the most important damage by unfavourable weather conditions in rice cultivation. High levels of nitrogen application and growing of Japonica rice variety is one factor to increase the lodging damage. Lodging of rice plant decreasing grain yield; 34% at milky. 21% at dough. 20% at yellow stage. decreasing grain Quality. increasing green rice. and increasing labor cost to harvest. To decrease lodging damage. the lodging resistant varieties will be selected and cultural practices such as amount and time of nitrogen application. planting density. water management. and disease and pest control methods have to be study for the short and strong culm. and good rooting system. Also. application methods such amount and time of plant growth regulators and new types of chemicals will be develop for the reducing lodging of rice plant. To decrease the lodging damage in direct seeding cultivation. first identifying the differences of lodging mechanisms between hand transplanting and direct seeding, second establish the suitable direct seeding methods such as seedling establishement. fertilization. and water menagement.

• Journal of Animal Science and Technology
• /
• v.65 no.1
• /
• pp.132-148
• /
• 2023

Ruminants are the main contributors to methane (CH₄), a greenhouse gas emitted by livestock, which leads to global warming. In addition, animals experience heat stress (HS) when exposed to high ambient temperatures. Organic trace minerals are commonly used to prevent the adverse effects of HS in ruminants; however, little is known about the role of these minerals in reducing enteric methane emissions. Hence, this study aimed to investigate the influence of dietary organic trace minerals on rumen fermentation characteristics, enteric methane emissions, and the composition of rumen bacteria and methanogens in heat-stressed dairy steers. Holstein (n=3) and Jersey (n=3) steers were kept separately within a 3×3 Latin square design, and the animals were exposed to HS conditions (Temperature-Humidity Index [THI], 82.79 ± 1.10). For each experiment, the treatments included a Control (Con) consisting of only basal total mixed rations (TMR), National Research Council (NRC) recommended mineral supplementation group (NM; TMR + [Se 0.1 ppm + Zn 30 ppm + Cu 10 ppm]/kg dry matter), and higher concentration of mineral supplementation group (HM; basal TMR + [Se 3.5 ppm + Zn 350 ppm + Cu 28 ppm]/kg dry matter). Higher concentrations of trace mineral supplementation had no influence on methane emissions and rumen bacterial and methanogen communities regardless of breed (p > 0.05). Holstein steers had higher ruminal pH and lower total volatile fatty acid (VFA) concentrations than Jersey steers (p < 0.05). Methane production (g/d) and yield (g/kg dry matter intake) were higher in Jersey steers than in Holstein steers (p < 0.05). The relative abundances of Methanosarcina and Methanobrevibacter olleyae were significantly higher in Holstein steers than in Jersey steers (p < 0.05). Overall, dietary organic trace minerals have no influence on enteric methane emissions in heat-stressed dairy steers; however, breed can influence it through selective alteration of the rumen methanogen community.

• Clean Technology
• /
• v.16 no.1
• /
• pp.51-58
• /
• 2010

Methane was produced from the anaerobic digestion of marine macro-algae. Elemental analysis was first performed to estimate the theoretical methane production of three macro-algae (Undaria pinnatifida, Laminaria japonica, Hizikia fusiformis). Three algae were found to contain C 34 ~ 36%, H 5%, O 37 ~ 43%, N 2 ~ 4%, S 0.4 ~ 0.7%, and ash 14~21%, and the theoretical methane content was in the range of 56 ~ 60%, which can produce 442 ~ 568 mL $CH_4$ per g of volatile solid (VS). Using the biological methane potential (BMP) test, we found that L. japonica resulted in the highest yield of methane (52%). Moreover, various operational conditions, such as algae amount, pH, salinity, particle size, and pre-treatment, were investigated in order to find an optimal condition of anaerobic digestion. At pH 8.0, the autoclaved L. japonica (5g VS/200 mL), when used without washing salt, produced 268.5 mL/g VS which is 65% of the theoretical methane productions. Furthermore, using a CSTR (with the working volume of 7 L out of the total volume of 10 L), we have successfully operated the reactor for 65 days and obtained maximum methane production rate of 1.4 L/day with purity of 70%.

• Journal of IKEEE
• /
• v.27 no.1
• /
• pp.103-108
• /
• 2023

This research was carried out experiments with changing processes and design parameters to optimally design a SiC-based 1200V power MOSFET, and then, essential electrical characteristics were derived. In order to secure the excellence of the trench gate type SiC power MOSFET device to be designed, electrical characteristics were derived by designing it under conditions such as planner gate SiC power MOSFET, and it was compared with the trench gate type SiC power MOSFET device. As a result of the comparative analysis, the on-resistance while maintaining the yield voltage was 1,840mΩ, for planner gate power MOSFET and to 40mΩ for trench gate power MOSFET, respectively, indicating characteristics more than 40 times better. It was judged that excellent results were derived because the temperature resistance directly affects energy efficiency. It is predicted that the devices optimized through this experiment can sufficiently replace the IGBT devices generally used in 1200V class, and that since the SiC devices are wide band gap devices, they will be widely used to apply semiconductors for vehicles using devices with excellent thermal characteristics.

• Journal of Appropriate Technology
• /
• v.5 no.2
• /
• pp.91-96
• /
• 2019

Microalgae do not require much land and make a higher efficient oil production. However, it costs still much higher than other biodiesel resources, such as crops. Sugars charge 80% of culture media when microalgae are massively cultured in the fermenter. This study aims to develop a cost-efficient process for sugar production from Chinese cabbage byproducts. Pre-treatment with 0.25% H₂SO₄ was most effective when chopped cabbage was incubated 50℃/130 rpm for 24 hours. To hydrolyze cabbage cellulose, we used cellulases secreted from Trichoderma. harzianum. T. harzianum was cultured at 28℃/pH 7/130 rpm for five days. Optimal enzymatic activity of cellulase was obtained by incubating at 0.24 FPU/ml/45℃/pH 5/130 rpm for three days. In comparison to other agricultural waste, such as rice straw, green tea leaves, and palm residue, Chinese cabbage produced the highest sugar yield. We found the optimal conditions to produce sugar from Chinese cabbage byproducts as a carbon source to culture biodiesel-producing microalgae. The efficient process developed in this study helps microalgae as a sustainable alternative energy source by cost-down.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1C
• /
• pp.33-42
• /
• 2006

Lots of river embankments or levees in Korea are quite so old and unknown the origin even. The river deposits, moreover, obtainable easily somewhere were used for materials of embankment without any technical considerations such as the influence soil properties and construction methods on embankment stability. It's natural that safety would be threatened if the water level rises due to flood or rainfall when it comes to abnormal weather conditions, especially. From this point of view, enlargement of embankment, irrigation works, etc. are in progress recently at the situation from a reinforcement work. However, taking influence of soil properties and construction methods on embankment stability into account against cracking or piping is still insufficient. Fragmentary design criteria or irrational construction methods are applied rather as the case may be. In this study, therefore, a way to estimate piping and cracking resistance (Sherard, 1953) has been introduced and reevaluated for practical use with an eye to material properties and its applicability to piping-experienced embankments was examined. Piping possibility was also examined in the present design criteria and compared. In view of the results achieved, it reflects that both yield piping possibility. But it's still necessary to complement how to judge and verify piping resistance of given soils with gradation curves by the representative curve, quantitatively and that piping resistance should consider compaction effects as well.