• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.376-379
• /
• 2006

Reaction Wheel Assembly (RWA) is one of the major disturbance sources that have influence upon the Line of Sight (LOS) of payload. A micro-vibration induced by RWA is propagated through the satellite structure and decrease the LOS stability performance of payload. This effect shall be analyzed through the jitter analysis. If a requirement or specification of payload jitter level is found to be not satisfied according to the jitter analysis campaign, some modification or redesign should be done on the satellite structure or a couple of isolator should be attached on the RWA interface in order to reduce the transmitted vibration level of RWA. The purpose of ???RWA isolator test? is to roughly evaluate the performance of vibration suppression level with a passive RWA isolator made of rubber. For this test, actual RWA is used as a vibration source and a couple of cube-shaped rubber mount designed for satellite is used as a passive isolator. There may be several considerations in order to accommodate RWA isolator to spacecraft such as not only vibration reduction performance but also thermal conduction problem, mechanical size, RWA alignment problem, etc. But in this report the feasibility of RWA isolator is analyzed only in a vibration suppression point of view. As a result, high frequency vibration of RWA above 50Hz is perfectly attenuated with isolators, however, first harmonic components below 50Hz became larger due to the additional low frequency resonance modes of roll, pitch, yaw rigid body motion of RWA+bracket.

• 센서학회지
• /
• 제26권4호
• /
• pp.235-238
• /
• 2017

In this study, the design of a tri-axis micromachined gyroscope is proposed and the vibration characteristic of the structure is analyzed. Tri-axis vibratory gyroscopes that utilize Coriolis effect are the most commonly used micromachined inertial sensors because of their advantages, such as low cost, small packaging size, and low power consumption. The proposed design is a single structure with four proof masses, which are coupled to their adjacent ones. The coupling springs of the proof masses orthogonally transfer the driving vibrational motion. The resonant frequencies of the gyroscope are analyzed by finite element method (FEM) simulation. The suspension beam spring design of proof masses limits the resonance frequencies of four modes, viz., drive mode, pitch, roll and yaw sensing mode in the range of 110 Hz near 21 kHz, 21173 Hz, 21239 Hz, 21244 Hz, and 21280 Hz, respectively. The unwanted modes are separated from the drive and sense modes by more than 700 Hz. Thereafter the drive and the sense mode vibrations are calculated and simulated to confirm the driving feasibility and estimate the sensitivity of the gyroscope. The cross-axis sensitivities caused by driving motion are 1.5 deg/s for both x- and y-axis, and 0.2 deg/s for z-axis.

• 대한조선학회논문집
• /
• 제53권3호
• /
• pp.217-227
• /
• 2016

Recent accidents of crude oil tankers have resulted in sinking, grounding of vessels and significant levels of marine pollution. Therefore, International Maritime Organization (IMO) has been strengthening the regulations of ship maneuvering performance in MSC 137. The evaluation of maneuvering performance can be made at the early design stage; it can be investigated numerically or experimentally. The main objective of this paper was to investigate the maneuvering performance of a VLCC due to the increase of rudder force at an early design stage for low speed in shallow water conditions. It was simulated in various operating condition such as deep sea, shallow water, design speed and low speed by using the numerical maneuvering simulation model, developed using MMG maneuvering motion equation and KVLCC 2 (SIMMAN 2008 workshop). The effect of increasing the rudder force can be evaluated by using numerical simulation of turning test and ZIG-ZAG test. The research showed that, increasing the rudder force of a VLCC was more effective on improving the turning ability than improving the course changing ability especially. The improvement of turning ability by the rudder force increasing is most effective when the ship is sailing in shallow water at low forward speed.

• 한국항해학회지
• /
• 제10권2호
• /
• pp.97-114
• /
• 1986

Ship's maneuverability is very important factor in safe ship handling and economical ship operation. Steering characteristics are consisted of course stability and maneuverability. Today in many advanced ship-building countries, they study ship's course stability, using model ship tests, such as straight line tests, rotating arm tests and Planar Motion Mechanism (PMM) etc., in tow in tanks. It is the purpose of this paper to provide ship's handlers with better understanding of steering characteristics and to help them in safe controlling and manevering . In this paper, the author simulated response of various vessels, running straight course with constant speed, and they are disturbed by small external disturbance of one degree yaw angle with no angular velocity . The author used the hydrodynamic derivtives resulted at tests of Davidson's laboratory in Stevens Institute of Technology, New Jersey, U.S.A. Course stability was evaluated and analyzed in various respects, such as block coefficient, ratio of ship's length to beam, draft and rudder area ratio etc. The obtained results are as follows : (1) The ship's course stability is affected by magnitude of block coefficient greatly. In case that the block coefficient is more than 0.7, the deviation varies at nearly same rate but the requistite time to reach the steady course is different. (2) The ship's course stability is affected by magnitude of L/B. When the dimensionless time reaches about 3, the deviation and requisite time to reach the steady course are influenced nearly same. After the dimensionless time is about 3, they change on invariable ratio. (3) The effect to course stability by L/T and RA' can be neglected. (4) The reason why thy VLCC and container feeder vessel are unstable on their course is that their block coefficient is generally more than 0.8 and the ratio of ship's length to beam is about 6.0.

• 한국항해항만학회지
• /
• 제42권2호
• /
• pp.127-136
• /
• 2018

The motion response of floating structures is of significant concern in marine engineering. Floating structures can be disturbed by waves, winds, and currents that create undesirable motions of the vessel, therefore causing challenges to its operation. For a floating structure, mooring lines are provided in order to maintain its position; these should also produce a restoring force when the vessel is displaced. Therefore, it is important to investigate the tension of mooring lines and the motion responses of a twin barge when moored to guarantee the safety of the barge during its operation. It is essential to precisely identify the characteristics of the motion responses of a moored barge under different loading conditions. In this study, the motion responses of a moored twin barge were measured in regular waves of seven different wave directions. The experiment was performed with regular waves with different wavelengths and wave directions in order to estimate the twin-barge motions and the tension of the mooring line. In addition, the motion components of roll, pitch, and heave are completely free. In contrast, the surge, sway, and yaw components are fixed. In the succeeding step, a time-domain analysis is carried out in order to obtain the responses of the structure when moored. As a result, the Response Amplitude Operator (RAO) motion value was estimated for different wave directions. The results of the experiment show that the motion components of the twin barge have a significant effect on the tension of the mooring lines.

• 품질경영학회지
• /
• 제49권3호
• /
• pp.245-254
• /
• 2021

Purpose: In order to accurately reach an underwater projectile to a target point, reliable INS and accurate arrangement of INS between master and slave INS is paramount. Unlike terrestrial and aerial environments, underwater projectile will operates in a restricted environment where location information cannot be received or sent through satellites. In this report, we review the factors affecting the transfer alignment of master and slave INS, as well as how to improve the positional error between INS through improved transfer alignment algorithms. Methods: In this work, we propose an improvement algorithm and verify it through simulation and driving test. The simulation confirmed the difference in the transfer alignment azimuth by fitting the MINS and SINS indoors, displacement in posture, and the process of transfer alignment between MINS and SINS through a driving test to confirm algorithm can improve the arrangement. Results: According to this study, reason for the error in the transfer alignment between MINS/SINS is the factors of the system where movements such as roll, pitch, yaw are not inter locked in real time due to the delay in transmit/receive system. And confirm that the improved algorithm has a desirable effect on accuracy. Conclusion: Through this work, it is possible to identify ways to improve the accuracy of underwater projectiles to reach their target points under various underwater environments and launch condition.

• 한국군사과학기술학회지
• /
• 제24권4호
• /
• pp.435-448
• /
• 2021

This study describes the depth and straight motion control performance depending on control surface combinations of a supercavitating underwater vehicle. When an underwater vehicle experiences supercavitation, friction resistance can be minimized, thus achieving the effect of super-high-speed driving. Six degrees of freedom modeling of the underwater vehicle are performed and the guidance and control loops are designed with not only a cavitator and an elevator, but also a rudder and a differential elevator to improve the stability of the roll and yaw axis. The control performance based on the combination of control surfaces is analyzed by the root-mean-square error for keeping depth and straight motion.

• 한국항해항만학회지
• /
• 제46권2호
• /
• pp.73-81
• /
• 2022

Currently, shipping by sea is becoming common because of the low price and the safety of goods. The ship is designed as a larger vessel to meet the need of this development. In the design stage, the investigation of hydrodynamic forces acting on the ship hull is very important in predicting the ship's maneuverability. Given that the ship docks at various ports for loading or discharging goods, the ship usually operates in various loading conditions, depending on the site condition and other various factors. Hence, it is necessary to investigate the effect of the loading condition on the hydrodynamic forces acting on the ship, to most accurately determine the maneuverability of the ship. In this study, an experiment of Korea Autonomous Surface Ship (KASS) was conducted at the towing tank of Changwon National University to measure the hydrodynamic forces acting on the KASS. The loading condition considered in this experiment is determined based on the draft, which was decreased by 5% for each loading condition. The smallest draft is 85% of the design draft. The static test as Oblique Towing Test (OTT), Circular Motion Test (CMT), Circular Motion Test with Drift (CMTD) is performed in the various loading conditions. First, the hydrodynamic forces in the Oblique Towing test (OTT) are compared with the result of other institutes. Second, the hydrodynamic forces in various drift angle, yaw rate and loading conditions are measured. Finally, the influence of the loading conditions on the hydrodynamic coefficient is discussed.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제16권9호
• /
• pp.3068-3086
• /
• 2022

Digital Forensics is gaining popularity in adjudication of criminal cases as use of electronic gadgets in committing crime has risen. Traditional approach to collecting digital evidence falls short when the disk is encrypted. Encryption keys are often stored in RAM when computer is running. An approach to acquire forensic data from RAM when the computer is shut down is proposed. The approach requires that the investigator immediately cools the RAM and transplant it into a host computer provisioned with a tool developed based on cold boot concept to acquire the RAM image. Observation of data obtained from the acquired image compared to the data loaded into memory shows the RAM chips exhibit some level of remanence which allows their content to persist after shutdown which is contrary to accepted knowledge that RAM loses its content immediately there is power cut. Results from experimental setups conducted with three different RAM chips labeled System A, B and C showed at a reduced temperature of -25C, the content suffered decay of 2.125% in 240 seconds, 0.975% in 120 seconds and 1.225% in 300 seconds respectively. Whereas at operating temperature of 25℃, there was decay of 82.33% in 60 seconds, 80.31% in 60 seconds and 95.27% in 120 seconds respectively. The content of RAM suffered significant decay within two minutes without power supply at operating temperature while at a reduced temperature less than 5% decay was observed. The findings show data can be recovered for forensic evidence even if the culprit shuts down the computer.

• 한국항해항만학회지
• /
• 제35권3호
• /
• pp.197-204
• /
• 2011

회류수조에서의 대각도 정적(static) 모형실험을 통해 Manta형 무인잠수체에 작용하는 동유체력을 측정하였으며, 동유체력에 미치는 Reynolds수의 영향을 고찰하였다. 이를 위해 동유체력을 cross-flow drag과 양력(lift force)으로 성분 분석을 하였으며, 양력 성분에는 Reynolds수의 영향을 무시하고, cross-flow drag 성분에만 Reynolds수의 영향을 고려하였다. 그 후 이들 두 성분을 다시 합성함으로써 실물 무인잠수정에 작용하는 동유체력의 추정 기법을 제시하였다.