• Journal of Radiation Protection and Research
• /
• v.20 no.1
• /
• pp.45-52
• /
• 1995

This study is to compare A point doses in human pelvic phantom by film dosimetry, computer planning and manual calculation by using of along-away table. We developed tissue equivalent human pelvic phantom composed of four pieces of cylindrical acryl tubes with water, to simulate intracavitary radiation (ICR) in patients with cervix cancer. When the phantom assembled from 4 pieces, it has a small space for inserting Fletcher-Suit-Delclos applicator like a human vagina. Fletcher-Suit-Delclos applicator inserted into the space was packed tightly with furacin gauzes, and three $^{137}Cs$ sources with radioactivity of $15.7mg\;Ra-eq$ were inserted into the tandem. For the film dosimetry, two pieces of X-OMAT V film (Kodak Co.) of which planes include point A, were arranged orthogonally in the slits between phantoms. A point dose and iso-dose curves were measured by means of optical densitometer. A point doses by film dosimetry, RTP system and manual calculation by using of along-away table were compared, and iso-dose curves by film dosimetry and computer planning were also compared. The dose of A point was 51.2cGy/hr by film dosimetry, 46.7cGy/hr by RTP system and 47.9 cGy/hr by along-away table. A point dose by computer planning was similar to the dose by calculation using of along-away table with acceptable accuracy $({\pm}3%)$, however, the dose by film dosimetry was different from two others with about 10% error. Since most clinical beams contains a scatter component of low energy photons, the correlation between optical density and dose becomes tenuous. In addition, film suffers from several potential errors such as changes in processing conditions, interfilm emulsion differences, and artifacts caused by air pockets adjacent to the film. For these reasons, absolute dosimetry with film is impractical, however, it is very useful for checking qualitative patterns of a radiation distribution. In future, solid state dosimeter such as TLD must be used for the dosimetry of ionizing radiation. When considerable care is used, precision of approximately 3% may be obtained using TLD.

• The Korean Journal of Pain
• /
• v.1 no.2
• /
• pp.214-222
• /
• 1988

With the arm in hyperabduction, we have carried out 525 procedures of supraclavicular brachial plexus block from Aug. 1976 to June 1980, whereas block with the arm in adduction has been customarily performed by other authors. The anesthetic procedure is as follows: 1) The patient lies in the dorsal recumbent position without a pillow under his head or shoulder. His arm is hyperabducted more than a 90 degree angle from his side, and his head is turned to the side opposite from that to be blocked. 2) An "X" is marked at a point 1 cm above the mid clavicle, immediately lateral to the edge of the anterior scalene muscle, and on the palpable portion of the subclavian artery. The area is aseptically prepared and draped. 3) A 22 gauge 3.5cm needle attached to a syringe filled with 2% lidocaine (7~8mg/kg of body weight) and epineprine(1 : 200,000) is inserted caudally toward the second portion of the artery where it crosses the first rib and parallel with the lateral border of the muscle until a paresthesia is obtained. 4) Paresthesia is usually elicited while inserting the needle tip about 1~2 em in depth. If so, the local anesthetic solution is injected after careful aspiration. 5) If no paresthesia is elicited, the needle is withdrawn and redirected in an attempt to elicit paresthesia. 6) If, after several attempts, no paresthesia is obtained, the local anesthetic solution is injected into the perivascular sheath after confirming that the artery is not punctured. 7) Immediately after starting surgery, Valium is injected for sedation by the intravenous route in almost all cases. The age distribution of the cases was from 11 to 80 years. Sex distribution was 476 males and 49 females (Table 1). Operative procedures consisted of 103 open reductions, 114 skin grafts combined with spinal anesthesia in 14, 87 debridements, 75 repairs, i.e. tendon (41), nerve(32), and artery (2), 58 corrections of abnormalities, 27 amputations above the elbow (5), below the elbow (3) and fingers (17), 20 primary closures, 18 incisions and curettages, 2 replantations of cut fingers. respectively (Table 2). Paresthesia was obtained in all cases. Onset of analgesia occured within 5 minutes, starting in the deltoid region in almost all cases. Complete anesthesia of the entire arm appeared within 10 minutes but was delayed 15 to 20 minutes in 5 cases and failed in one case. Thus, our success rate was nearly 100%. The duration of anesthesia after a single injection ranged from $3\frac{1}{2}$ to $4\frac{1}{2}$, hours in 94% of the cases. The operative time ranged from 0.5 to 4 hours in 92.4% of the cases(Table 3). Repeat blocks were carried out in 33 cases when operative times which were more than 4 hours in 22 cases and the others were completed within 4 hours (Table 4). Two patients of the 33 cases, who received microvasular surgery were injected twice with 2% lidocaine 20 ml for a total of $13\frac{1}{2}$ hours. The 157 patients who received surgery on the forearms or hands had pneumatic tourniquets (250 torrs) applied without tourniquet pain. There was no pneumothorax, hematoma or phrenic nerve paralysis in any of the unilateral and 27 bilateral blocks, but there was hoarseness in two, Horner's syndrome in 11 and shivering in 7 cases. No general seizures or other side effects were observed. By 20ml of 60% urcgratin study, we confirm ed the position of the needle tip to be in a safer position when the arm is in hyperabduction than when it is in adduction. And also that the humoral head caused some obstraction of the distal flow of the dye, indicating that less local anesthetic solution would be needed for satisfactory anesthesia. (Fig. 3,4).

• The Journal of Korean Academy of Prosthodontics
• /
• v.43 no.2
• /
• pp.232-247
• /
• 2005

Purpose. The purposes of this investigation were to discover the possibility of clinical application in the areas of dental implants and bone grafts by investigating the bone formation histologically around specimen which was depending on the intensity of magnetic field of neodymium magnet inside of the specimens. Material and method. 1. Measurement of magnetic intensity - placed the magnet inside of the specimen, and measured the intensity of magnetic field around the 1st thread and 3rd thread of specimen 20 times by using a Gaussmeter(Kanetec Co., Japan). 2. Surgical Procedure - Male rabbit was anesthetised by constant amount of Ketamine (0.25ml/kg) and Rompun (0.25ml/kg). After incising the flat part of tibia, and planted the specimens of titanium implant, control group was stitched without magnet, while experimental groups were placed a magnedisc 500(Aichi Steel Co., Japan) or magnedisc 800(Aichi Steel Co., Japan) into it, fixed by pattern resin and stitched. 3. Management after the surgery - In order to prevent it from the infection of bacteria and for antiinflammation, Gentamycin and Ketopro were injected during 1 week from operation day, and dressed with potadine. 4. Preparation of histomorphometric analysis - At 2, 4 and 8 weeks after the surgery, the animals were sacrificed by excessed Ketamine, and then, specimens were obtained including the operated part and some parts of tibia, and fixed it to 10% of PBS buffer solution. After embedding specimens in Technovit 1200 and B.P solution, made a H-E stain. Samples width was 75$\mu$m . In histological findings through the optical microscope and using Kappa image base program(Olympus Co. Japan), the bone contact ratio and bone area ratio of each parts of specimens were measured and analyzed. 5. Statistical analysis - Statistical analysis was accomplished with Mann Whitney U-test. Results and conclusion. 1. In histomorphometric findings, increased new bone formation was shown in both control & experimental groups through the experiment performed for 2, 4 & 8 weeks. After 4 weeks, more osteoblasts and osteoclasts with significant bone remodeling were shown in experimental groups. 2. In histomorphometric analysis, the bone contact ratios were 38.5% for experimental group 1, 29.5% for experimental group 2 and 11.9% for control group. Experimental groups were higher than control group(p<0.05) (Fig. 6, Table IV). The bone area ratios were 60.9% for experimental group 2, 46.4% for experimental group 1 and 36.0% for control group. There was no significantly statistical difference between experimental groups and control group(p<0.05) (Fig. 8, Table VII) 3. In comparision of the bone contact ratios at each measurement sites according to magnetic intensity, experimental group 2(5.6mT) was higher than control group at the 1st thread (p<0.05) and experimental group 1 (1.8mT) was higher than control group at the 3rd thread(p<0.05) (Fig. 7, Table V, VI). 4. In comparision of the bone area ratios at each measurement sites according to magnetic intensity, experimental group 2(5.6mT) was higher than control group and experimental group 1 (4.0mT) at the 1st thread(p<0.1) and experimental group 2(4.4mT) was higher than experimental group 1 (1.8mT) at the 3rd thread(p<0.1) (Fig. 9, Table IX, X). Experiment group 2 was largest, followed by experiment group l and control group at the 3rd thread of implant. There was a significant difference at the 1st thread of control group & experiment group 2, and at 1st thread & 3rd thread of experiment group 1 & 2, and not at control group experiment group 1.(p<0.1)

• Radiation Oncology Journal
• /
• v.1 no.1
• /
• pp.21-24
• /
• 1983

The thickness of the part being irradiated is finite. Percent depth dose tables being used routinely are generally obtained from dosimetry in a phantom much thickner than usual patient. At or close to exit surface, the dose should be less than that obtained from the percent depth dose tables, because of insufficient volume for backscattering. To know the difference between the true absorbed dose and the dose obtained from percent depth dose table, the doses at or close to the exit surface were measured with plate type ionization chamber with volume of 0.5ml. The results are as follows; 1. In the case of $^{60}Co$, percent depth dose at a given depth increases with underlying phantom thickness up to the 5cm. 2. In the case of $^{60}Co$, the dose correction factor at exit surface which is less than 1, increases with part thickness and decreases with field size. 3. Exposure time may not be corrected when the part above 10cm in thickness is treated by $^{60}Co$. 4. In the case of 10MV x-ray, the dose correction factor is nearly 1 and constant for the underlying phantom thickness and field size, so the correction of monitor unit is not necessary for part thickness.

• Journal of Sericultural and Entomological Science
• /
• v.8
• /
• pp.11-25
• /
• 1968

Various formulae for estimation of leaf production in mulberry trees were investigated and obtained. Four varieties of mulberry trees were used as the materials, and seven characters namely branch length. branch diameter, node number per branch, total branch weight, branch weight except leaves, leaf weight and leaf area, were studied. The formulae to estimate the leaf yield of mulberry trees are as follows: 1. Varietal differences were appeared in means, variances, standard devitations and standard errors of seven characters studied as shown in table 1. 2. Y$_1$=a$_1$X$_1$${\times}$P$_1$......(l) where Y$_1$ means yield per l0a by branch number and leaf weight determination. a$_1$.........leaf weight per branch. X$_1$.......branch number per plant. P$_1$........plant number per l0a. 3. Y$_2$=(a$_2$${\pm}$S. E.${\times}$X$_2$)+P$_1$.......(2) where Y$_2$ means leaf yield per l0a by branch length and leaf weight determination. a$_2$......leaf weight per meter of branch length. S. E. ......standard error. X$_2$....total branch length per plant. P$_1$........plant number per l0a as written above. 4. Y$_3$=(a$_3$${\pm}$S. E${\times}$X$_3$)${\times}$P$_1$.....(3) where Y$_3$ means of yield per l0a by branch diameter measurement. a$_3$.......leaf weight per 1cm of branch diameter. X$_3$......total branch diameter per plant. 5. Y$_4$=(a$_4$${\pm}$S. E.${\times}$X$_4$)P$_1$......(4) where Y$_4$ means leaf yield per 10a by node number determination. a$_4$.......leaf weight per node X$_4$.....total node number per plant. 6. Y$\sub$5/= {(a$\sub$5/${\pm}$S. E.${\times}$X$_2$)Kv}${\times}$P$_1$.......(5) where Y$\sub$5/ means leaf yield per l0a by branch length and leaf area measurement. a$\sub$5/......leaf area per 1 meter of branch length. K$\sub$v/......leaf weight per 100$\textrm{cm}^2$ of leaf area. 7. Y$\sub$6/={(X$_2$$\div$a$\sub$6/${\pm}$S. E.)}${\times}$K$\sub$v/${\times}$P$_1$......(6) where Y$\sub$6/ means leaf yield estimated by leaf area and branch length measurement. a$\sub$6/......branch length per l00$\textrm{cm}^2$ of leaf area. X$_2$, K$\sub$v/ and P$_1$ are written above. 8. Y$\sub$7/= {(a$\sub$7/${\pm}$S. E. ${\times}$X$_3$)}${\times}$K$\sub$v/${\times}$P$_1$.......(7) where Y$\sub$7/ means leaf yield estimates by branch diameter and leaf area measurement. a$\sub$7/......leaf area per lcm of branch diameter. X$_3$, K$\sub$v/ and P$_1$ are written above. 9. Y$\sub$8/= {(X$_3$$\div$a$\sub$8/${\pm}$S. E.)}${\times}$K$\sub$v/${\times}$P$_1$.......(8) where Y$\sub$8/ means leaf yield estimates by leaf area branch diameter. a$\sub$8/......branch diameter per l00$\textrm{cm}^2$ of leaf area. X$_3$, K$\sub$v/, P$_1$ are written above. 10. Y$\sub$9/= {(a$\sub$9/${\pm}$S. E.${\times}$X$_4$)${\times}$K$\sub$v/}${\times}$P$_1$......(9) where Y$\sub$7/ means leaf yield estimates by node number and leaf measurement. a$\sub$9/......leaf area per node of branch. X$_4$, K$\sub$v/, P$_1$ are written above. 11. Y$\sub$10/= {(X$_4$$\div$a$\sub$10/$\div$S. E.)${\times}$K$\sub$v/}${\times}$P$_1$.......(10) where Y$\sub$10/ means leaf yield estimates by leaf area and node number determination. a$\sub$10/.....node number per l00$\textrm{cm}^2$ of leaf area. X$_4$, K$\sub$v/, P$_1$ are written above. Among many estimation methods. estimation method by the branch is the better than the methods by the measurement of node number and branch diameter. Estimation method, by branch length and leaf area determination, by formulae (6), could be the best method to determine the leaf yield of mulberry trees without destroying the leaves and without weighting the leaves of mulberry trees.

• Journal of the Korean Society of Radiology
• /
• v.6 no.6
• /
• pp.455-464
• /
• 2012

This study suggested evaluation of approximately exposure to low-dose ionization radiation from medical images using a computed radiography (CR) system in standard X-ray examination and experimental model can compare diagnostic reference level (DRL) will suggest on optimization condition of guard about medical radiation of low dose space. Entrance surface dose (ESD) cross-measuring by standard dosimeter and optically stimulated luminescence dosimeters (OSLDs) in experiment condition about tube voltage and current of X-ray generator. Also, Hounsfield unit (HU) scale measured about each experiment condition in CR system and after character relationship table and graph tabulate about ESD and HU scale, approximately radiation dose about head, neck, thoracic, abdomen, and pelvis draw a measurement. In result measuring head, neck, thoracic, abdomen, and pelvis, average of ESD is 2.10, 2.01, 1.13, 2.97, and 1.95 mGy, respectively. HU scale is $3,276{\pm}3.72$, $3,217{\pm}2.93$, $2,768{\pm}3.13$, $3,782{\pm}5.19$, and $2,318{\pm}4.64$, respectively, in CR image. At this moment, using characteristic relationship table and graph, ESD measured approximately 2.16, 2.06, 1.19, 3.05, and 2.07 mGy, respectively. Average error of measuring value and ESD measured approximately smaller than 3%, this have credibility cover all the bases radiology area of measurement 5%. In its final analysis, this study suggest new experimental model approximately can assess radiation dose of patient in standard X-ray examination and can apply to CR examination, digital radiography and even film-cassette system.

• Korean Journal of Food Science and Technology
• /
• v.50 no.3
• /
• pp.331-338
• /
• 2018

The purpose of this study was to determine the optimum sterilization conditions for the production of retorted steamed egg using response surface methodology. Sterilization processes for eighteen conditions using varying sterilization temperature ($X_1$), time ($X_2$), and method ($X_3$) as the independent variables were carried out through a $3^2{\times}2$ experimental factorial design. Quality evaluations after sterilization included measurements of $F_0$ value ($Y_1$), peak stress ($Y_2$), pH ($Y_3$), color value ($Y_{4-6}$), and organoleptic test [preference for appearance ($Y_7$), overall acceptability ($Y_8$), and preference for texture ($Y_9$) and egg taste ($Y_{10}$)]. Dependent variables ($Y_{1-10}$) of eighteen conditions were more affected by temperature and time than by the sterilization method. Eight factors were selected among the dependent variables as significant factors related to the quality of the steamed egg. Finally, by establishing an optimum range of each dependent variable and contour analysis, the optimum sterilization conditions for the production of steamed egg were determined to be $120^{\circ}C$ for 25 min using a 2-step sterilization process.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.6
• /
• pp.187-193
• /
• 2015

The ICT healing platform sets a couple of goals including preventing chronic diseases and sending out early disease warnings based on personal information such as bio-signals and life habits. The 2-step open system(TOS) had a relay designed between the healing platform and the storage of personal health data. It also took into account a publish/subscribe(pub/sub) service based on large-scale connections to transmit(monitor) the data processing process in real time. In the early design of TOS pub/sub, however, the same buffers were allocated regardless of connection idling and type of message in order to encode connection messages into a deflate algorithm. Proposed in this study, the dynamic buffer allocation was performed as follows: the message transmission type of each connection was first put to queuing; each queue was extracted for its feature, computed, and converted into vector through tf-idf, then being entered into a k-means cluster and forming a cluster; connections categorized under a certain cluster would re-allocate the resources according to the resource table of the cluster; the centroid of each cluster would select a queuing pattern to represent the cluster in advance and present it as a resource reference table(encoding efficiency by the buffer sizes); and the proposed design would perform trade-off between the calculation resources and the network bandwidth for cluster and feature calculations to efficiently allocate the encoding buffer resources of TOS to the network connections, thus contributing to the increased tps(number of real-time data processing and monitoring connections per unit hour) of TOS.

• Journal of the Korean Society of Radiology
• /
• v.9 no.7
• /
• pp.467-471
• /
• 2015

This study's purpose is improve image quality to keep accurate tube angle in order to recognize distortion degree conditions by patient's position or tube angle and to provide exact clinical informations when taking chest AP projection for patient which have L-tube in stomach. The experimental equipment was ELMO-T6S by SHIMADZU corporation, then we put L-tube which attached 1 mm gap scales ruler on chest phantom surface. The experiment set by 90 kVp, 4 mAs, 120 cm distance. Each phantom position which changed supine, 30degree, 45degree, 60degree on the table exposured direct, ${\pm}5degree$, ${\pm}10degree$, ${\pm}15degree$ to head and feet directions. As a result, L-tube tip's position was changed by patient's position and tube angle. When patient's position is supine, tip's position change was lower than 30degree, 45degree, 60degree. We have to adjust patient's position or tube angle in order to occur image distortion by fault tube angle when confirming correct position L-tube tip through chest x-ray. Also, Radiological technologist try to make accurate evaluation index for satisfied L-tube insertion.

• Proceedings of the Korean Society for Bio-Environment Control Conference
• /
• 2001.04b
• /
• pp.71-72
• /
• 2001

최근 수출오이의 재배 면적이 계속증가 추세에 있어 '99년 현재 143ha에 달하고 있다. 그러나 수출오이는 국내 오이와 재배방법이 상당히 달라 국내 오이는 주지착과형이지만 수출오이는 측지착과형으로 측지의 발생여부에 따라 수확량의 차이가 심하다. 따라서 수출오이의 성공여부는 측지발생을 어느정도 시키느냐에 달려 있다고 해도 과언이 아니다. 그런데 수출오이의 재배시기는 우리나라에서 재배환경이 가장 불량한 겨울철(10-2월)로, 저온 및 투광량 부족 등으로 인하여 측지발생율이 매우 저조하다. 따라서 본 시험은 수출오이의 측지 발생율을 높이고자 지중가온기 설치 여부에 따른 효과를 구명하고자 실시하였다. 그 결과, 생육(Table 1)은 접수의 줄기 직경이 지중가온 처리시 10.22mm로, 무가온의 8.64mm보다 굵었고, 엽장과 엽폭에 있어서도 지중가온 처리가 무가온 처리보다 좋았다. 곡과 발생수에 있어서도 지중가온 처리는 주당 0.73개가 발생하였으나, 무가온은 1.26개가 발생되어 지중가온 처리시 무가온에 비해서 생육이 좋아지고, 곡과 발생이 적었다. 주당 측지발생수(Table 2)는 지중가온구가 13.7개였고, 무가온구는 11.7개로 지중가온을 하면 측지발생수가 증가함을 알수 있었다. 또한 상품수확과수에 있어서도 지중가온구는 주당 45개인데 반해 지중무가온구는 38개였으며 따라서 전체적인 수량이 10a당 8,100kg으로, 무가온구의 6,840kg보다 18%의 증수효과가 있었다. 따라서 수출오이재배시 지중가온을 하면, 측지발생수가 증가하고 특히 장측지(Fig. 1)가 다수 발생하여 측지 수확과수가 증가하며, 곡과 등 기형과 발생이 감소하여 상품수량이 증가되므로써 기존 지중 무가온 재배에 비해 14% 소득향상 효과를 기대할 수 있다.시 생장이 둔화되었다. 밀폐시킨 삼각플라스크에서 자라는 Cell은 상태도 좋지 않고 전반적인 증식량도 적었다. Cell은 환기정도에 민감한 것으로 판단되며 삼각플라스크에서 약 35일 정도의 생장 주기를 가지는 것으로 사료된다. 배양 3주까지는 플라스틱 뚜껑으로 밀폐시킨 bottle에서 가장 많은 체세포배를 얻었다. Air filter를 달아 2일 마다 신선한 공기를 넣어 주었을 때는 배의 발달이 많이 늦어져 배양 3주째에 다른 처리보다 배의 수가 훨씬 적었다. 체세포배가 발달하는 동안에는 산소를 많이 요구하지 않으나 성숙하는 동안에는 산소를 많이 요구하는 것으로 생각된다.적인 것으로 나타났다. 다만, 곡선형은 물론 직선형에서도 열교환 튜브의 배치밀도, 튜브 길이 및 두께 등의 변화에 따른 최적화 연구가 수반되어야 할 것으로 판단된다.에서 제공된 API는 객체기반 제작/편집 도구에 응용되어 다양한 멀티미디어 컨텐츠 제작에 사용되었다.x factorization (NMF), generative topographic mapping (GTM)의 구조와 학습 및 추론알고리즘을소개하고 이를 DNA칩 데이터 분석 평가 대회인 CAMDA-2000과 CAMDA-2001에서 사용된cancer diagnosis 문제와 gene-drug dependency analysis 문제에 적용한 결과를 살펴본다.0$\mu$M이 적당하며, 초기배발달을 유기할 때의 효과적인 cysteamine의 농도는 25~50$\mu$M인 것으로 판단된다.N)A(N)/N을 제시하였다(A(N)=N에 대한 A값). 위의 실험식을 사용하여 헝가리산 Zempleni 시료(15%$S_{XRD}$)의 기본입자분포로부터 %$S_{XRD}