• Journal of Powder Materials
• /
• v.10 no.5
• /
• pp.305-309
• /
• 2003

We report on the formation and chemical leaching of non-equilibrium $Al_{0.6}(Fe_{75}Co_{25})$ alloy produced by rod milling. X-ray diffractometry, transmission electron microscopy, differential scanning calorimetry, scanning electron microscopy, and vibrating sample magnetometry were used to characterize the as-milled and leached specimens. After 400 h, only the $Al_{0.4}Fe_{0.6}$ peak of the body-centered cubic type was present in the XRD pattern. The entire rod milling process could be divided into three different stages of milling: agglomeration, disintegration, and homogenization. The saturation magnetization, $M_s$ decreased with increased milling time, the $M_s$ of the powders before milling was about 113.8 emu/g, the $M_s$ after milling for 400 h was about 11.55 emu/g. Leaching of the Al in KOH of the Al at room temperature from the as-milled powders did not induce any significant change in the diffraction pattern. After the leached specimen had been annealed at $600^{\circ}C$ for 1 hour, the nanoscale crystalline phases were transformed into the bcc Fe, cubic Co, and $CoFe_2O_4$ phases. On cooling the specimen from 85$0^{\circ}C$, the degree of magnetization increased slightly, then increased sharply at approximately 364.8$^{\circ}C$, indicating that the bcc $Al_{0.4}Fe_{0.6}$ phase had been transformed to the Fe and Co phases.

• Journal of Pharmaceutical Investigation
• /
• v.41 no.6
• /
• pp.371-376
• /
• 2011

The objective of this work was to investigate the existence of new crystal forms of tulobuterol which is used to prevent morning asthma attacks by ${\beta}_2$ agonist and the transformation of crystal forms. Three crystal forms of tulobuterol have been isolated by recrystallization and Form 2 was transformed to Form 4 at 52% RH and 95% RH and these four crystal forms are characterized by differential scanning calorimetry (DSC), powder X-ray diffractometry (PXRD) and thermogravimetric analysis (TG). The DSC and PXRD patterns of four crystal forms of tulobuterol were different respectively. The dissolution patterns of these three crystal forms of tulobuterol were studied and they showed significant differences in the dissolution rate. After storage of 2 months at 0% RH (silica gel, $20^{\circ}C$), 52% RH (saturated solution of $Na_2Cr_2O_7{\cdot}2H_2O/20^{\circ}C$) and 95% RH (saturated solution of $Na_2HPO_4/20^{\circ}C$), Form 1 and Form 3 were not transformed. But Form 2 was transformed to Form 4 at 52% RH and 95% RH.

• Applied Chemistry for Engineering
• /
• v.16 no.1
• /
• pp.150-152
• /
• 2005

$La_{0.2}Ca_{0.8}MnO_3$ colossal magnetoresistance (CMR) powders and pellets were synthesized by sol-gel process involving a stable metal chelate complex with acetylacetone. The structural changes of reaction mixture were monitored by FT-IR spectroscopy and X-ray diffractometry. The microstructure of sintered samples and the cation composition of gel powder were studied by FE-SEM/EDS and ICP-AES. The magnetic property was investigated as a function of temperature.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.1
• /
• pp.50-55
• /
• 1999

To develop a new form of controlled release dosage for administering for indomethacin (IND), two formulations of IND-loaded nanoparticles were designed based on polysaccharide (guar) derivatives. Nanoparticles prepared by the dialysis method were characterized with respect to morphology, size distribution, drug content, and in vitro drug release. Morphological studies by scanning electron microscopy (SEM) indicated that guar acetate (GA) nanoparticles were spherical in shape and had a smooth surface. The particle size distributions of formulation I (40mg of GA) and formulation II (80mg of GA) were shown to be $250.78\pm185.13nm$ and $718\pm145.90nm$ in distilled water ($20$^{\circ}C$), respectively. The drug loading efficiencies of nanoparticles were approximately 26% and 31% for formulations I and II, respectively. The differential scanning calorimetry (DSC) results indicated that the IND was perfectly distributed within GA nanoparticles. We also found, from the X-ray diffractometry analysis, that a decrease in the degree of crystallinity of the drug occurred in the nanoparticles. No changes between the original IND and the released IND from GA nanoparticles were detected by FT-IR. Using guar acetate, it is possible to design nanoparticles which allow the controlled release of IND over an extended period of time.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.2
• /
• pp.111-114
• /
• 2001

This paper presents the influence of the additive composition on flexural strength and hardness of SiC-TiC composites materials for spectacle lens cutting materials. The materials were hot-pressed at $1800^{\circ}C$ and subsequently annealed at $1910^{\circ}C$ for 3h. The heating rate was $15^{\circ}C/min$ and the cooling rate about $25^{\circ}C/min$ in from the sintering temperature to $1300^{\circ}C$. The growth of particles of spectacle lens cutting materials was analysed by SEM and crystalline phases were discussed by x-ray diffractometry. Typical fracture toughness and hardness of materials for spectacle lens cutting were $6.1MPa{\cdot}m^{1/2}$ and 14.9 GPa, respectively.

• Journal of the Korean Ceramic Society
• /
• v.55 no.2
• /
• pp.178-184
• /
• 2018

In the present study, $TiB_2-Co$ composite coatings were thermally sprayed onto the surface of a 304 stainless steel substrate using an atmospheric plasma spray (APS). The phase analysis of the powders and plasma-sprayed coatings was performed using X-ray diffractometry analysis. The microstructures of the coatings were studied by a scanning electron microscope (SEM). The average particle size and flowability of the feedstocks were also measured. Both $TiB_2-32Co$ and $TiB_2-45Co$ (wt.%) coatings possessed typical dense lamellar structures and high-quality adhesion to the substrate. The oxidation behaviors of the coatings were studied at $900^{\circ}C$ in an atmospheric environment. In addition, the cross-sectional images of the oxidized coatings were analyzed by SEM. A thin and well-adhered layer was formed on the surface of both $TiB_2-Co$ coatings, confirming satisfactory high-temperature oxidation resistance. The kinetic curves corresponding to the isothermal oxidation of the coatings illustrated a short transient stage from rapid to slow oxidation during the early portion of the oxidation experiment.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1279-1281
• /
• 1998

The Co-Cr thin films are one of the most suitable candidates for perpendicular magnetic recording media. The facing targets sputtering(FTS) method has a advantage of preparing films over a wide range of working gas pressure on plasma-free substrates. In this study, we investigated the possibility of employing FTS system for depositing Co-Cr films, Co-Cr thin films were deposited with continuously sputter gas pressure ($P_{Ar}$ = 0.1 mTorr) by FTS method at temperature of $40^{\circ}C$. We find that the change of thickness and deposition rate of sputtered Co-Cr thin films affect crystal orientation and magnetic properties. Crystallographic and magnetic properties were evaluated by x-ray diffractometry(XRD) and vibrating sample magnetometer(VSM) respectively. It has been confirmed that the FTS method is very useful for preparing Co-Cr thin film recording media.

• Journal of the Korean Applied Science and Technology
• /
• v.16 no.3
• /
• pp.255-262
• /
• 1999

The new copolymers which contain flexible spacers in main chain were prepared and their properties were studied. the copolymers were synthesized in the melt polymerization melted from diacetoxynaphthalene isomers, ${\alpha},{\omega}bis(4-carboxyphenoxy)$ alkanes and p-acetoxy benzoic acid in the molar ratio of 1:1:2 and characterized for the effects of structure of naphthalenediol isomer moieties and the spacers on thermal crystalline and liquid crystalline properties of the resulting polymers. Diacetoxy naphthalene isomers were used 1. 5-,1. 6-,2. 6-and 2. 7-disubstituted ones and the spacers was either tetramethylene or decamethylene. The polymer was characterized by elemental and spectropic analysis, differential scanning calorimetry (DSC) on a polaring microscope, wide-angle X-ray diffractometry and thermogravimetry (TGA). There glass transition temperatures (Tg) and melting temperature (Tm) on the structure of the naphthalenediol isomer moieties and the length of the spacers. The presence of spacers was found to the helpful in crystallization of 1. 6-naphthalenediol copolyesters. The presence of amide group in the backbone chain of polymer was found to increase transition temperature, crystallization, thermal stability of polymers but to decreas solubility.

• Journal of the Korean institute of surface engineering
• /
• v.29 no.6
• /
• pp.666-672
• /
• 1996

The optical property of CdTe thin film is important for applications such as the compound semiconductor type solar cells. CdTe films are prepared by RF sputtering at various substrate temperature between $25^{\circ}C$ and $300^{\circ}C$, then, annealed in argon gas environment at $400^{\circ}C$. The annealing process of the thin film caused variation in the film structure and the composition of films. The deformation of CdTe thin film was observed by X-ray diffractometry. After annealing, the grain size increased and the portion of the non-crystalline CdTe reduced. Futhermore, the structure of sputtered CdTe film grown at the substrate temperature more than $250^{\circ}C$ was enhanced in the (111) direction of zincblend structure. There was a discrepancy, in the spectroscopic ellipsometer spectrum, between the single crystal CdTe and the sputtered CdTe thin films, especially in the region over 3.2eV. An oxidation layer was found on the CdTe thin film by spectroscopic ellipsometry analysis.

• Journal of the Korean Society for Heat Treatment
• /
• v.17 no.5
• /
• pp.299-304
• /
• 2004

Influence of Ca addition on microstructure and room temperature mechanical properties has been studied for AZ31(Mg-3%Al-1%Zn-0.2%Mn)-(0~0.5)%Ca wrought alloys, based on experimental results from metallography, X-ray diffractometry and mechanical tests. Yield strength, ultimate tensile strength and hardness of the alloys increased remarkably with increasing Ca content, whereas elongation was deteriorated continuously. Microstructural examination revealed that Ca addition efficiently refined grains of ${\alpha}$(Mg) phase and that some of the Ca dissolved in ${\beta}(Mg_{17}Al_{12})$ precipitates. The former and the latter facts are thought to be responsible for improved strength and loss of ductility of the AZ31+Ca wrought alloys, respectively.