• Journal of Sensor Science and Technology
• /
• v.6 no.4
• /
• pp.328-336
• /
• 1997

The CdSe thin films were grown on the Si(100) wafers by a hot wall epitaxy method (HWE). The source and substrate temperature are $600^{\circ}C$ and $430^{\circ}C$ respectively. The crystalline structure of epilayers was investigated by double crystal X-ray diffraction(DCXD). Hall effect on the sample was measured by the van der Pauw method and studied on the carrier density and mobility dependence on temperature. From Hall data, the mobility was increased in the temperature range 30K to 150K by impurity scattering and decreased in the temperature range 150k to 293k by the lattice scattering. In order to explore the applicability as a photoconductive cell, we measured the sensitivity(${\gamma}$), the ratio of photocurrent to darkcurrent(pc/dc), maximum allowable power dissipation(MAPD), spectral response and response time. The results indicated that the photoconductive characteristic were the best for the samples annealed in Cu vapor compare with in Cd, Se, air and vacuum vapour. Then we obtained the sensitivity of 0.99, the value of pc/dc of $1.39{\times}10^{7}$, the MAPD of 335mW, and the rise and decay time of 10ms and 9.5ms, respectively.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.7
• /
• pp.473-482
• /
• 2009

In this study, iron and manganese coated sand (IMCS) was prepared by mixing Joomoonjin sand with solutions having different molar ratio of manganese ($Mn^{2+}$) and iron ($Fe^{3+}$). Mineral type of IMCS was analyzed by X-ray diffraction spectroscopy. Removal efficiency of arsenic through As(III) oxidation and As(V) adsorption by IMCS having different ratio of Mn/Fe was evaluated. The coated amount of total Mn and Fe on all IMCS samples was less than that on sand coated with iron-oxide alone (ICS) or manganese-oxide alone (MCS). The mineral type of the manganese oxide on MCS and iron oxides on ICS were identified as ${\gamma}-MnO_2$ and mixture of goethite and magnetite, respectively. The same mineral type was appeared on IMCS. Removed amount As(V) by IMCS was greatly affected by the content of Fe rather than by the content of Mn. Adsorption of As(V) by IMCS was little affected by the presence of monovalent and divalent electrolytes. However a greatly reduced As(V) adsorption as observed in the presence of trivalent electrolyte such as $PO_4\;^{3-}$. As(III) oxidation efficiency by MCS in the presence of NaCl or $NaNO_3$ was two times greater than that in the presence of $PO_4\;^{3-}$. Meanwhile a greater As(III) oxidation efficiency was observed by IMCS in the presence of $PO_4\;^{3-}$. This was explained by the competitive adsorption between phosphate and arsenate on the surface of IMCS.

• Economic and Environmental Geology
• /
• v.25 no.4
• /
• pp.397-416
• /
• 1992

In the present study, three clay deposits, named the Seongsan, Ogmaesan and Haenam deposits, were investigated. The altered zones are recognized in the hydrothermally altered rocks of the clay deposits from the center of the alteration to the margin: Kaolin, Kaolin-Quartz, Quartz, Sericite and Chlorite zones in the Seongsan deposits; Quartz zone, Alunite zone, Kaolin zone, Sericite zone and Chlorite zone in the Ogmaesan deposits; Quartz zone, Pyrophyllite zone, Sericite zone and Chlorite zone in the Haenam deposits. These zones can be grouped into two types of alteration: Acidic alteration such as Pyrophyllite zone, Alunite zone, Quartz zone, Kaolin zone, Kaolin-Quartz zone and a part of Sericite zone; Propylitic alteration such as Chlorite zone and a part of Sericite zone. All clay deposits belong to high-sulfidation (acid-sulfate) system. The rocks of the acidic alterations are composed of pyrophyllite, alunite, kaolin minerals, sericite, quartz and pyrite. On the basis of bulk chemical compositions, it was found that some components such as $SiO_2$, $TiO_2$, $Fe_2O_3$, FeO, MgO, CaO, $K_2O$ and $Na_2O$ were mobilized considerably from the original rocks. The mobility of these major elements is related to, and controls, mineral assemblages in each altered zone. Polytypes of sericite are determined as $2M_1$ and 1M by X-ray diffraction method. The amount of $2M_1$ is nearly equal to that of 1M in the Seongsan deposits whereas $2M_1$ is less and higher than that of 1M in the Ogmaesan and the Haenam deposits. These facts indicate that formation temperature of sericite is relatively high in the Haenam deposits, moderate in the Seongsan deposits, and low in the Ogmaesan deposits. The ratios of Na/(K+Na) for alunite in the Ogmaesan deposits determined by electron microprobe analyzer (EPMA) are higher than those in the Seongsan deposits. Thus, the alunite of the Ogmaesan deposits must have been formed from the solutions with relatively high aqueous Na/(K+Na) ratios and low pH at a high temperature rather than that of the Seongsan deposits. From all data, it is clarified that alunite is hypogene in origin, and has been formed by oxidation of hydrogen sulfide in the steam-heated environment, and that alunite has been produced by the spectacular solfataric alteration observed at the surface of some present-day hydrothermal systems.

• Journal of the Mineralogical Society of Korea
• /
• v.4 no.1
• /
• pp.22-31
• /
• 1991

Three crystal structures of dehydrated $Ag^+$-and $Ca^{2+}$- exchanged zeolite $A(Ag_4Ca_4-A,\;Ag_^Ca_3-A,\;and\;Ag_8Ca_2-A)$ treated at 250${\circ}C$ with 0.1 Torr of Rb vapor have been determined by single-crystal x-ray diffraction techniques in the cubic space group Pm3m at 21(1)${\circ}C$ (a=12,271(1)${\AA}$, 12.255(1)${\AA}$, and 12.339(1)${\AA}$, respectively). Their structures were refined to the final error indices. R(weighted) of 0.072 with 130 reflections, 0.050 with 110 reflections, and 0.083 with 86 reflections, respectively, for which $I>3{\rho}(I)$. In each structure, Rb species are found at three different crystallographic sites:3$Rb^+$+ions per unit cell are located at 8-ring centers, ca. 5.6 to 6.4 $Rb^+$ ions are found opposite 6-rings on threefold axes in the large cavity, and ca. 2.5 to 3.0 $Rb^+$ ions are found on threefold axes in the sodalite unit. Also, Ag species are found at two different crystallographic stites: ca. 0.7 to 2.1 $Ag^+$ lie opposite 4-rings and ca. 2.2 to 4.8 Ag atoms are located near the center of the large cavity. In these structures, the numbers of Ag atoms per unit cell are 2.2, 2.4, and 4.8, respectively, and these may form hexasilver clusters at the centers of the large cavities. The $Rb^+$ ions, by blocking 8-rings, may have prevented silver from migrating out of the structure. Each hexasilver cluster is stabilized by coordination to up to 13 $Rb^+$ions. An excess absorption of about 0.8 Rb atom per unit cell indicates that the presence of a triangular symmetric $(Rb_3)2^{+}$ cation in sodalite cavity. At least one large-cavity six-ring $Rb^+$ ion must necessarily approach this cluster and may be viewed as a member of it to give $(Rb)_4^{3+}$, $(Rb)_5^{4+}$ or $(Rb)_6^{5+}$.

• Korean Journal of Food Science and Technology
• /
• v.32 no.2
• /
• pp.252-257
• /
• 2000

The physicochemical and pasting properties of amaranth starches isolated from five cultivars, Andy, Suvarna, Nu World, K266-1, K432, grown in Korea, were investigated. The shapes of starch granules were all polygonal and size was in the range $1.14{\sim}1.48\;{\mu}m$ for all five cultivars. X-ray diffractograms were shown typical A type diffraction patterns for all amaranth starches. The protein and crude lipid contents of starches were $0.13{\sim}0.23%$ and $0.01{\sim}0.05%$, respectively. The apparent amylose contents ranged from $2.79{\sim}4.35%$ and the water binding capacities were $128.05{\sim}135.80%$. The transmittances of 0.1% amaranth starch suspensions except K266-1 increased rapidly above $65^{\circ}C$, thereafter increased slowely. The initial pasting and peak temperature ranges of five cultivars by RVA were $71.3{\sim}73.7^{\circ}C$ and $81.5{\sim}84.0^{\circ}C$, respectively. The peak and cooling viscosities followed the order : Nu World>Andy>Suvarna>K432>>K266-1. Nu World was shown the highest peak (166), final (103) and cooling viscosities (30 RVU). K266-I exhibited the lowest setback (-38) of all five cultivars. Gelatinization (To) and peak temperature (Tp) of amaranth starches in DSC thermograms were $65.7{\sim}68.0^{\circ}C$ and $70.6{\sim}75.8^{\circ}C$, respectively. Enthalpies followed the order: K266-1

• Korean Journal of Soil Science and Fertilizer
• /
• v.44 no.5
• /
• pp.916-921
• /
• 2011

This study was carry out on a Jang-Won series (fine loamy, mixed, mesic family of typic fragipan) that were established and classified as a fragipan soil in Korea. The morphological, physical, chemical and minerals characteristics of Jang-Won series were studied to determine the genesis of fragipan soils in natural environment. Each sample was analyzed for its physical, chemical and mineralogical characteristics. The particle size distribution of samples was measured using pipette method. Clay minerals were investigated on parallel-oriented specimens of the clay fraction ($<2{\mu}m$) from each horizon, separated by sieving and centrifugation, using X-ray diffraction (XRD) analysis. Micromorphological observations were made on thin sections prepared from soil blocks impregnated with Crystic Resin, cut and ground to less than $30{\mu}m$ in thickness, and finally polished with diamond paste. Most horizons have pH values in the range of fewer than 5.0 and have very low base-saturation values. Their textural classification ranges from silt loam to loam, the lower horizons being the finer. The clay fraction revealed the occurrence of illite, kaolinite, chlorite and vermiculite. The micro-morphological analysis carries out thin sections from each soil profile. The silt concentrations occur as extremely dense and homogenous bands or zones of silt-sized materials, brownish in colour in plane-polarized light and anisotropic in cross-polarized light, surrounding or adhering to skeleton grains. The genesis of fragipan in the Jangweon series assumed composition of clay fraction rather than silt concentration. Therefore, this results suggested an authentic interpretation which Jangweon series is classification as Typic Fragiochrepts.

• Journal of the Mineralogical Society of Korea
• /
• v.31 no.4
• /
• pp.267-275
• /
• 2018

The purposes of this study were to analyze the mineralogical characteristics of slaked lime used for wall repair of traditional buildings in Bagan, Myanmar and to evaluate the physical properties of lime plaster produced by the same method as Bagan region. In the X-ray diffraction and thermal analysis of the Myanmar slaked lime, portlandite ($Ca(OH)_2$) and brucite ($Mg(OH)_2$) were detected as main constituent minerals, and a carbonate rock mainly composed of dolomite ($CaMg(CO_3)_2$) minerals may be used as a raw material to make slaked lime. The field-emission scanning electron microscope analysis showed that the Myanmar slaked lime was composed of irregularly shaped crystals of $0.5{\mu}m$ or larger and a small amount of $0.1{\mu}m$ of plate - like crystals. The size and uniformity of crystals in Myanmar lime is different from that of Korea slaked lime. This may be attributed to the effect of the mineral composition and the lime hydration method of Myanmar, which produces slurry by immersing the burnt lime in excess water for a long period of time. The compressive strength of the lime plaster in Myanmar resulted in a mean value of $1.13N/mm^2$ for the specimens cured for 28 days. The strength of the specimens with Bale juice was $1.03N/mm^2$, respectively. The lime is an air setting material that exhibits strength through long carbonation process. Therefore, it is necessary to evaluate physical properties according to curing period through long-term curing over 28 days in the future.

• Economic and Environmental Geology
• /
• v.54 no.2
• /
• pp.299-308
• /
• 2021

Fe(II) released from mining activities is precipitated as various Fe(III)-oxyhydroxides when exposed to an oxidizing environment including mine drainage. Ferrihydrite, one of the representative precipitated Fe(III) minerals, is easy to adsorb heavy metals and other pollutants due to the large specific surface area caused by very low crystallinity. Ferrihydrite is transformed to thermodynamically more stable goethite in the natural environment. Hence, information on the transformation of ferrihydrite to goethite and the related mobility of heavy metals in the acid mine drainage is important to predict the behaviors of those elements during ferrihydrite to goethite transition. The behaviors of heavy metals during the transformation of ferrihydrite to goethite were investigated for core samples collected from an AMD treatment system in the Heungjin-Taemaek coal mine by using X-ray diffraction (XRD), chemical analysis, and statistical analysis. XRD results showed that ferrihydrite gradually transformed to goethite from the top to the bottom of the core samples. Chemical analysis showed that the relative concentration of As was significantly high in the core samples compared with that in the drainage, indicating that As was likely to be adsorbed strongly on or coprecipitated with iron oxyhydroxide. Correlation analysis also indicated that As can be easily removed from mine drainage during iron mineral precipitation due to its high affinity to Fe. The concentration ratio of As, Cd, Co, Ni, and Zn to Fe generally decreased with depth in the core samples, suggesting that mineral transformation can increase those concentrations in the drainage. In contrast, the concentration ratio of Cr to Fe increased with depth, which can be explained by the chemical bond of iron oxide and chromate, and surface charge of ferrihydrite and goethite.

• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.4
• /
• pp.427-437
• /
• 2020

Manganese nodules, which are evaluated as potential metal resources, have been found in the Arctic Ocean as well as in the abyssal plains of the Pacific and Indian Oceans. Manganese nodules exhibit strong variations in the morphology, internal texture, chemical composition and mineralogy as they grow. The relationship between the texture and chemical elemental composition during the growth process is well documented, but the mineral composition variation during the growth process is not. Because the manganese oxide minerals in nodules are fine-grained and poorly crystalline, quantitative analysis for the mineral composition is challenging for the bulk nodule sample. This study investigated the internal texture and Mn-oxide mineral composition of manganese nodules obtained from the East Siberian Sea. Semi-quantitative analysis was attempted for three main Mn-oxide minerals constituting the manganese nodules (i.e., todorokite, buserite and birnessite) using the peak area ratio of X-ray diffraction analysis graphs. In the East Siberian Sea manganese nodules, birnessite is more abundant than buserite or todorokite, and no correlation is found between the mineral composition and the internal texture. Instead a correlation is found between the relative content of todorokite and the lamellae depth. The todorokite content tends to increase from the surface to the core of the nodules, which can be attributed to a recrystallization process or difference in the growth rate within the nodule. This study shows that semi-quantitative analysis of manganese oxide minerals using the peak area ratio is useful in the mineralogical study of manganese nodules.

• Applied Chemistry for Engineering
• /
• v.22 no.6
• /
• pp.685-690
• /
• 2011

In this study, a solvothermal reaction to prepare nanocrystalline titania was carried out using $TiCl_4$ and mixed solvents of alcohol and water. The effects of the type and the composition of alcohol on the crystal structure and agglomeration of final $TiO_2$ products were investigated. The products were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) as well as scanning electron microscopy (SEM). In the solvothermal reaction using the n-butanol solutions with different volume ratios of n-butanol/water (100/0, 75/25, 50/50, 25/75, 0/100), the extent of agglomeration of obtained rutile $TiO_2$ was found to change with the volume ratio of n-butanol/water, and the n-butanol/water ratio of 75/25 revealed the best result for the preparation of well-dispersed nanocrystalline $TiO_2$ powders. The crystal phase of $TiO_2$ prepared through the solvothermal reaction changed with the type of alcohol in solvent (alcohol/water = 75/25). $TiO_2$ products obtained with the aqueous solutions of methanol, ethanol and isopropanol have an anatase phase, while that with n-butanol has a rutile phase. The results showed that, in the solvothermal reaction using both $TiCl_4$ as a starting material and the alcohol-water mixed solvents without any other additive, the enhancement of dispersion and control of crystal structure of $TiO_2$ products can be feasible by simply varying the composition and type of alcohol in the mixed solvents.