• 대한금속재료학회지
• /
• 제46권2호
• /
• pp.88-96
• /
• 2008

Thermal evaporated 10 nm-$Ni_{50}Co_{50}$/(70 nm-poly)Si films were deposited to examine the energy saving properties of silicides formed by rapid thermal annealing at temperature ranging from 500 to $1,100^{\circ}C$ for 40 seconds. Thermal evaporated 10 nm-Ni/(70 nm-poly)Si films were also deposited as a reference using the same method for depositing the 10 nm-$Ni_{50}Co_{50}$/(70 nm-poly)Si films. A four-point probe was used to examine the sheet resistance. Transmission electron microscopy (TEM) and X-ray diffraction XRD were used to determine cross sectional microstructure and phase changes, respectively. UV-VIS-NIR and FT-IR (Fourier transform infrared spectroscopy) were used to examine the near-infrared (NIR) and middle-infrared (MIR) absorbance. TEM analysis confirmed that the uniform nickel-cobalt composite silicide layers approximately 21 to 55 nm in thickness had formed on the single and polycrystalline silicon substrates as well as on the 25 to 100 nm thick nickel silicide layers. In particular, nickel-cobalt composite silicides showed a low sheet resistance, even after rapid annealing at $1,100^{\circ}C$. Nickel-cobalt composite silicide and nickel silicide films on the single silicon substrates showed similar absorbance in the near-IR region, while those on the polycrystalline silicon substrates showed excellent absorbance until the 1,750 nm region. Silicides on polycrystalline substrates showed high absorbance in the middle IR region. Nickel-cobalt composite silicides on the poly-Si substrates annealed at $1,000^{\circ}C$ superior IR absorption on both NIR and MIR region. These results suggest that the newly proposed $Ni_{50}Co_{50}$ composite silicides may be suitable for applications of IR absorption coatings.

• 대한금속재료학회지
• /
• 제47권9호
• /
• pp.586-590
• /
• 2009

The effects of additives on the surface morphology and physical properties of copper electrodeposited on polyimide(PI) film were investigated here. Two kinds of additives, an activator(additive A) and a leveler(additive B),were used in this study. Electrochemical experiments, in conjunction with scanning electron microscopy(SEM), X-ray diffraction(XRD) and a four-point probe, were performed to characterize the morphology and mechanical characteristics of copper electrodeposited in the presence of the additives. The surface roughness, crystal growth orientation and resistivity could be controlled using various quantities of additive B. High resistivity and lower peel strength were observed on the surface of the copper layer electroplated onto the electrolyte with no additive B. However, a uniform surface, lower resistivity and high flexibility were obtained with a combination of 20 ppm of additive A and 100 ppm of additive B.

• 대한금속재료학회지
• /
• 제47권8호
• /
• pp.508-515
• /
• 2009

Ti-6Al-4V biomaterial is widely used as a bone alternative. However, Ti-6Al-4V ELI alloy suffers from numerous problems such as a high elastic modulus and high toxicity. Therefore, non-toxic biomaterials with low elastic moduli need to be developed. Ti-HA(hydroxyapatite) composites were fabricated in the present work by pulsed current activated sintering (PCAS) at $1000^{\circ}C$ under 60 MPa using mixed Ti and HA powders. The effects of HA content on the physical and mechanical properties of the sintered Ti-HA composites have been investigated. X-ray diffraction(XRD) analysis of the Ti-HA composites, including Ti-40 wt%HA in particular, revealed new phases, $Ti_{2}O$, CaO, $CaTiO_3$, and TixPy, formed by chemical reactions between Ti and HA during sintering. The hardness of the Ti-HA composites decreased with an increase in HA content. The corrosion resistance of these composites was observed to be an excellent candidate as a commercial Ti-6Al-4 V ELI alloy. A Ti-5 wt%HA composite fabricated by PCAS is recommended as a new biomaterial, because it offers good corrosion resistance, compressive strength, wear resistance, and biocompatibility, and a low Young's modulus.

• 대한금속재료학회지
• /
• 제49권1호
• /
• pp.25-31
• /
• 2011

Solid oxide fuel cells (SOFCs) have many attractive features for widespread applications in generation systems. Recently, stainless steels have attractive materials for metallic bipolar plate because metallic bipolar plates have many benefits compared to others such as graphite and composite bipolar plates. SOFC operates on high temperature of about $800{\sim}1000^{\circ}C$ than other fuel cell systems. Thus, many studies have attempted to reduced the operation temperature of SOFC to about $600{\sim}800^{\circ}C$, which is the intermediate temperature (IT) of SOFC. Low cost and high-temperature corrosion resistance are very important for the practical applications of SOFC in various industries. In this study, two specimens, 304 and 430 stainless steels with and without different pre-surface treatments on the surface were investigated. And, specimens were exposed at high temperature in the box furnace under oxidation atmosphere of $800^{\circ}C$. Oxidation behavior have been investigated with the materials exposed at different times (100 hrs and 400 hrs) by SEM, EDS and XRD. By increasing exposure time, the amount of metal oxide increased in the order like; STS304 < STS430 and As-received < As-polished < Sand-blast specimens.

• Composites Research
• /
• 제34권1호
• /
• pp.23-29
• /
• 2021

탄소섬유는 단위 중량 당 높은 강도 및 모듈러스를 갖기 때문에 고성능 복합 재료 제조 시 탄소보강재로 많이 사용된다. 그러나 탄소 섬유를 제조하는 공정에서 많은 시간과 높은 에너지를 소모하여 제조비용이 크게 증가하기 때문에 상용화에 어려움을 겪고 있다. 따라서 생산 비용 절감을 위하여 제조 공정에 사용되는 에너지를 대체할 수 있는 고속의 저 에너지원을 적극적으로 찾아 연구할 필요가 높아졌다. 폴리아크릴로니트릴(PAN) 전구체(Precursor)로 상용화 된 탄소 섬유는 180~300℃의 대기 분위기에서 안정화 과정이 이루어지고, 1600℃ 이하의 불활성 가스 분위기에서 탄화하여 탄소 섬유를 생산할 수 있다. 이 두 공정은 많은 시간과 높은 에너지를 사용하지만, 고성능 탄소 섬유를 생산하는 데 필수적이며 중요하다. 따라서 최근에는 공정 시간을 단축하고 에너지 소비를 줄일 수 있는 플라즈마, 전자 빔 및 마이크로파와 같은 다양한 다른 에너지원을 보조적으로 사용 함으로써 저 에너지·고속 안정화 공정 기술이 시도되고 있다. 본 연구에서는 플라즈마 공정과 열처리를 연속적으로 수행하여 PAN 전구체 안정화 공정을 연구하였으며, 모폴로지, 구조적 변화, 열적 및 물리적 특성 변화를 연구하였다.

• Journal of Electrochemical Science and Technology
• /
• 제12권1호
• /
• pp.112-125
• /
• 2021

The new emerging "High entropy materials" attract the attention of the scientific society because of their simpler structure and spectacular applications in many fields. A novel nanocrystalline high entropy (Be,Mg,Ca,Sr,Zn,Ni)3O4 oxide has been successfully synthesized through mechanochemical treatment followed by sintering and air quenching. The present research work focuses on the possibility of single-phase formation in the aforementioned high entropy oxide despite the great difference in the atomic sizes of reactant alkaline earth and 3d transition metal oxides. Structural properties of (Be,Mg,Ca,Sr,Zn,Ni)3O4 high entropy oxide were explored by confirmation of its single-phase Fd-3m spinel structure by x-ray diffraction (XRD). Further, nanocrystalline nature and morphology were analyzed by scanning electron microscopy (SEM). Among thermal properties, thermogravimetric analysis (TGA) revealed that the (Be,Mg,Ca,Sr,Zn,Ni)3O4 high entropy oxide is thermally stable up to a temperature of 1200℃. Whereas phase evolution in (Be,Mg,Ca,Sr,Zn,Ni)3O4 high entropy oxide before and after sintering was analyzed through differential scanning calorimetry (DSC). Electrochemical studies of (Be,Mg,Ca,Sr,Zn,Ni)3O4 high entropy oxide consists of a comparison of thermodynamic and kinetic parameters of water and hydrazine hydrate oxidation. Values of activation energy for water oxidation (9.31 kJ mol-1) and hydrazine hydrate oxidation (13.93 kJ mol-1) reveal that (Be,Mg,Ca,Sr,Zn,Ni)3O4 high entropy oxide is catalytically more active towards water oxidation as compared to that of hydrazine hydrate oxidation. Electrochemical impedance spectroscopy is also performed to get insight into the kinetics of both types of reactions.

• Advances in nano research
• /
• 제10권2호
• /
• pp.191-210
• /
• 2021

To compare the antifungal effect of two nanomaterials (NMs), nanoparticles of zinc oxide were synthesized by a chemical route and zinc oxide-based nanobiohybrids were obtained using green synthesis in an extract of garlic (Allium sativum). The techniques of X-Ray Diffraction (XRD), Infrared (IR) and Ultraviolet Visible (UV-Vis) absorption spectroscopies and Scanning (SEM) and Transmission Electron Microscopies (TEM) were used to determine the characteristics of the nanomaterials synthesized. The results showed that the samples obtained were of nanometric size (< 100 nm). To compare their antifungal capacity, their effect on Cercospora sp. was evaluated. Test results showed that both nanomaterials had an antifungal capacity. The nanobiohybrids (green route) gave an inhibition of fungal growth of ~72.4% while with the ZnO-NPs (chemical route), inhibition was ~87.1%. Microstructural studies using High Resolution Optical Microscopy (HROM) and ultra-structural analysis using TEM carried out on the treated strains demonstrated the effect of the nanofungicides on the vegetative and reproductive structures, as well as on their cell wall. To account for the antifungal effect presented by ZnO-NPs and ZnO nanobiohybrids on the fungi tested, effects reported in the literature related to the action of nanomaterials on biological entities were considered. Specifically, we discuss the electrical interaction of the ZnO-NPs with the cell membrane and the biomolecules (proteins) present in the fungi, taking into account the n-type nature of the ZnO semiconductor and the electrical behavior of the fungal cell membrane and that of the proteins that make up the protein crown.

• 한국재료학회지
• /
• 제31권6호
• /
• pp.325-330
• /
• 2021

Bi₂MoO₆ (BMO) via the structure-directing role of CO(NH₂)₂ is successfully prepared via a facile solvothermal route. The structure, morphology, and photocatalytic performance of the nanoflake BMO are characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), fluorescence spectrum analysis (PL), UV-vis spectroscopy (UV-vis) and electrochemical test. SEM images show that the size of nanoflake BMO is about 50 ~ 200 nm. PL and electrochemical analysis show that the nanoflake BMO has a lower recombination rate of photogenerated carriers than particle BMO. The photocatalytic degradation of tetracycline hydrochloride (TC) by nanoflake BMO under visible light is investigated. The results show that the nanoflake BMO-3 has the highest degradation efficiency under visible light, and the degradation efficiency reached 75 % within 120 min, attributed to the unique hierarchical structure, efficient carrier separation and sufficient free radicals to generate active center synergies. The photocatalytic reaction mechanism of TC degradation on the nanoflake BMO is proposed.

• 한국표면공학회지
• /
• 제54권4호
• /
• pp.178-183
• /
• 2021

The temperature and frequency dependence of the dielectric constant of the BaTiO₃ substituted with two types of donor dopants, Nb⁵⁺ and Ta⁵⁺, respectively, were compared and analyzed. Dielectric specimens of four specific compositions, Ba_0.95Nb_0.05TiO₃, Ba_0.90Nb_0.10TiO₃, Ba_0.95Ta_0.05TiO₃, and Ba_0.90Ta_0.010TiO₃ were prepared by calcining at 1100 ℃ and sintering at 1300 ℃ to have a perovskite structure to measure capacitance. XRD and SEM analysis were used to observe the structure, with particular focus on the integration into the Nb⁵⁺ and Ta⁵⁺ substituted BaTiO₃ crystal lattice. X-ray diffraction peaks in the (200) and (002) planes were observed between 45.10° and 45.45° of the BaTiO₃ solid solution substituted with different fractions of Nb⁵⁺ and Ta⁵⁺. The dielectric properties were analyzed and the relationship between the properties and structure of the substituted BaTiO₃ was established. The fine particles and high density of the substituted BaTiO₃ were maintained like pure BaTiO₃, and in particular, a shift toward the low temperature side of the phase transition temperature range was clearly found, unlike pure BaTiO₃. In addition, the phase transition at a temperature higher than the Curie temperature relatively satisfies the modified Curie-Weiss law.

• 한국재료학회지
• /
• 제31권11호
• /
• pp.593-600
• /
• 2021

Herein, a series of g-C₃N₄ modified Bi₂MoO₆ nanocomposites using Bi₂MoO₆ and melamine as original materials are fabricated via sintering process. For presynthesis of Bi₂MoO₆ an ultrasonic-assisted hydrothermal technique is researched. The structure and composition of the nanocomposites are characterized by Raman spectroscopy, X-ray diffraction (XRD), and high-resolution field emission scanning electron microscopy (SEM). The improved photoelectrochemical properties are studied by photocurrent density, EIS, and amperometric i-t curve analysis. It is found that the structure of Bi₂MoO₆ nanoparticles remains intact, with good dispersion status. The as-prepared g-C₃N₄/Bi₂MoO₆ nanocomposites (BMC 5-9) are selected and investigated by SEM analysis, which inhibits special morphology consisting of Bi₂MoO₆ nanoparticles and some g-C₃N₄ nanosheets. The introduction of small sized g-C₃N₄ nanosheets in sample BMC 9 is effective to improve the charge separation and transfer efficiency, resulting in enhancing of the photoelectric behavior of Bi₂MoO₆. The improved photoelectronic behavior of g-C₃N₄/Bi₂MoO₆ may be attributed to enhanced charge separation efficiency, photocurrent stability, and fast electron transport pathways for some energy applications.