• Journal of Animal Environmental Science
• /
• v.5 no.1
• /
• pp.17-22
• /
• 1999

This experiment was conducted to determine the influence of litter type on growing performance of broiler and litter characteristics. Sawdust, wood chips and solid part of cattle manure was used as a litter from 7 to 42 days of broiler age. The body weight was significantly (p<.05) higher in manure solid than those of sawdust and wood chips. The litter production was 2,134, 2,246 and 1,785g per bird on the sawdust, the wood chip and the manure solid during 35 days, respectively. Although the initial moisture contents of the litter materials were different 23.5% for sawdust, 16.26% for wood chips and 61.57% for cattle manure solids, the moisture were different 23.5% for sawdust, 16.26% for wood chips and 61.57% for cattle manure solid, the moisture contents became similar after 28 days of the experimental period. The nitrogen content of manure solid was higher than those of sawdust and wood chips. It was concluded that solid part of cattle manure and wood chips were potentially useful source of litter materials for broiler.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.2
• /
• pp.23-28
• /
• 2007

Wood fuel must be dried before combustion to minimize the energy loss. Sawdust of Japanese red pine was dried in a direct contact thermal screw dryer to investigate the drying characteristics of sawdust as a raw material for bio-fuel. Average drying rate and energy efficiency was 1.4%/min and 69.23% at $100^{\circ}C$, respectively, and those at $120^{\circ}C$ was 2.1%/min and 71.03%, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.3
• /
• pp.109-115
• /
• 2002

Mycelial growth of L. edodes by pretreatments of softwood was studied on a sawdust medium. The sawdust used was from the following softwood species : Larix leptolepis, Pinus densiflora and Pinus koraiensis. The pretreatment consisted of cold-water (48 h), hot-water (3 h) and steam extractions (3 h) at a ratio of 500 g : 3,000 mL (sawdust : distilled water). The sawdust medium was a mixture of 76% sawdust, 20% rice bran, 3% glucose, 0.4% potassium nitrate and 0.6% calcium carbonate. Following sawdust pretreatments proved most suitable : L. leptolepis (steam extraction), P. densiflora (hot-water extraction) and P. koraiensis (hot-water extraction). Mycelial growth on P. koraiensis sawdust increased in proportion to an increase in hot-water extraction time. Mycelial growth was optimum on the sawdust extracted for 12 hours, hot-water extraction beyond this period proved unsuitable. With the exception of P. densiflora at 100 ㎍/mL, antifungal activity occurred in every sample. Maximum inhibition of mycelial growth was obtained from following concentration of hot-water extractives : P. densiflora (10⁴ ㎍/mL) and P. koraiensis (10⁴ ㎍/mL). This study has provided useful preliminary information for the cultivation of L. edodes.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.1
• /
• pp.110-123
• /
• 2019

This work was conducted to examine the relationship between lignin content and the durability of larch (LAR) pellets. LAR sawdust was immersed in tap water (TW), sulfuric acid (AC) and sodium hydroxide (AK) solutions, and then the immersed sawdust was used for pellet fabrication. Klason lignin (KL) content of the immersed LAR, contents of soluble lignin (SL) and monomeric sugars liberated from the immersion of LAR, and durability of LAR pellets were measured. KL content decreased as the concentration of AC and AK solutions increased, but glucose content increased with increase in AC and AK concentration. Durability of wood pellets fabricated using non-immersed LAR sawdust was the highest, followed by those made using TW-, AK- and AC-immersed sawdust. LAR pellets became more durable as the concentration of KL and SL increased, but a significant positive correlation was found only between pellet durability and KL content. Through the fluorescent microscopic observation and SEM-EDX analysis, it was verified that lignin content of non-immersed LAR pellets was higher than that of AC- and AK-immersed LAR pellets. These results suggest that lignin might contribute to an increase in inter-particle bonding in wood pellets.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.6
• /
• pp.60-66
• /
• 2003

Mycelial growth of L. edodes by supplement nutrition of softwood was studied on a sawdust medium. The sawdust used was from the following softwood species : Larix leptolepis, Pinus densiflora and Pinus koraiensis. The added nutritions consisted of carbon nutritions(sucrose, active carbon, xylose, glucose, paper pellet), nitrogen nutritions(potassium nitrate, ammonium chloride, asparagine, glutamic acid) and vegetable oil(rice bran oil). The sawdust medium was a mixture of 76% sawdust, 20% rice bran, 3% carbon nutrition, 0.4% nitrogen nutrition and 0.6% calcium carbonate. Following addition of carbon and nitrogen nutritions on the sawdust medium proved most suitable : L. leptolepis (glucose, glutamic acid), P. densiflora (active carbon, asparagine) and P. koraiensis (xylose, glutamic acid). The highest mycelial growth was obtained from sawdust medium of optimum condition with 97% of L. leptolepis, 110% of P. densiflora and 98% of P. koraiensis. This study has provided useful preliminary information for the cultivation of L. edodes.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.3
• /
• pp.3-26
• /
• 1985

The object of this study was to investigate the effects on physical and mechanical properties of wood particle and sawdust board combined with wire net. Conventional forming, press-lam, and veneer comply boards combining one to four wire net sheets were made from wood particle and sawdust with different spacings (8, 10, 12, and 18 Mok) and different wire diameters (0.35, 0.50, and 0.80mm) composing wire net. They were compared and analyzed statistically with specific gravity, thickness swelling, length swelling, bending properties (modulus of rupture, modulus of elasticity, work to proportional limit, and total work), internal bonding strength, and screw holding strength between wood particle and sawdust boards. The results obtained at this study as cording to the discussions might be concluded as follows; 1. In specific gravity, both particle and sawdust boards by press-lam method were higher than by conventional forming and veneer comply method, and the boards containing more wire net sheets also showed higher value. But the wire net spacings(Mok) had no influence on specific gravity. In general, particle board showed higher specific gravity than sawdust board. Veneer comply board showed lowest specific gravity values. 2. Both particle and sawdust boards by press-lam method was slightly lower than by conventional forming and veneer comply method in thickness swelling. The sawdust board containing 8, 12. and 18 Mok wire net showed lower thickness swelling than the corresponding particle board, but both sawdust and particle boards containing the T8 and 10 Mok wire net showed higher and similar thickness swelling. 3. Both particle and sawdust boards containing wire net showed no difference in MOR and MOE of bending. Comply board was the highest and particle board showed slightly higher than sawdust board in MOR and MOE values. 4. In work to proportional limit and total work in bending, both particle and sawdust boards containing thicker wire diameter and more wire net sheets showed higher value. From these facts, it is conceivable that boards with thicker wire diameter and more wire net sheets show increasing resistance against external force. But there was no significant difference between particle and sawdust borads. 5. In resistance against delamination (internal bonding strength), both sawdust and particle boards containing wire net showed lower value than control, and also showed decreasing tendency with more number of wire net sheet composed. Particle board showed higher resistance against delamination than sawdust board. 6. In screw holding strength, sawdust board containing thicker wire diameter and more wire net sheets showed higher value, but particle board by press-lam method was higher than by conventional forming and veneer comply method. Screw holding strength of particle board was higher than that of sawdust board.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.2
• /
• pp.30-36
• /
• 2006

Wood fuel must be dried before combustion to minimize the energy loss. Sawdust of Japanese red pine was dried in a batch type fluidized-bed to investigate the drying characteristics of sawdust as a raw material for bio-fuel. The minimum fluidization air velocity was increased as particle size was increased. It took about 21 minutes and 8 minutes to dry 0.08 m-deep bed of particles with average particle size of 1.3 mm from 100% to 10% moisture content at air temperature of $20^{\circ}C$ and $50^{\circ}C$, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.1
• /
• pp.36-42
• /
• 2010

This study has been carried out to investigate the characteristics of pellets manufactured from sawdust, and a mixture of liquid wood-tar and sawdust. Pellets were prepared at room temperature under 2000 kgf/$cm^2$ using an universal testing machine. The pellets prepared from Q. variabilis wood had slightly higher density than those prepared from P. densiflora wood. The amount of fine particles from Q. variabilis wood pellets was smaller than those from P. densiflora wood. The pellets from P. densiflora wood had higher heating values than those from Q. variabilis wood. The wood pellets manufactured with wood tar showed higher moisture content, density and heating value, but lower fine particles. From the experimental results, it is suggested that wood tar can be used to obtain the higher quality wood pellets.

• Composites Research
• /
• v.31 no.5
• /
• pp.202-208
• /
• 2018

In this paper, mechanical and hygroscopic properties of teak sawdust and recycled polypropylene (RPP) composites are evaluated and compared with virgin polypropylene (VPP) matrix based composites. Verities of composites are prepared by variation in the plastic types, wood plastic ratio and the addition of coupling agent in the formulations. Mixing of wood sawdust and polypropylene is done by a twin screw extruder, and then sheets of wood plastic composites (WPCs) are produced by using the compression molding method. The results show that recycled matrix composites exhibit better tensile, flexural strength with low impact strength than virgin matrix based composites. Recycled composites show low water absorption and thickness of swelling than virgin matrix based composites. The results confirm that wood content in the polymer matrix affects the performance of composites while presence maleated polypropylene (MAPP) improves the properties of the composites significantly. Developed RPP matrix composites are as useful as VPP matrix composites and have the potential to replace the wood and plastics products without any adverse effect of the plastics on the environment.

• The Korean Journal of Mycology
• /
• v.44 no.2
• /
• pp.100-102
• /
• 2016

Ergothioneine is a natural compound with strong antioxidant properties. In this study, the effects of different nitrogen sources including ammonium nitrate, ammonium sulfate, sodium nitrate, and histidine in sawdust media were investigated to enhance ergothioneine contents in Shiitake (Lentinula edodes) fruit bodies. The addition of 0.2% ammonium sulfate in the growth media showed the highest enhancement of ergothioneine content in shiitake fruit bodies which was 1.7-fold higher than the control. On the other hand, histidine, a building block of ergothioneine decreased the concentration of ergothioneine significantly. Our results demonstrate that the cultivation of shiitake in sawdust media with suitable nutrients was effective to enhance its ergothioneine contents.