• Journal of the Korean Wood Science and Technology
• /
• v.51 no.1
• /
• pp.14-22
• /
• 2023

Economical use of larix (larch) boards (grade 3) in industries is lower than that of imported hardwood; thus, studies have been conducted toward performance improvement of larix boards. Herein, flexural modulus of larix board samples laminated with wood adhesives polyurethane resins, poly (vinyl acetate) resins, phenol-resorcinol-formaldehyde resins, melamine-formaldehyde resins, and urea-formaldehyde resins was compared with that of the samples bonded with adhesives reinforced with mesh-type basalt fibers. Moreover, the flexural moduli of the laminated samples bonded by mesh-type basalt fibers were compared with those of reinforced samples. The results showed that boards laminated with polyurethane and urea-formaldehyde resin adhesives had higher flexural modulus than those without the lamination. In particular, the increase in the flexural modulus was relatively significant for the 2- and 3-ply board structures laminated with polyurethane adhesives compared to those with reinforcement. The 3-ply board structure without reinforcement had the highest flexural modulus when the urea-formaldehyde resin adhesive was used.

• Journal of the Korean Wood Science and Technology
• /
• v.16 no.4
• /
• pp.3-9
• /
• 1988

Infrared (IR) spectroscopic techniques for the analysis of wood samples and the absorbance spectra of solid woods were presented. KBr pellets were prepared by throughly mixing approximately 300 mg of dried KBr and 1 mg of finely milled wood powder extracted with ethanol-cyclohexane previously. This mixture was made into a transparent disc by means of a pellet-making die (10 ton/$cm^2$ for 10 min). This IR techniques were applied for the analysis of archaeological wood samples. The most notable difference in the IR spectra between the recent and the archaeological waterlogged woods is that the absorption band centered at $1,730cm^{-1}$ was significantly diminished in the waterlogged ones. Total loss of absorption in $1,730cm^{-1}$ might be mainly due to the result of hemicellulose degradation. Another feature indicated by IR spectral comparision are that the degraded waterlogged wood samples showed 1) the increased intensity of the 1,600, 1,500 and $1,270cm^{-1}$ due to the residual lignin and the increased intensity at 1,470 and $1,425cm^{-1}$ due to the degradation of hemicellulose and 2) to the emergence of single band around $1,050cm^{-1}$ instead of three bands at 1,110, 1,060 and $1,040cm^{-1}$ in recent wood due to the degradation of cellulose crystalline. It was revealed from the IR examinations that the first change of wood in the waterlogged situation was the lysis of hemicellulose and the second the lysis of cellulose. It was also suggested that IR spectroscopy could serve a fast method for the investigation on the chemical characteristics of archaeological wood samples.

• Journal of the Korean Wood Science and Technology
• /
• v.23 no.3
• /
• pp.66-72
• /
• 1995

The rate of fixation of the components were evaluated in CCA-Type B and CCFZ-treated radiata pine sapwood by quantitative analysis of solution expressed from the treated wood. The leaching characteristics of radiata pine blocks treated with CCA-Type B and CCFZ were also evaluated by the AWPA standard leaching test. Both fixation and leaching charactersistics of CCA-Type B were compared with CCA-Type C treated wood samples. The rate of CCA-Type B fixation was a little faster than that of CCFZ. However, significant amounts of arsenic was unfixed in the CCA-Type B treated samples and consequently leached. These significant quantities of arsenic liberated from the CCA-Type B treated wood during service may pose some environmental concerns. Arsenic was no longer detectable from CCA-Type C treated samples when fixation was complete, even though the fixation of CCA-Type C was slower in some degree than CCA-Type B. In summary, it could be said that CCFZ was much safer preservative than CCA-Type B by the criterion based on the relative hazard assessed by absolute amount of unfixed element present in the treated wood. Also the decision that CCA preservative has to move from Type B to Type C should be made sooner or later for continuous use of CCA preservative in the future.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.4
• /
• pp.17-22
• /
• 2002

A wooden coffin estimated to be made in Baikjae Dynasty in AD. 6 century was excavated from ancient tombs in Nung-san ri, and examined to identify its wood species using light and electron microscopy. Wooden part attached to oxdized complex around the iron nails on the coffin was electro-chemically separated to prepare the samples for observation. The results revealed that 24 samples out of 28 samples investigated were identified as Torreya nucifera, while the rest 4 samples were identified as Pinus densiflora.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.1
• /
• pp.52-60
• /
• 2006

This study investigated how wood properties (i.e., annual rings, sapwood, heartwood, and cracks) might affect preservative treatment in Japanese larch (Larix leptolepis) round-wood product. We specially focused on small-diameter (~10 cm diameter) wood that is commercially sold in market. Among 100 wood samples, the groups of sample with 13~16, 17~20 annual rings represented 33 and 27 in each frequency, while 2~3 and 4~5 mm annual ring width accounted for 72 and 68 in frequency. More than a half (54%) of wood samples contained a mix of heartwood and sapwood in its surface. The rest (46%) had only heartwood exposed in the wood surface. A wide range of checks were showed in the wood samples, but the highest frequency was observed in samples with 1~6 surface (1~14 mm in size) checks and 1~4 end-grain (8~14 mm in size) checks in each round-wood sample. Pressure treatment resulted in a wide range of penetration of ACQ (Alkaline Copper Quat) into the wood, showing $4.3{\pm}4.19mm$ penetration in the wood samples contained a mix of heartwood and sapwood in its surface. However preservative treatment was much less effective for the heartwood only wood samples, ranging average 1.3 mm with ACQ and 1.1 mm with CCA (Chromated Copper Arsenate). These penetration results shown in heartwood samples did not meet the penetration standard that is required for H3 by the Korean Forest Service in relation to wood preservation treatment. These low penetration results were not significantly improved even if we incised wood samples to improve treatment effect, showing only small increase of 0.7 mm with ACQ and 0.6 mm with CCA. When preservative treatment was tested with heartwood, penetration of preservatives decrease with increase of annual rings per a cross-section area (r=0.5345). We also found that the length and number of check had no effect on preservative treatment, showing r=0.1301 and r=0.1802, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.20 no.3
• /
• pp.55-60
• /
• 1992

Japanese red pine (Pinus densiflora S. et. Z.) decayed by brown-rot fungi Tyromyces palustris and Gloeophyllum trabeum were subjected to X-ray diffraction analysis and infrared spectral examinations. Pine woods decayed by T. palustris showed the increase of relative crystallinity in the initial stage of degradation. When the weight loss was above 30%, then the crystallinity went down slowly. In contrast, the wood samples degraded by G. trabeum showed the decrease of crystallinity from the beginning stage of decay. The changes of crystallinity in brown-rotted woods suggested that the degradation rate of crystalline cellulose was varied with the brown rot fungal species. X-ray diffraction analyses also indicated that crystalline cellulose was much more slowly broken down than the amorphous one. The most notable difference in the IR spectra of the brown-rotted wood samples was that the adsorption band centered at 1,730$cm^{-1}$ was significantly diminished in the decayed wood. indicating the degradation of hemicellulose by brown-rot fungi. However, no marked changes of intensities at 1,000, 1,060 and 1,040$cm^{-1}$ were observed in the brown rotted wood samples, suggesting that crystal line cellulose was resistant against the attack by brown rot fungi.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.5
• /
• pp.46-57
• /
• 2007

The leachability of boron in zinc borate (ZB)-modified oriented strandboard (OSB) from southern wood species was investigated in this study. The leaching experiments were conducted by exposing edge-sealed OSB samples under running water at $31^{\circ}C$ for 8, 24, 72, and 216 h. The results from leached samples were compared with those from the unleached controls. Boron leaching of the modified OSB occurred upon the initial water exposure, and the leaching rate decreased as the leaching time increased. Initial boric acid equivalent (BAE) level, wood species, and sample thickness swelling significantly influenced the leachability. There was no consistent effect of polyethylene glycol (PEG) on zinc borate leaching. The glue-line washing within OSB due to thickness swelling of the test samples under water and decomposition of the borate to form water-soluble boric acid were thought to be two possible causes for the observed leaching. The relationship between assayed BAE and leaching time followed a decaying exponential function for zinc borate treated OSB. From the boron/zinc ratio after each leaching period, boron element in ZB was more or less leachable. The material constant of the regression models allowed comparing the leachability of the modified OSB for various wood species. An unified leaching method for treated wood composite materials is needed.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.3
• /
• pp.35-41
• /
• 2003

The mechanical and physical properties of wood are strongly dependent upon the slope of grain. Specially, tensile strength is more severely affected by the slope of grain. Therefore, tension tests were performed on small thin wood samples made from Pinus radiata with varying the slope of grain. Determining the tensile strength for clear thin wood samples the other variabilities associated with material, size, drying, defects, etc were discarded. Slope of grain was measured by the slope of grain indicator and actual slope of grain was also determined by a protractor. Correlation coefficients between machine measured and actual slope of grain for 40 pieces of 2×20 mm, 300 mm long Pinus radiata were 0.84 for wide face measurement. Results also showed that tensile strength and MOE from stress wave tests decreased with increasing the slope of grain. This study did not establish a relationships for tensile strength and MOE from stress wave with slope of grain. However, the trends of MOEs from stress wave test with both slope of grain are agreed well with Hankinson's equation. Predicted tension strength curve by Hankinson's equation was also agreed well with the experimental data over the range from 0 to 13 degrees for slope of grain.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.3
• /
• pp.173-182
• /
• 2023

Color is an attribute of visual perception and can be an important factor that affects the preference of customers toward bamboo and wood products. Solar radiation can discolor bamboo surfaces and initiate cracking. The purpose of this study is to investigate the effects of an ultraviolet (UV)-protective coating on the photodiscoloration of untreated and heat-treated Phyllostachys bambusoides bamboo surfaces. Artificial UVA radiators are set at a UVA irradiance of 2,000 W/m² to accelerate the aging of the outer surfaces of hot-air-dried and heat-treated bamboo samples. Half of the samples are coated with transparent UV-protective paint. As the UVA radiation progresses, the discoloration prevention efficiency (DPE) of the UV-protective coating on all samples decreases gradually. The DPEs of the hot-air-dried samples are estimated to be 31.4% and 18.8% after 21 and 72 hours of artificial UVA radiation, respectively. The heat-treated samples exhibit similar trends (29.0% after 21 hours and 10.3% after 72 hours). Recoating the UV-protective paint periodically every six months is expected to minimize the discoloration of the bamboo's outer surface.

• Journal of Conservation Science
• /
• v.5 no.2 s.6
• /
• pp.3-14
• /
• 1996

The chemicals are PEG $\#4000$ and sucrose, which have been conventionally used for the treatment of waterlogged wood. The present investigation was undertaken in order to reveal difference of the impregnation between the chemicals, but also to contribute to the explanation of the chemicals penetration process and distribution within wood structure. Comparable observation concerning the deposits shapes of chemicals after treatment, PEG4000 penetrated samples were occurred at the cell wall shrinkage and cracks, whereas the majority of the cells and lumens were entirely filled with a crystalline structure. Sucrose penetrated samples remained almost like sound wood, although the penetration ristricted only the cell walls was filled by amorphous structure.