• Journal of the Korean Wood Science and Technology
• /
• v.51 no.5
• /
• pp.381-391
• /
• 2023

Densification is a technique used to improve biomass quality in wood pellet manufacturing and torrefaction treatment. In this study, the effects of torrefaction on the quality of Calliandra wood pellets were investigated, and pellets of Calliandra wood (Calliandra calothyrsus) and bark were evaluated. The study was conducted using a completely randomized design with two treatment factors, namely torrefaction temperature (250℃ and 300℃) and torrefaction duration (30, 45, and 60 min). The results showed that the interaction between temperature and torrefaction duration significantly affected the compressive strength, proximate value, and calorific value of the torrefied Calliandra wood pellets. An increase in the temperature and torrefaction duration decreased the compressive strength, moisture content, volatile matter content, and ash content of the torrefied Calliandra wood pellets. Conversely, the calorific value of Calliandra wood pellets increased with increasing temperature and torrefaction duration. The best-quality Calliandra wood pellets were produced at a torrefaction temperature and duration of 300℃ and 60 min, respectively. In terms of important quality parameters, ash content of 0.90% and calorific value of 6,303.80 cal/g were observed, which complied with the quality standards of Indonesian National Standard 8675:2018 and Deutsche Industrie Norm 51731.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.6
• /
• pp.828-841
• /
• 2016

Relatively little information is available regarding the correlation between wood and veneer quality, especially for Samama wood, an endemic wood species in eastern Indonesia. This study addresses the quality of 8 years old Samama wood and its effect on the veneer quality. Samama wood quality was determined by evaluating its specific gravity, moisture content, fiber dimensions, and microfibril angle from pith toward bark. Meanwhile, veneer quality was assessed by examining veneer thickness and lathe check characteristics. Geometry factor model was constructed to elaborate the quantities of lathe check from pith toward bark. Results show that fair variations of veneer thickness, ranging from 1.5 mm to 3.0 mm, could be obtained from Samama wood. The quantity, depth, and length of lathe check were noticeably decreasing toward bark. Further, in the same manufacturing process, geometry factor was determined as the dominant factor over other wood properties in affecting the frequency of lathe checks from pith towards bark. These facts should be put into consideration in producing veneer from Samama wood. Moreover, these results enlighten the potential of Samama wood as plywood and other excellent veneer-based products.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.4
• /
• pp.346-357
• /
• 2013

In this study, it was conducted to produce wood pellets using domestic forest thinning residues and examine their quality according to Korean pellet quality standard. Raw materials were composed of larch and mixed broad leaves species. Based on the small-end diameter (6 cm), they were classified into four different types of raw materials such as LM (larch with middle diameter), LS (larch with small diameter), MM (mixed broadleaf with middle diameter), and MS (mixed broadleaf with small diameter). After crushing and drying process, wood pellets were produced by a ring-die type pelletizer using each raw material. Wood pellets made from four different types of raw materials were tested for their quality such as calorific value, moisture content, ash content, inorganic matters and so on. As results of quality analysis, the calorific values of all wood pellets were higher than 198 kcal/kg, and satisfied with the first grade of Korea wood pellet standard. The ash content was slightly increased after pelletizing. Mechanical durability of wood pellets was highly dependent on the types of raw materials. The quality differences among wood pellets were turned out due to different physical and chemical characteristics of raw materials even though the same pelletizing condition was applied.

• Journal of the Korean Wood Science and Technology
• /
• v.47 no.5
• /
• pp.617-632
• /
• 2019

This study aimed to investigate the anatomical structure and fiber quality of four lesser-used wood species namely Benuang (O. sumatrana), Duabanga (D. moluccana), Pisang Merah (H. hellwigii), and Terap (A. odoratissimus). This study evaluated its suitability for raw material in pulp and paper manufacturing. The anatomical structure was observed macro- and microscopically. Macroscopic structures were observed directly to the wood samples, while microscopic characteristics were observed through microtome specimens. Fiber dimension was measured through macerated specimens and fiber quality was analyzed following the Rachman and Siagian's method. Results showed that these four timber species have similarity in the indistinct growth ring, diffuse porous in a radial pattern, rounded solitary vessel outline, 1 to 3 cells of ray width, deposits within the rays, fiber length, and cell wall thickness. Differences were found on vessel diameter, vessel grouping, vessel frequency, tyloses existence, type of axial parenchyma, and ray height. Based on fiber length and its derived values, the wood fibers of all species studied are suitable for pulp and paper manufacturing. They belong to the II quality class. The produced pulp and paper would have good quality, especially in tensile, folding, and tear strength. To promote their utilization, silviculture aspect of these four species has to be well understood.

• Journal of the Korean Wood Science and Technology
• /
• v.2 no.1
• /
• pp.3-18
• /
• 1974

The exports of plywood are increasing annually and it has ranked first in the world market because of the high quality product and manufactured using mordern techniques. However, it is known that the exports of the other wood products, except plywood, is inactive because of their low quality. Accordingly, to increase the exports of various wood products investigations were carried out on kiln drying techniques to improve the quality of the wood. Wet wood should be kiln dried before use to prevent various drying defects such as distortion, shrinkage etc., which would develop after processing,:and also wet wood is not suitable for cutting, gluing and finishing. Therefore, the kiln drying properties of lumber from such species as oak, ramin and meranti which are used in large quantity for manufacturing exporting wood products have been studied. The results of the research are summarized as follows. (1) The end checks and the time for drying from initial moisture content of about 40 percent to 5 percent moisture content in ovendry were investigated as follows: (2) The kiln dried results, for 30mm stock, which are presented by using kiln schedule table 3 are as follows: (3) The kiln schedules for ramin, meranti and oak are given respectively as follows: Ramin kiln schedule: Table 17 and Table 18. Meranti schedule : Table 12. Oak schedule : Table 15.

• Journal of the Korean Wood Science and Technology
• /
• v.10 no.1
• /
• pp.38-46
• /
• 1982

The research was carried out to determine the division of juvenile and adult wood from the pattern of variables of wood quality indicators, to investigate general low of the size of juwenile wood and to study the characteristics of juvenile and adult wood. For this study some trees of Pinus koraiensis were selected and several wood quality indicators such as annual ring width. late wood percentage, tracheid length tracheid diameter, wall thicknes, and microfibril angles were measured. The results of this study were summaried as follows. 1) Juvenile and adult wood can be divided into radial variations of wood quality indicators. In this study juvenile wood might be classified as a large fluctuated region of radial wood quality variations in the nearest part to pith. 2) Juvenile wood was indicated as a part of nearly cylinderical shape, averaging 6-11cm in radius, near pith. 3) Number of rings from pith of juvenile wood was about 12-20 and was nearly constant in uniform growth trees among the forest stands. 4) Usually adult wood was formed within the about 5-10m above ground.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.5 s.133
• /
• pp.50-56
• /
• 2005

The effect of wood material type on biocide retention and distribution during supercritical fluid impregnation was assessed using three different wood types including solid wood, plywood and oriented strand board (OSB). The result revealed that biocide treatability differed with structural composition and permeability of the various materials. Low treatability of plywood might be attributed to interferences of glue line limiting fluid movement. OSB samples showed higher biocide retentions, resulting from the presence of interconnecting gaps permitting more open flow.

• Journal of Korean Society for Atmospheric Environment
• /
• v.26 no.3
• /
• pp.276-285
• /
• 2010

Recently the Korean government has tried to cut down the $PM_{10}$ concentration by the Special Law for Air Quality Improvement. But the concentrations of $PM_{10}$ have exceeded the air quality standard at most monitoring stations. Primary $PM_{10}$ emitted from various sources and emission data have large uncertainty. The biomass burning is one of the major sources of $PM_{10}$ emission. The biomass burning is composed of wood stove usage, meat cooking and agricultural combustion etc.. Activity data and emission factors for the biomass burning are limited, and it is hard to calculate the air pollution emissions from these sources. In this study, we tried to estimate the air pollution emission from residential wood stove usage. The number of total wood stoves is estimated by the survey of wood stove manufacturer. And air pollution emission factors for the wood stove are investigated using the flue gas measurement by U.S. EPA particulate test method (Method 5G). As the results, the $PM_{10}$ and CO emission factors of wood stove are estimated as 7.7 g/kg-wood and 78.8 g/kg-wood respectively. The annual $PM_{10}$ and CO emissions from wood stove are calculated as 1,200~3,600 ton/year and 12,600~36,400 ton/year in Korea. It is confirmed that wood stove is the one of major sources of biomass burning, and the survey for activity data and the measurement for emission factors are needed for reducing the uncertainty of these emission data.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2004.11a
• /
• pp.80-87
• /
• 2004

• Korean Journal of Agricultural Science
• /
• v.49 no.2
• /
• pp.357-366
• /
• 2022

Biochar can be obtained by using various types of biomass under an oxygen-limited condition. Biochar can be utilized for various applications such as soil improvement, waste management, growth promotion, and adsorption. Wood vinegar is produced by the process of pyrolysis wood biomass and is used as a growth promoter, for soil improvement, and as a feed additive. When wood vinegar is treated on soil, it acts to control soil pH, improve nutrient availability, and alleviate N₂O and NH₃ volatilization. The objective of this study was to evaluate the effect of biochar and wood vinegar on the growth of perilla and soil quality. The experiment was conducted by using a Wagner pot (1·5,000 a^-1) in a glass greenhouse. The biochar was produced by pyrolysis at 450℃ for 30 minutes using rice husk and rice straw. Wood vinegar was diluted to 1 : 500 (v·v^-1) and used in this experiement. In the results of a cultivation experiment, co-application of biochar and wood vinegar enhanced the growth of perilla. In particular, rice husk biochar affected the leaves of the perilla, and rice straw biochar influenced the stems of the perilla. In addition, soil quality after treatment with biochar and wood vinegar applied together was highest compared to other units. Therefore, it is anticipated that co-application of biochar and wood vinegar will be more productive and improve soil quality compared to individual utilization of biochar and wood vinegar.