• Journal of the Korean Wood Science and Technology
• /
• v.20 no.1
• /
• pp.15-22
• /
• 1992

This study was performed to investigate the corrosion of metal fasteners in waterborne preservative-treated wood. Of all the metal tested, steel exhibited the greatest amount of corrosion across all preservatives and exposure conditions whereas stainless steel was totally inert. Galvanized steel corroded at a much lower rate compared to steel and the corrosion of brass was negligible. Among the preservatives, CCA-Type B was the most corrosive system tested. The sequence for the average corrosivity across all metals was: CCA-type B>CCA-Type C${\geq}$ACC${\geq}$CCA-Type A. Across all metals and retentions the salt formulations were more corrosive than the oxide and the corrosion was increased with the increse in the amount of preservative loadings. The amount of corrosion was also increased with the increase in exposure relative humidity (RH) across all metals and presevatives However, at the 60% RH exposure condition, the corrosion of metals was very negligible. Consequently, it can be concluded that across all metals oxide-type preservatives should be used to prevent the corrosion problem of metal fasteners in contact with treated wood and the use of steel nail preservative-treated wood should be avoided without distinction of end-use location, i.e., exterior or interior, and the use of stainless steel or at least brass nail in damp exterior condition was strongly recommended.

• Resources Recycling
• /
• v.18 no.5
• /
• pp.52-62
• /
• 2009

This research was carried out to formulate environmentally friendly wood preservatives with okara and to investigate the effects of the acid concentration used for the hydrolysis of okara and salt type on the decay resistance of the preservatives. Okara-based preservatives were formulated with okara hydrolyzates, which were prepared with 0, 1%, and 2% sulfuric acid at $25^{\circ}C$ for 1 hr, and salts such as copper chloride and/or sodium borate. The preservatives were treated into wood blocks by vacuum-pressure method, and then the treated wood blocks were leached in $70^{\circ}C$ hot water for 72 hrs. The fungal treatments of the leached wood blocks were conducted by brown-rot fungus, Tyromyces palustris, and white-rot fungus, Trametes versicolor, to examine the decay resistance of the preservatives. As the acid concentration used for hydrolysis of okara increased, the treat-ability and decay resistance of the preservatives were improved, which the leachability was decreased. Wood blocks treated with the okara/copper or okara/copper/borax, showed very good decay resistance against T. palustris and T. versicolor. However, wood blocks treated with the okara/borax and okara-free preservative solutions, were observed the fungal decay by T. palustris. The optimal conditions for the preparation of okara-based wood preservatives were formulated with okara hydrolyzed with 1% sulfuric acid, copper chloride and borax.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.3 s.131
• /
• pp.64-71
• /
• 2005

In this study, we attempted to apply ultrasonic treatment for the preservative treatment of two softwood species, Korean pine and Japanese red pines to evaluate its effectiveness. Wood samples were submerged in oilborne preservative, copper naphthenate (NCU) and waterborne preservative, alkyl ammonium compound (AAC) and then treated with ultrasonic wave of 40 kHz, 400 W. After the treatment, the retention and penetration depth of these preservatives in the specimens were measured as a function of treatment time. Both the retention and penetration depth were continuously increased with increasing the treatment time up to 120 hours, where the retention reached about 95% by the application of AAC and the penetrating depth of 95% and 83% by the application of NCU, respectively for both species. The results of electronic microscopic observation showed that the improved retention capacity could be attributed to air deflation, wood extractive deflation working of ultrasonic wavelength, and destruction of wood pits which served as the pathway of preservatives. The results suggested that the use of ultrasonic treatment could be applied to thick wood veneers for the production of laminated wood products.

• Journal of the Korean Wood Science and Technology
• /
• v.24 no.4
• /
• pp.93-99
• /
• 1996

In order to investigate the extent of fixation of new water-borne preservatives in blocks of pinus densiflora sapwoods the streaming potential through the column with preservative treated wood was measured at various conditions. The rates of leachability of ingredients in the treated wood were estimated by the measurement of electric conductivity of the solution with the leached components. The solution was also analyzed by Atomic absorption spectrophotometer (AA). As a results, the experimental data indicated that the fixation of CCB, CCFZ and ACQ in wood were relatively unstable. The fixation rates of CCB, CCFZ were improved by increasing heat and drying time. The amounts of the leached ingredients were apparently higher in CCB and CCFZ than in CCA, while the rate of leaching of ACQ was not changed at various drying temperature.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.1
• /
• pp.49-57
• /
• 2023

This research aimed to evaluate the durability of Samama (Anthocephalus macrophyllus) wood treated with boron preservatives, citric acid (CA), and heating against termites. Wood samples were impregnated firstly with 5% boron solutions, such as boric acid, borax and boric acid + borax combination at 1:1 (w/w). The second impregnation used 5% CA. The impregnations were conducted in a pressure tank at 7 kg/cm² for 4 hours. After impregnation, the samples were heat treated at 80℃ or 160℃. All the treated and control samples were exposed to decay fungi, drywood termites and subterranean termites based on SNI 7207:2014 standard. The results showed that boron preservatives reduced fungal attacks on Samama wood. The combination treatment of boric acid, CA and heat treatment at 160℃ was also effective to increase the resistance of Samama wood against white- and brown rot fungi, and drywood termites. Heat treatment consistently improved the resistance of Samama wood from decay fungi.

• 보존과학연구
• /
• s.7
• /
• pp.265-277
• /
• 1986

The degradation of wood is maimly caused by biological and thermal factor. In general, the field of wood preservation can be divided into two broadcategories; namely the deterioration, protection of wood, and the teatment of wood with preservatives. Wood in sea or brackish water incurs marine borer damage, consisting of attack by marine animal and also wood on land suffers severely from insect damage. But the largest wood degradation is caused by microorganism. Animals that attack wood in a marine environment are especially destructive in warm water-regions, little was achieved in their control recently. Therefore this manuscript only introduce the importance of wood deterioration caused by marine animal.

• Journal of the Korean Wood Science and Technology
• /
• v.38 no.4
• /
• pp.341-348
• /
• 2010

Antifungal and antibacterial activities of wood vinegars were investigated in this study in order to apply for the natural fungicides and food preservatives. The antifungal activities of wood vinegars were measured as a hyphal growth inhibition rate using four plant pathogenic, four wood rot and one mushroom pathogenic fungi. Inhibition effect on the fungi growth was explicitly observed at the concentrations higher than 0.5% of unrefined wood vinegar and higher than 1.0% of refined wood vinegar, respectively, suggesting that unrefined wood vinegars showed the higher antifungal activities than that of refined wood vinegars. The highest inhibition effect on the fungi growth was shown in Libertella betulina which is a mushroom pathogenic fungus. In addition, the wood vinegars from Pinus densiflora showed the higher antifungal activities against the plant pathogenic and wood rot fungi than that from Quercus spp.. On the other hand, the antibacterial activities of wood vinegars were determined by a paper disc method using the three gram positive and five gram negative bacteria. The unrefined wood vinegars showed a prominent effect on the suppression of bacteria growth at the concentration of 10%, while the suppression of bacteria growth was not observed in the refined wood vinegars. These results also suggest that the unrefined wood vinegars showed the higher antibacterial activities than the refined wood vinegars. The antibacterial activities of wood vinegars against gram positive bacteria were higher than those of wood vinegars against gram negative bacteria. From these results, it can be inferred that the wood vinegars has the strong antimicrobial activities and can be applied as the natural fungicides and food preservatives.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.6
• /
• pp.576-582
• /
• 2013

To obtain the basic information on wood preservative process using copper, the penetration ACQ-2 preservative agent into Douglas fir wood and its degradational characteristics were investigated. Douglas fir is known to be difficult for preservative agent injection. To find the hindrance factor of the preservatives movement, the ray height, ray density, and length of tracheid were measured and observed by a stereoscopic microscope and scanning electron microscope. The results were compared in the well-penetrated parts of preservatives and insufficient parts. There were no significant differences in height, length, and density between both parts, except for the pits of the wood elements observed in SEM micrograph. More declosed pits were found in the well-penetrated parts of preservatives. Decay characteristics of wood specimen treated with various ACQ concentrations by brown-rot fungi was observed by an optical microscope. The decayed properties of tracheid, rays, and resin canals was found in the non-treated wood specimens and it was also found that some extent of preservatives concentration is necessary to protect the decay.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.5
• /
• pp.421-425
• /
• 2009

This research investigates the effect of copper retention on copper leaching in wood treated with copper-based preservatives. Radiata pine (Pinus radiata D. Don) sapwood samples were ground in a Wiley mill equipped with a 20-mesh screen. The ground wood was vacuum-treated with various concentrations of alkaline copper quat (ACQ), bis-(N-cyclohexyl-diazeniumdioxy)-copper (CB-HDO), and copper azole (CUAZ). The treated samples were conditioned at $70^{\circ}C$ and 100% RH for 72 hours. The samples were leached by using the distilled water for four weeks, and the copper contents in each sample were measured by X-ray spectroscopy. As expected, the copper leaching was increased with increasing of copper retention. The copper leaching from the ACQ and CB-HDO treated samples were gradually decreased with increasing copper retention: however, the copper losses from the CUAZ treated samples appeared to be proportionally increased with the increase in copper retention in all retention levels tested. The results indicate that at the conditions of the same copper retention ACQ and CB-HDO treated wood have a better leaching resistance compared to CUAZ treated wood.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.5
• /
• pp.743-749
• /
• 2016

The concentration control of wood preservatives is necessary to produce a preservative treated wood having a uniform quality. Concentration measurement method of wood preservatives to be easily used in the field has not been developed yet. This study examined the way to estimate the concentration from turbidity of ACQ wood preservative that can be relatively easily measured by using a portable turbidity meter. The addition of phosphoric acid solution in an alkaline ACQ solution having a very low turbidity is created a suspension of the white substance and the turbidity suddenly increased. The optimum amount of addition of the phosphoric acid solution is until the pH of ACQ solution reaches 7, the turbidity of the ACQ solution reaches maximum value. Excessive addition of the phosphoric acid solution results in a turbidity decrease with acidification of the ACQ solution. Also ACQ solution becomes transparent. The high significance was recognized with positive correlation between the concentration and the turbidity of the ACQ solution. From the t-test, The significant difference between the actually measured concentrations and the concentrations predicted by the regression equation for industrial ACQ solutions was not recognized. Thus, it was possible to know that concentration prediction and control of industrial ACQ solution using the turbidity and a regression equation. Therefore, using the regression equation and turbidity is expected to be able to management the concentration of ACQ solution in the industrial field.