• Journal of Conservation Science
• /
• v.37 no.2
• /
• pp.135-143
• /
• 2021

Conservation treatment that involved filling the lifting parts of wooden cultural heritage is carried out by obtaining wood or wood powder of the same species and mixing it with synthetic resin or natural glue to charge the blank area. Various concentrations and mixing ratios of adhesives and additives are used, depending on the type and condition of the target. Accordingly, in this study, we determined the conditions of the filler suitable for conservation treatment of wooden sculptures with lifted or separated bark in the National Museum of Modern and Contemporary Art. The optimal filler conditions for each adhesive were selected based on drying speed, shrinkage and expansion rates, and physical deformation degree. Then, to verify their actual applicability, these fillers were applied to wood and exposed to high-humidity environment and their cross-sections were observed. The fillers showed stable application in the following order: animal glue, PVAc adhesive, acrylic adhesive. In conclusion, a 1:2 mixture of animal glue and wood powder is a suitable filler for conservation treatment of wooden sculpture with lifted bark. The results of this study suggest appropriate ways to stabilize the bark that was lifted or separated from a wooden sculpture, thus enabling the future conservation treatment of the artworks under similar conditions.

• Journal of Sericultural and Entomological Science
• /
• v.19 no.1
• /
• pp.5-7
• /
• 1977

On the purpose of exploiting cellulose resourse which is needed for artificial diet of silkworms, mulberry branch, eastern cotton wood branch, pitch pine pulp, poplar pulp, chaff, sawdust and rice straw were examined. Among the matters above mentioned. mulberry branch and pitch pine pulp were found to be replaceable as cellulose component in the artificial diet. By means of some chemical treatments, it is found that one of the extracted cellulose powder from mulberry branches is more useful in the larval growth.

• Journal of Microbiology
• /
• v.45 no.6
• /
• pp.485-491
• /
• 2007

The effects of biological pretreatment on the Japanese red pine Pinus densiflora, was evaluated after exposure to three white rot fungi Ceriporia lacerata, Stereum hirsutum, and Polyporus brumalis. Change in chemical composition, structural modification, and their susceptibility to enzymatic saccharification in the degraded wood were analyzed. Of the three white rot fungi tested, S. hirsutum selectively degraded the lignin of this sortwood rather than the holocellulose component. After eight weeks of pretreatment with S. hirsutum, total weight loss was 10.7%, while lignin loss was the highest at 14.52% among the tested samples. However, holocellulose loss was lower at 7.81 % compared to those of C. lacerata and P. brumalis. Extracelluar enzymes from S. hirsutum showed higher activity of ligninase and lower activity of cellulase than those from other white rot fungi. Thus, total weight loss and changes in chemical composition of the Japanese red pine was well correlated with the enzyme activities related with lignin- and cellulose degradation in these fungi. Based on the data obtained from analysis of physical characterization of degraded wood by X-ray Diffractometry (XRD) and pore size distribution, S. hirsutum was considered as an effective potential fungus for biological pretreatment. In particular, the increase of available pore size of over 120 nm in pretreated wood powder with S. hirsutum made enzymes accessible for further enzymatic saccharification. When Japanese red pine chips treated with S. hirsutum were enzymatically saccharified using commercial enzymes (Cellulclast 1.5 L and Novozyme 188), sugar yield was greatly increased (21.01 %) compared to non-pre treated control samples, indicating that white rot fungus S. hirsutum provides an effective process in increasing sugar yield from woody biomass.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.4
• /
• pp.76-82
• /
• 2006

The dried ground needles (2.0 kg) of Chamaecyparis pisifera (Sieb. et Zucc.) Endlicher were extracted with acetone-$H_2O$ (7:3, v/v), concentrated, and fractionated with a series of n-hexane, methylene chloride, ethyl acetate and water on a separation funnel. Each fraction was freeze dried, then a portion of ethyl acetate soluble powder was chromatographed on a Sephadex LH-20 column using a series of aqueous methanol and ethanol-n-hexane mixture as eluents. The isolated compounds were identified by cellulose TLC, $^1H$-, $^{13}C$-NMR, COSY, HETCOR, FAB and EI-MS. (+)-catechin, taxifolin-3-O-${\beta}$-D-xylopyrano-side, quercetin-3-O-${\alpha}$-L-rhamnopyranoside were isolated from the ethyl acetate soluble fraction of Chamaecypairs pisifera needle. Antioxidative tests on the isolated compounds indicated that all of the compounds showed similar values to ${\alpha}$-tocopherol and BHT as controls.

• Applied Biological Chemistry
• /
• v.47 no.3
• /
• pp.325-331
• /
• 2004

In order to study the effect of formulation type on the burning characteristics of smoke generator, fenarimol smoke generators containing the powdered rice chaff as a combustible carrier were prepared by molding the kneaded mixtures into various shapes. Smoke generators containing wood flour as a combustible carrier were also prepared and compared with smoke generators containing rice chaff. All the fenarimol smoke generators moulded into powders, granules, and rods continuously burned out when the sodium chlorate content exceeded 11%. Regardless of their types, the highest smoking rate of fenarimol was observed with more than 13% of sodium chlorate. The smoking rate of active ingredient followed with the increasing order of powder (64.5%) < granule (78.4%) < rod (90.9%). The smoke rod was robust, easy to ignite, and showed the highest smoking rate among the tested formulations. When the mixture of wood flour and anti-flame agent was used as a combustible carrier, the burning rate was so slow that wood flour formulation seemed to be more suitable to a slow-burning fumigant rather than smoke generator.

• Korean Journal of Organic Agriculture
• /
• v.19 no.1
• /
• pp.121-134
• /
• 2011

For this study, Smilex powder, a pesticide, was sprayed on the Altari radish, and then underground water, Chitosan solution (${\times}$500), and wood vinegar solution (${\times}$1000) were evenly sprayed on the Altari radish respectively. Samples of Altari radishs for residual pesticide analysis were taken two hours, 1 day, 7 days, and 15 days after treatments, and the detectable concentration and degradability of procymidone, the pesticide residue, were measured. The results obtained are as follows: 1. When detectable concentration of procymidone within the altari radish was measured, treatment plots sprayed with underground water, Chitosan solution (${\times}$500), and wood vinegar solution (${\times}$1000) were found to show lower detectable concentration than the non-treatment plot which was sprayed with pesticide only. Especially, the treatment plots sprayed with Chitosan solution (${\times}$500), and with wood vinegar solution (${\times}$1,000) showed lower values than the average. 2. When the degradability of procymidone within the Altari radish was measured, the plot treated with Chitosan solution (${\times}$500) and the plot treated with wood vinegar solution (${\times}$1,000) were found to have relatively higher degradability of procymidone. There were not much differences among testing materials in the degradability of residual pesticides. However, the plot treated with Chitosan solution (${\times}$500) showed higher degradability. In terms of average degradability with time, degradability increased sharply 7 days after the foliar application of testing materials. 3. When the daily far-sighted view survey was conducted in order to find out growth disorder and damage on the Altari radish plants by the treatment of un-derground water, Chitosan solution (${\times}$500), and wood vinegar solution (${\times}$1,000), no symptomatic physiological disorders was observed on all the plants tested during the whole growing season at the tested concentration level.

• Journal of Conservation Science
• /
• v.34 no.4
• /
• pp.295-303
• /
• 2018

The application of reinforcing agents with hydraulic property and strength development characteristics was studied under conditions similar to those of mural-painting mortar made with oyster shell powder. Reinforcement mortar made with oyster shell powder showed hydraulic properties and strength to supplement the weaknesses of natural hydraulic lime(NHL); this confirmed its possibility as a wall-reinforcing material with enough strength for preserving mural paintings. Reinforcement mortar 1 showed hydraulic property and general characteristics of lime mortar, such as consistency and viscosity, as well as lower strength and higher whiteness compared to an NHL product. For Reinforcement mortar 2, the original wall sample characteristics were reflected by mixing more shell produced through calcination; and it showed similar strength to that of Reinforcement mortar 1 as well as high whiteness. In measuring the contraction ratio of reinforcement mortar samples, Reinforcement mortar 1 and 2 showed more stability in property change compared to the NHL Group.

• Advances in materials Research
• /
• v.12 no.2
• /
• pp.119-131
• /
• 2023

The development of sustainable composites materials, from recycled polymeric materials and waste from the wood industry and stone processing, allows reducing the volume of these by-products, minimizing impacts on health and the environment. Nowadays, Polypropylene (PP) is the most recycled polymer in industry, while the furniture industry has increasingly used timber felled from sustainable forest plantations as a eucalypt. The powder tailing from the ornamental stone extraction and processing industry is commonly disposed of in the environment without previous treatment. Thus, the technological option for the development of composite materials presents itself as a sustainable alternative for processing and manufacturing industries, enabling the development of new materials with special technical features. The results showed that powder granite particles may be incorporated into the polypropylene matrix associated with short eucalyptus fibres forming green hybrid composites with potential application in structural engineering, such as transport and civil construction industries.

• Textile Coloration and Finishing
• /
• v.27 no.2
• /
• pp.149-154
• /
• 2015

To investigate the biodegradation of the cellulose powder(CP) derived from Styela clava tunics(SCT), some physico-chemical properties and biodegradability of SCT-CP were measured after the incubation for 45 days. The particles size of SCT-CP prepared with washing, bleaching, drying, and grinding processes was $150-400{\mu}m$ although most of particles (70%) was more than $400{\mu}m$. The cellulose structures of SCT-CP detected using the X-ray diffraction and DSC analysis was very similar with that of wood pulp powder(WP-CP). The glass transition temperature was not detected in both samples. Furthermore, more than 90% of the SCT-CP was degraded, whereas only over 70% of the WP-CP was degraded after the incubation for 45 days. Therefore, these results suggest the possibility that SCT-CP is particularly applicable to prepare medical fiber and film for disease treatment.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.2
• /
• pp.33-40
• /
• 2013

Powdered additive or organic filler is used to improve paperboard thickness and to reduce drying energy consumption in the Korean paperboard industry. In a previous study, we identified alternative non-lignocellulosic resources to wood powder, specifically brewers grain and oil palm frond powders, and verified that these materials had the same functionality as wood powder. The main drawback of the use of such additives, including both lignocellulosic and non-lignocellulosic resources, is the deterioration in paperboard strengths. Therefore, we carried out a basic study on the surface modification of brewers grain and oil palm frond powders to improve the strengths of paperboard. Surface modification was performed using various types of cationic and oxidized starches. The streaming current and zeta-potential of the two non-lignocellulosic powders were measured and CLSM images were taken to assess the surface modification.