• Journal of the Korean Wood Science and Technology
• /
• v.40 no.2
• /
• pp.71-77
• /
• 2012

Cellulose nanowhisker (CNW) isolated from hardwood bleached kraft pulp (HW-BKP) using sulfuric acid hydrolysis was suspended in polyvinyl alcohol (PVA) and electrospun into composites nanofibers. Transmission electron microscopy (TEM) revealed the CNW to be rod-like, approximately of $16.1{\pm}4.6$ nm wide and $194{\pm}61$ nm long, providing an aspect ratio of about 12, with a particle size distribution range of $662.2{\pm}301.2$ nm. Uniform and high quality CNW/PVA composite nanofibers were successfully manufactured by the electrospinning method. As the CNW loading increases, the viscosity of CNW/PVA solutions shows a minimum at 1% CNW level which subsequently results in the smallest diameter (193 nm) of electrospun nanofibers. The average diameter of the nanofibers increased up to 284 nm with increasing CNW loading. These results suggest that the electrospinning method provides a great potential of manufacturing consistent and reliable nanofibers from CNW/PVA solution for the formation of scaffolds with potentials in future application.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.6
• /
• pp.864-871
• /
• 2016

This study was conducted to compare and analyze gross calorific values from measurement methods of lignocellulosic biomass and calculation data from calorific value prediction models based on the elemental content. The deviation of Liriodendron tulipifera (LT) and Populus euramericana (PE) was shown 7.7 cal/g and 7.4 cal/g respectively in palletization method, which are within repeatability limit 28.8 cal/g of ISO FDIS 18125. In the case of Thailand charcoal (TC), nontreatment method and palletization method was satisfied with repeatability limit as 22.8 cal/g and 8.8 cal/g respectively. Seowon charcoal (SC) was shown deviation of 11.4 cal/g in nontreatment method, because the density and chemical affinity of sample increases as the carbon content increases from heat treatment at high temperature in the case of TC and SC. In addition, after applying the elemental content of each of these samples to the calorific value prediction models, the study found that Model Equation (3) was relatively consistent with measured calorific values of all these lignocellulosic biomass. Thus, study about the correlation between the density and size of particle should be conducted in order to select the measurement method for a wide range of solid biofuels in the future.

• Journal of Environmental Science International
• /
• v.19 no.3
• /
• pp.379-387
• /
• 2010

Sediments of Little Scioto (LS) River in Ohio was contaminated by poor disposal of creosote from Baker Wood Creosoting Facility. Among the primary compounds of creosote, Polycyclic Aromatic Hydrocarbons (PAHs) are the most common ingredient PAHs are known for toxic, carcinogenic and mutagenic compounds. There are many difficulties to remove the PAHs in nature environment because their characteristics are having a less water-solubility, volatile and low mobility properties as increasing the molecular weight. The generation of hydroxyl radicals (${\cdot}OH$) and hydrogen peroxide ($H_2O_2$) forms as well as high temperature (5000 K) and pressure (1000 atm) by a physico-chemical effects of ultrasound during a cavitation collapse can promote the degradation and desorption of PAHs in sediment And it can also produces shock wave and microjets which are able to change the size and surface of particle in solid-liquid system as one of physical effects. Therefore, we explored to understand the role of particle size, the effect of elimination for PAHs concentration by ultrasound and optimize the conditions for ultrasonic treatment. The condition of various size of particles (> $150{\mu}m$, < $150{\mu}m$) and solid-liquid ratio (12.5g/L, 25g/L) for the treatment was considered and ultrasonic power (430 W/L) with liquid - hexane extraction and microwave extraction method were applied after ultrasound treatment.

• Journal of the Korean Wood Science and Technology
• /
• v.46 no.2
• /
• pp.155-165
• /
• 2018

The objective of the research was to evaluate the effect of particle pre-treatment on physical, mechanical, and durability of jatropha fruit hulls (JFH) particleboard. The pre-treatments included were immersing in cold water, hot water, and acetic acid solution. After each treatment, the particles were dried up to 3% moisture content. Urea-formaldehyde (UF) resin was used to fabricate particleboards with board size, thickness and density target of 25 cm by 25 cm, 0.80 cm, and $0.70g/cm^3$, respectively. Board pressed at $130^{\circ}C$ for 10 minutes, and $25kg/cm^2$ pressure. The evaluation of particleboard followed the JIS A 5908-2003. Whilist their resistance to subterranean termite test (mass loss, mortality, antifeedant value and feeding rate) refers to the Indonesian standard (SNI 01.7207-2006). The physical and mechanical properties of particleboards showed that all pre-treatments decreased the pH of particles. Overall, all particle immersing treatments resulted of better physical and mechanical properties of particleboard than those of untreated ones. The acetic acid treatment resulted the best physical and mechanical properties of particleboard. Based on the mass loss of JFH particleboard, hot water and acetic acid treated particleboards were classified into weak resistance to subterranean attack. The other two treatments were classified into very weak resistance. Hot water treated particleboard provided the highest mortality and antifeedant as much as 87.40% and 34.20%, respectively. Based on antifeedant classification, hot water treated particleboards were classified into moderately strong resistance, while other treatments were categorized into weak resistance. The lowest feeding rate value ($45.30{\mu}g/termite/day$) was attained by hot water treatment.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.6
• /
• pp.821-827
• /
• 2016

This study evaluates the economic feasibility of industrializing fluidized bed dryer for wood particles. The theoretically required heat energy and energy efficiency were evaluated using a pilot scale fluidized bed dryer. When Mongolian Oak wood particles with 50% initial moisture content were dried in the fluidized bed dryer with air of $70^{\circ}C$ air circulating at 1.1-1.3 m/s for 30 minutes, the total theoretically required heat energy was 2,177 kJ. Of this, 1,763 kJ (approximately 81.0%) was used to heat the air flowing in from outside the dryer and 386 kJ (approximately 17.7%) was used to heat and remove water from the wood particles. Actual energy consumed was 7,560 kJ, giving energy efficiency of 28.8%. Thus, to industrialize a drying method such as fluidized bed drying, where the dryer volume is significantly larger than the volume of wood particles, it is necessary to minimize energy loss and maximize energy efficiency by designing the dryer size considering the amount of wood particles and choosing a suitable air circulation rate.

• Journal of the Korean Wood Science and Technology
• /
• v.48 no.6
• /
• pp.861-868
• /
• 2020

The use of polyphenol extracts from radiata pine (Pinus radiata) bark as raw materials for bio-foams was investigated along with the optimal NaOH extraction conditions. The targeted yield of alkaline extracts was 60%, and the targeted pH was 11 to 12. The radiata pine bark was composed of 70% of a 1% NaOH extract, which contained mainly polyphenols, such as proanthocyanidin (PA). As the particle size of the bark decreased, the yield of the 1% NaOH extracts increased from 57 to 87%. A range of NaOH concentrations, liquor ratios, and extraction times were explored to establish an economic polyphenol extraction method. More than 60% of the alkaline extract was extracted, and the pH of the extract was approximately 12 when the optimum extraction conditions were employed, i.e., a liquor to bark ratio of 5:1, a NaOH dosage of 17 to 18% based on the bark weight, and a 1 h extraction time. Following neutralization of the alkaline extract, structural analysis indicated severe structural changes in the PA during the alkaline extraction. Because the alkaline extract was barely soluble in the solvent used for the structural analyses, it is assumed that chemical modification is required to increase the solubility of the alkaline extract for the production of bio-foams.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.3
• /
• pp.71-78
• /
• 2004

The purpose of this study was to investigate the water absorption and thickness swelling of biocomposites at room temperature. These properties of bio-composites mainly depend on the ability of the agro-flour to absorb water through hydrogen bonding between water and the hydroxyl groups of the holocellulose and lignin in the cell wall. As the content of agro-flour increased, the water absorption and thickness swelling of the bio-composites increased. The effects of agro-flour content and rice husk flour (RHF) particle size on the water absorption and thickness swelling of the bio-composites were evaluated. In general, wood-based materials showed significantly higher water absorption and thickness swelling than the bio-composites. This might be attributed to the ability of the polybutylene succinate (PBS) hydrophobic polymer to prohibit the water absorption and thickness swelling of the bio-composites, Therefore, the use of agro-flour filled PBS bio-composites, which exhibit improved dimensional stability in comparison with wood-based materials, is recommended.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.6 no.1
• /
• pp.67-76
• /
• 1996

This study was performed to estimate total dust concentrations and particle size distribution of wood dust in the furniture and sawmill industries. To compare total wood dust concentrations, two samplers recommended by the American Conference of Governmental Industrial Hygienists and by the National Institute for Occupational Safety and Health were used. Concentration data were analyzed by paired-t tests using the SAS program and two parameters of the particle size distributions were determined by histogram. The results were as follows: 1. Particle size distributions showed a unimodal pattern in cutting and a bimodal in sanding operations. Mass median aerodynamic diameters(MMAD) were $17.35{\mu}m$ in cutting, and $1.39{\mu}m$ for small mode and $18.89{\mu}m$ for large mode in sanding operations. The proportions of particle size larger than $9.8{\mu}m$ estimated by the impactor were 61.16 % in cutting and 62.33 % in sanding operations, respectively. 2. The average personal total dust concentrations measured by IPM sampler were $17.12mg/m^3$ (GSD=1.45) from indoor samples, $2.97mg/m^3$(GSD=1.90) from outdoor samples in cutting, and $8.01mg/m^3$(GSD=1.58) from sanding operation. And those of by 37 mm closed-face cassette were $9.12mg/m^3$(GSD=1.46), $1.06mg/m^3$(GSD=1.99) from cutting, and $3.32mg/m^3$(GSD=2.16) from sanding operations. 3. The average area total dust concentrations measured by IPM sampler were $1.88mg/m^3$(GSD=2.04) from indoor cutting, $4.76mg/m^3$(GSD=2.83) from indoor sanding operations. And those of by 37mm closed-face cassette were $0.49mg/m^3$(GSD=2.34) from cutting, and $1.32mg/m^3$(GSD=3.03) from sanding operations. 4. The ratio of personal total dust concentrations measured by 37 mm closed-face cassette to those by IPM sampler were 35.7 %, 53.3 % from cutting, and 41.4 % from sanding operations. 5. The ratio of area total dust concentrations measured by 37 mm closed-face cassette to those by IPM sampler were 26.1 % from cutting, and 27.7 % from sanding operations. 6. A statistically significant difference of total dust concentrations between the 37 mm closed-face cassette and the IPM sampler was found.

• Corrosion Science and Technology
• /
• v.22 no.3
• /
• pp.187-192
• /
• 2023

The use of biomass is increasing as a response to the convention on climate change. In Korea, a method applied to replace fossil fuels is using wood chips in a cogeneration plant. To remove air pollutants generated by burning wood chips, a selective denitrification facility (Selective catalytic reduction, SCR) is installed downstream. However, problems such as ash deposition and descaling of the equipment surface have been reported. The cause is thought to be unreacted ammonia slip caused by ammonia ions injected into the reducing agent and metal corrosion caused by an acidic environment. Element analysis confirmed that ash contained alkali metals and sulfur that could cause catalyst poisoning, leading to an increase in the size of ash particle and deposition. Measurement of the size of ash deposited inside the facility confirmed that the size of ash deposited on the catalyst was approximately three times larger than the size of generally formed ash. Therefore, it was concluded that a reduction in pore area of the catalyst by ash deposition on the surface of the catalyst could lead to a problem of increasing differential pressure in a denitrification facility.

• Korean Journal of Environmental Agriculture
• /
• v.28 no.4
• /
• pp.340-346
• /
• 2009

Chromated copper arsenate (CCA) is a chemical wood preservative that has been intensively used to protect wood from decay during the last few decades. CCA is widely used to build structures such as decks, fences, playgrounds and boardwalks. However, structures constructed of CCA-treated wood have caused adverse environmental effects due to leaching of Cr, Cu and As into surrounding soils. This research was conducted to monitor the vertical and horizontal distribution of Cr, Cu and As in soils adjacent to CCA-treated wood structures in Korea. Two structures constructed with CCA-treated wood were selected at Hongcheon and Chuncheon in Gangwon Province, South Korea. Eleven soil profile samples were collected at depths of 0 to 80 cm at each site, while 12 surface soil samples were collected at distances of 0 to 200 cm from each structure. The soil chemical properties, soil particle size distribution and total metal concentrations were then determined. The results revealed that soils near CCA-treated wood structures were generally contaminated with Cr, Cu and As when compared to the background concentration of each metal. In addition, the concentrations of Cr, Cu and As in soils decreased as the vertical and horizontal distance from the structure increased. Further studies should be conducted to evaluate the mobility and distribution of these metals in the environment as well as to develop novel technologies for remediation of CCA contaminated soils.