• Journal of the Korean Wood Science and Technology
• /
• v.47 no.2
• /
• pp.129-144
• /
• 2019

This study aimed at developing an accelerated collection method that reduces measurement and collection time by improving and complementing the desiccator method, which is mainly used for quality control in wood-based panels and furniture production sites. First, this study measured the formaldehyde emissions from the wood-based panels by grade using the desiccator method. Further, this study compared the desiccator method with the developed process and analyzed the correlation in optimal temperature, time, and exposed area. The results showed that the developed process resulted in relatively similar outcomes in comparison to the desiccator method when the temperature was $100^{\circ}C$, the time was 1 h, and two specimens were used, at which the correlation was high. To verify the developed process, this study commissioned Korea Conformity Laboratories with the standardized temperature, time, and the number of specimens to compare them with the specimen that was not used in the actual test. As a result, the correlation to the desiccator method was shown to be very high. However, the formaldehyde emission measured by the accelerated collection process was mostly higher than that measured by the desiccator method. The formaldehyde emission grades from several specimens were one level higher. However, from the perspectives of quality control, it was determined that the accelerated collection method developed in this study could be sufficiently used.

• Journal of Forest and Environmental Science
• /
• v.39 no.1
• /
• pp.55-64
• /
• 2023

Properties of a lesser-used wood species were investigated to determine its potential for structural utilization. Trees of Delonix regia were felled and sampled at the base, middle and top and then sectioned to inner wood, middle wood, and outer wood for variation across the axial and radial directions. Hence, selected physical and mechanical properties as well as natural durability of D. regia along the radial and axial directions were examined. Obtained data were analyzed using analysis of variance (ANOVA) at α_0.05. There was no significant difference in the Moisture content (MC) of the wood but specific gravity (SG) decreased from base to top ranging from 0.35-0.44. Water absorption, volumetric swelling, and volumetric shrinkage range from 46.18-51.86%, 2.57-4.02%, and 2.26-3.96% respectively along the axial plane. The weight loss for graveyard exposure and accelerated laboratory decay test ranged from 25.14-48.00% and 32.02-44.45% respectively. Modulus of Rupture and Modulus of Elasticity values range from 29.42-72.68 Nmm² and 3,834.54-8,830.37 Nmm² respectively. The SG values has confirmed the species as a medium density wood and values of other properties tested showed that the wood is dimensional stable and moderately resistance to fungi and termite. Hence, it could be used for light construction purposes such as furniture and other interior woodwork.

• Journal of the Korea Furniture Society
• /
• v.10 no.1
• /
• pp.65-71
• /
• 1999

The bending performance of sloped finger-jointed Rhus verniciflua were tested in order to improve the strength properties of finger-joint. Sloped finger-cut pieces were jointed with three kinds of adhesives (polyvinyl acetate, polyvinyl-acryl acetate and oilic resin). The slope ratios of finger joints were 0, 1.0, 1.5, and 2.0. The MOE, MOR and deflection to maximum load in bending of sloped finger-joints and solid wood specimen were measured. The results were : 1) The efficiencies of MOE to finger and sloped finger-joints to the solid wood were almost same in the three kinds of adhesives(polyvinyl acetate, polyvinyl-acryl acetate and oilic urethane resin) and there were some effect of slope on the MOE in a sloped finger-joint for three kinds of resin adhesives. 2) There was the effect of slope on the MOR in sloped finger-joints in every kind of adhesive. The efficiencies of MOR in slope ratios of 0 and 2.0 ranged 65-79%, respectively. There was also a slight effect of the kinds of adhesives on the MOR. However, the efficiencies of deflection to the urethane resin adhesive were much less than those of polyvinyl acetate, polyvinyl-acryl acetate resin adhesives except the slope ratio of 0. 3) It might be impossible to estimate the bending stregth of sloped finger-jointed Rhus verniciflua by using MOE. The correlation coefficient(0.192) between MOE was very low and not significant at 5% level.

• Journal of the Korea Furniture Society
• /
• v.20 no.4
• /
• pp.281-289
• /
• 2009

This research examined the technical feasibility of composite that had two layers of fiberglass reinforcement to enhance the load carrying capacity of lumber. Specimens were prepared from standard lumber made of thinning crop trees such as Larix kaempferi, Pinus koraiensis, and P. rigida. Results indicated that bending properties, hardness, and wood screw withdrawal load of low density lumber from the P. koraiensis increased as the number of layers of fiberglass reinforcement increased. Composite produced by VARTM method showed the MOE increased in all specimens, while the MOR differed on the location, whether the 2-layers of FRP is put on tensile zone or compressive zone. The MOR of high density lumber from Larix kaempferi and P. rigida decreased when they placed into tensile zone, but low density lumber from P. koraiensis increased in same location. The bending toughness only increased high density lumber of Larix kaempferi as the number of layers of fiberglass reinforcement increased. The technique developed by this study may increase an opportunity to use small diameter log with low density for commercial purposes.

• Journal of the Korea Furniture Society
• /
• v.21 no.1
• /
• pp.62-71
• /
• 2010

This study was carried out to investigate the physical and mechanical properties of 6 hardwoods before and after heat treatment in an effort to produce the high quality industrial lumber product. The object of the research was to design living products with heat treated woods. The results were as follows. Specific gravities of green woods were in range from 0.87 to 1.12. The specific gravities of never treated woods showed higher than those of the heat treated woods. The shrinkage of heat treated woods when green to air & oven dry was significantly low, compared to never treated woods. The compression strengths parallel to grain of heat treated woods showed higher than those of never treated woods. The moduli of rupture (MOR) of never treated and heat treated woods were $170.37N/mm^2~107.07N/mm^2$ and $122.78N/mm^2~61.27N/mm^2$ respectively. MORs of heat treated woods showed lower than those of never treated woods. The modulus of elasticity (MOE) of heat treated woods showed higher than those of never treated woods.

• Journal of the Korea Furniture Society
• /
• v.25 no.4
• /
• pp.319-324
• /
• 2014

Red pine is a popular species for making a cutting board in Korea, but easily sap stained. Heat treatment could improve its quality by darkening and equalizing the color of sap stained wood. The color change of sap stained red pine boards was investigated by heat treatment at $190^{\circ}C$. It was observed that the color of heat treated boards got darker and it made the color of sap stain vanished. A colorimeter was used to measure color indexes. It was revealed that the values of the lightness ($L^*$) and the yellowness ($b^*$) decreased as heat treatment repeated while the values of the redness ($a^*$) increased. The average of the color difference (${\Delta}E^*$) between the control and 1st heat treated boards was 16.1, which could be expressed as 'Extremely different' while that between the 1st and 2nd heat treated boards was 8.3, which could be expressed as 'Considerably different'. The fact that heat treatment equalized the color of boards was confirmed by a statistical analysis.

• Journal of the Korea Furniture Society
• /
• v.10 no.2
• /
• pp.1-8
• /
• 1999

The use of structural wood based panels like plywood, OSB in many applications involves the use of nails, and data on the performance of panel-nail connection are needed for design and comparative purpose. This study was carried out to develop basic information on nail performance(withdrawal, embedding, nailhead push through) with water absorption in plywood and OSB. In withdrawal resistance test, initial stiffness of plywood performed better than OSB in 24hr soaked condition. The soaked condition reduced average nail withdrawal resistance value about 46% (12d mail), 53%(8d nail) in OSB, 17%(12d mail), 24%(8d mail) in plywood. The nail embedding strength of plywood also performed better than that of OSB and retention value(wet strength/dry strength) yielded similar in each nail types. The nail head push through capacity of OSB was higher than that of plywood in dry condition, but equal or lower in soaked condition. Therefore, critical consideration about structural panels is required in moist applications. The average values of nail withdrawal, nail embedding strength and nail head push through resistance of tested materials meet the minimum requirement of various specification and standards.

• Journal of the Korea Furniture Society
• /
• v.24 no.4
• /
• pp.444-451
• /
• 2013

In this paper, experimental results were presented on the moment resistance of a concealed timber post base joint aimed at replacing in a modern design introduced lately the wood to wood joints used in the traditional Korean timber house - Hanok. Preliminary results showed that the original configuration of the joint offers a limited moment resistance and a low ductility and energy dissipation. In an attempt to mitigate those limitations without undergoing major changes in the connector, three new configurations were proposed and investigated. Motivated by the wish to prevent the early failure in welds, a first approach consists in directly bolting the connector's upper plate to lower the stress on the weak welds. Alternatively, another approach focused on increasing the strength of these welds by extending their length to the full width of the metal wings. Finally, a third configuration investigated the effect of those two approaches combined. In conclusion, reinforcing the welds found out to be the best option among the presented ones. As a result, this connector considered to show proper ability for use in earthquake-resistant structures with suited lateral-resistant structural elements.

• Journal of the Korea Furniture Society
• /
• v.12 no.2
• /
• pp.1-10
• /
• 2001

As finger joint method has a high rate of yield and high strength and ease in working, it has been widely used as an end joint method for solid wood and wood based-material. Therefore, we end-joined the material of Pinus densiflora, Quercus variabilis and populus euramericana with polyvinyl acetate adhesive and resorcinol phenol resin adhesive. The effect of difference (0, 0.15, 0.3, 0.45mm) between the dimensions of tip width and root width of the finger (DTRW) on bending strength properties was as follows: 1. In the case of polyvinyl acetate adhesive, DTRW had no effect on bending modulus of elasticity(MOE) and modulus of rupture(MOR) of the three kinds of species, because their bonding layers were destroyed by slippage, not their woody parts. 2. In the case of resorcinol phenol resin adhesive, the material of Quercus variabilis showed an optimal result at 0.15 or 0.3 of DTRW, while the poplar did at 0 of DTRW 3. The differences in efficiency ratio of bending MOR of populus euramericana, Pinus densiflora and Quercus variabilis species according to the kind of adhesive were 13-29%, 23-30% and 45-53%, respectively.

• Journal of the Korea Furniture Society
• /
• v.11 no.1
• /
• pp.45-51
• /
• 2000

It was thought that the stiffness of a coated specimen became lower than that of the solid wood because the stiffness of the dried film of coating material is lower than that of the solid wood. The authors were trying to compare the effect of lacquer varnish and rhus lacquer on the resonant frequency of the solid woods for the violin, spruce and maple. Vibration modal shape of coated specimens were same to those of solid woods, but the frequency became lower at each mode as were expected regardless of coat. frequency decrement of coated specimen was getting larger at upper mode in both European violin woods, however, rhus lacquer coated spruce specimens were less affected than lacquer varnish coated specimens.