• Journal of the Korean Wood Science and Technology
• /
• v.46 no.1
• /
• pp.10-16
• /
• 2018

Lindera erythrocarpa is a less utilized species in Korea although that it has straight stem and it grows up to 40 cm in diameter. A proper kiln-dry schedule is required in advance to utilize an unknown species. Terazwa's quick oven-dry method was used to find it and which was confirmed by drying 25 mm thick boards in a kiln. The average green moisture content and the average green specific gravity of Lindera erythrocarpa are 72.3% and 0.53, respectively. Prospective kiln-drying conditions obtained by Terazwa's quick oven-dry method are a initial dry-bulb temperature of $50^{\circ}C$, a initial wet-bulb depression of $4^{\circ}C$ and a final dry-bulb temperature of $75^{\circ}C$, which are in a good agreement with USDA FPL kiln-dry schedule of T5-D4. 25 mm thick boards dried in a kiln with T5-D4 kiln-dry schedule did not have any severe drying defects such as honycombing and warping. A severer kiln-dry schedule of T8-C5 was developed and applied to another kiln-drying run to confirm it.

• Journal of the Korean Wood Science and Technology
• /
• v.17 no.3
• /
• pp.67-81
• /
• 1989

This experiment was carried out to know the mothod of changing the step of moisture content schedule with time in conventional kiln drying. For the purpose of this object. we made drying model by applying the moisture diffusion model by J.FSiau(1984) to average moisture content equation by J.Crank(1956) derived it from Fick's second law. And to verify this method of drying model. 2.5cm-thick boards and 5.0cm-thick dimension lumbers of Pinus densiflora were kiln-dried with the schedule of T11-C3 and T10-C4, respectively. And then the drying rates were investigated and compared with those calculated from drying model. The results obtained were as follows 1. Average drying rate and total drying time of board to dry to 6.5% moisture content were 0.64%/hr and 109hr., and those of dimension lumber to dry to 8.3% moisture content were 0.4%/hr. and 162hr., respectively. 2. The moisture content of shell and core decreased by equalizing treatment and increased by conditioning treatment both on board and dimension lumber. But the moisture gradient was lower after conditioning than after equalizing. 3. As the drying was proceeded, the transverse bound water diffusion coefficient all but linearly decreased, the water vapor diffusion coefficient abruptly curvilinearly increased, while the transverse diffusion coefficient curvilinearly decreased both on board and dimension lumber. But each of diffusion coefficients on board was larger than that on dimension lumber. 4. Compared to experimential drying rate of board. theoretical drying rate was larger at 30.0%-21.8% moisture content range and was similiar at 21.8%-5.4% moisture content. And in case of dimension lumber, the drying rate was similiar at 30.0%-16.1% moisture content range but theoretical drying rate was much lower at 16.1%-8.3% moisture content range. 5. The possibility of adapting this drying model to changing the moisture content schedule step with time was in the range of 21.8%-5.4% moisture content on board. And in the case of dimension lumber that was in the range of 30.0%-16.1% moisture content.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.5
• /
• pp.622-628
• /
• 2017

In order to develop value-added utilization technology of domestic oaks the processing yield rate from the standing tree to the flooring material for the Quercus variabilis and Quercus mongolica were investigated. Also, to reduce drying time, improved drying schedule was applied and the physical properties were measured. The drying time was 173 hours in total, and the final moisture content was 5.39% (Quercus variabilis) and 4.17% (Quercus mongolica). The color difference of oak lumber before and after drying showed a significant change as ${\Delta}E$ value from 7 to 11. The shrinkage rates of Quercus variabilis and Quercus mongolica during drying were 8.1% and 8.5% in the tangential direction and 5.0% and 6.2% in the radial direction, respectively. The lumber manufacturing yield rate of sawn lumber was 30 to 40% and that of the final product was 8 to 15%. It is expected that the processing characteristics of the Quercus species investigated in this research could contribute to formulate an efficient production plan of domestic hardwoods that are still under utilization.

• Journal of Conservation Science
• /
• v.37 no.5
• /
• pp.579-589
• /
• 2021

Five waterlogged wood artefacts were excavated from Suyeong-ri site in Hwaseong, South Korea. The aim of the present study was to identify the species and estimate the date of manufacture and the manufacturing method of these artefacts. The study also aimed to conserve the original shapes of waterlogged wood artefacts by using the vacuum freeze drying method. The two large waterlogged woods were identified as Ulmus spp. and Morus spp., whereas one of the three small waterlogged woods was identified as Abies spp. and the other two as hard pine. Radiocarbon dating using wiggle match dated the manufacturing of these wooden artefacts between BCE 8520-8490 or BCE 8470-8290 in the Neolithic age, and a similar period was also confirmed for seed excavated from a place close to the location where the waterlogged wood artefacts were excavated. The surface of waterlogged wood artefacts had several traces of manufacturing processes - traces of tearing and chopping - were observed. Based on these observations, it was confirmed that stone adz was used to make these wooden artefacts. Thereafter, the waterlogged wood samples were conserved by immersing them into PEG#4,000 of concentration in water from 10% to 40% at room temperature(15~25℃) and subjecting them to vacuum freeze drying. However, the internal moisture was not completely removed in some thick parts of waterlogged woods by applying the general schedule such as raising the shelf temperature as the surface temperature rises. Therefore, additional study is required using the schedule-method for vacuum freeze drying of large waterlogged wood.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.1
• /
• pp.45-54
• /
• 1986

A study was conducted to determine the physical properties related to drying characteristics, the seasonal air drying curves and the kiln drying schedule for taun lumber imported and utilized. This kiln drying schedule was found by oven drying and developed by pilot testing of green lumber and partially air dried lumber. The results of this study were as follows; 1. Average green specific gravity and standard deviation of heartwood lumber were 0.60${\pm}$0.03 and those of sapwood lumber were 0.64${\pm}$0.02. 2. Radial shrinkage from green to air dry and from green to oven dry were 3.05 percent and 5.96 percent respectively, and tangential shrinkage from green to air dry and to oven dry were 5.49 percent and 8.74 percent respectively. 3. Drying time for 25mm thick green lumber (50 percent moisture content) air dried to 30 percent moisture content were 14 days in springtime. 6 days in summertime, and 12 days in autumntime, whereas for 50mm thick lumber in 36 days in springtime, 18 days in summertime, 38 days in autumntime. 4. Kiln drying schedules developed by oven drying were T8-B3 for 25mm thick lumber and T5-B2 for 50mm thick lumber. 5. Kiln drying curves of green 25mm and 50mm thick lumber were similar to those of partially air dried lumber from the level of 30 percent average moisture content. Green 25mm thick lumber (55.7 percent moisture content) was dried to 9.3 percent moisture content in 101.5 hours and green 50mm thick lumber (65.6 percent moisture content) was dried to 11.5 percent moisture content in 526 hours. 6. End checking for green 25mm thick lumber occured in 49.6 percent moisture content and reached maximum amount in 27.6 percent moisture content and closed in 15.8 percent moisture content. 7. End checking for green 50mm thick lumber and partially air dried lumber developed and reached maximum amount earlier then for 25mm thick lumber. 8. Final moisture content of surface layer for 50mm thick lumber was one half of that of core, and moisture content equalized in the lumber after nine days of room conditioning. 9. Casehardening for 50mm thick lumber was slight and was conditioned after nine days of room stroage. 10. Drying defects, such as end checking and surface checking, were not observed and the quality of dry lumber was first.

• Journal of the Korean Wood Science and Technology
• /
• v.20 no.2
• /
• pp.51-60
• /
• 1992

This study was performed to investigate the effect of green sorting before drying on the high-temperature drying characteristics of southern yellow pine dimension lumber(2"${\times}$6"${\times}$12'). To test the advantages of weight sorting, green lumber was seperated into heavy(above 55 1b), medium(50-55 1b), and light(below 50 1b)weight classes. Pieces in each weight class were subgrouped into high(above 35%) and low(below 30%) latewood groups. Groups were dried and seperated by a standard commercial high-temperature schedule; dry bulb temperature $245^{\circ}$ F, wet bulb temperature $180^{\circ}$ F, and air velocity 1200fpm. The results obtained were as follows; 1. There was a highly significant correlation between annual rings per inch(X) and percent-latewood(Y). The regression equation was Y=24, 5047+1.3272X. 2. There were highly significant correlations between either annual rings per inch($X_1$) or percent-latewood($X_2$) a.d specific gravity in green wood(Y). Their regression equations were Y=0.4260+0.0081$X_1$ and Y=0.3749+0.0029$X_2$, respectively. 3. Heavier weight charges dried more slowly than lighter weight charges. 4. Board-to-board variation in green or dry moisture content was less for all seperate weight classes than for unseperated control charges. 5. Lower latewood pieces had higher initial moisture content than higher latewood pieces, and then drying time for lower late wood pieces was longer than higher latewood pieces.

• Journal of the Korean Wood Science and Technology
• /
• v.29 no.1
• /
• pp.1-8
• /
• 2001

Red pine (Pinus densiflora), white pine (Pinus koraiensis), larch (Larix leptolepis) and Western hemlock (Tsuga heterophylla) lumber were vacuum-press dried under three drying schedules to investigate current moisture contents (MC), drying rates and drying time factors related to five lumber thicknesses of 3, 5, 7, 9 and 11cm. Current MC could be estimated by drying factors such as lumber thickness, initial Me and drying time. Average drying rate from 30% to 15% Me was the highest for Western hemlock below fiber satuartion point, red pine, white pine and larch in the order of their magnitude. Drying rate curvilinearly decreased as lumber thickness increased. Drying time factor curvilinearly increased as lumber thickness increased.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.3
• /
• pp.192-199
• /
• 2009

This study was carried out to investigate the performance of a radio-frequency/vacuum dryer combined with a mechanical compressive load (RF/VC) with a scale of about $3m^3$ during drying board of Azobe (Lophira alata) and Korean red pine (Pinus densiflora). The degree of vacuum of the RF/VC system was maintained at 80~105 torr, and wood temperature was increased from $40^{\circ}C$ at the beginning of drying to $60^{\circ}C$ at the end of drying and the radiofrequency generator was operated with schedule of 7 minute-ON and 3 minute-OFF. The wood temperatures near charge plate always remained higher than those of the control during all of the drying stage, whereas the wood temperature near ground plate always remained lower than those of the controlled. As drying time proceeding, the temperature of the wood near ground plate presented lower than those of the control. Whereas the temperature of the wood near charge plate presented higher than those of the controlled. The final average moisture contents of the Azobe boards stacked near the input side of the RF generator showed slightly lower than those near the opposite side. Those of the wood stacked in the layers near the charge plate were lower than those of near the ground plate. The average length of surface checks of the Azobe boards stacked near the charge plate was very slight, whereas that toward the ground plate represented high values. The efficiency of input energy was simliar with the commercial systems.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.1
• /
• pp.52-58
• /
• 2004

Oak is one of major species in this country as well as pine, but has been less utilized because of its refractory properties. The purpose of this study is to develope an effective method for drying the boards and disks of Quercus variabilis. Among four end-coaters used in this study thick coating with polyvinyl acetate chrolide glue (PVAc) was proved as the most effective. The average air-drying rate of boards was 1.2%MC/day, which did not exceed the safe drying rate recommended by United States Department of Agriculture (USDA). The kiln drying schedule used in this study gave a good result in drying the air-dried boards to 8%MC without any internal checks. An attempt to prevent oak disks from V-cracking during air-drying using special pallet-type stickers was not successful.

• Journal of the Korean Wood Science and Technology
• /
• v.32 no.4
• /
• pp.46-51
• /
• 2004

The objective of this study was to evaluate the applicability of high temperature drying to pitch pine (Pinus rigida) lumber, especially intended for use as lamina of structural glued laminated timber (glulam), to enhance the efficient utilization and provide added-value to that species. The high temperature schedule and drying procedures utilized were shown to be reasonable for drying glulam lamina due to the occurrence of small moisture gradients, minimal residual drying stress, and low warpage. Through preliminary tests, it was confirmed that residual resin at lamina surfaces did not adversely affect the gluing process. However, quantitative analysis of resin is required for developing a method to constrain the occurrence of pitch trouble with respect to decreasing long-term adhesive and finish durability of glulam in use after manufacturing. The final moisture content of high temperature dried lamina was much lower than target moisture content and discoloration was more severe than anticipated. In a further study, it will be necessary to determine the optimal drying conditions, such as temperature, humidity, drying time, and top load restraint level, which could best control discoloration, warpage, and moisture content of the lamina, while minimizing fuel expense.