• Journal of Korean Society of Forest Science
• /
• v.95 no.4
• /
• pp.429-434
• /
• 2006

The dried needles (1.5 kg) of Picea abies Karsten were ground, extracted with acetone-$H_2O$ (7:3, v/v), concentrated, and fractionated with a series of n-hexane, methylene chloride, ethyl acetate and water on a separatory funnel. Each fraction was freeze dried, then a portion of ethyl acetate soluble powder was chromatographed on a Sephadex LH-20 column using a series of aqueous methanol and ethanol-n-hexane mixture as eluents. The isolated compounds were identified by cellulose TLC, $^1H$-, $^{13}C$-NMR, FAB and EI-MS. (+)-catechin (compound I), (-)-epicatechin (compound II), kaempferol-3-O-${\beta}$-D-glucopyranoside (compound III), 4-hydroxyacetophenone (compound IV) were isolated from the ethyl acetate soluble fraction and (+)-catechin (compound I), protocatechuic acid (compound V) were isolated from the $H_2O$ soluble fraction of P. abies needle. The antioxidative activities of each fraction and the isolated compounds were tested by DPPH radical scavenging method, and EtOAc soluble fraction, (+)-catechin and (-)-epicatechin showed similar values to ${\alpha}$-tocopherol and BHT as controls.

• Journal of the Korean Wood Science and Technology
• /
• v.36 no.4
• /
• pp.26-36
• /
• 2008

As the height of the light-framed building increases, the lateral load and overturn-moment are increased and the possibility of the building overturn becomes larger. Because the shear wall resists lateral load in light-framed building, the reinforcement of shear wall is required. In order to reinforce the light-framed shear wall, using lag screw fastener type (B-HD) and using bolt type (S-HD) hold-down connectors were applied for test. And domestic larch lumbers, $38{\times}140mm$ and $89{\times}140mm$, KS 2nd grade, were used for the stud. The North American OSB panels were used for sheathing panel. Static loads, load speed 6 mm/min, were applied on top of the wall. As a result, shear strength of the wall that using hold-down connector was improved sufficiently. And when applying the S-HD type hold-down connector, stud should be reinforced against weakening by drilled hole. As increasing the number of lag screw, the number of bolt and the product allowable strength, the strength of shear wall that using hold-down connector was also increased. When applying hold-down connector to light-framed building using 38 mm stud, it must be reinforced by enlarging the thickness of stud like as 38 mm doubled column.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.1
• /
• pp.63-71
• /
• 2002

The bark of P. alba × glandulosa, P. euramericana and P. nigra × maximounczii F₁, several Populus trees, were collected, extracted with acetone-H₂O(7:3, v/v), fractionated with hexane, chloroform and ethylacetate, and freeze dried to give some dark brown powder. Each fraction of the powder was chromatographed on a Sephadex LH-20 column using a series of aqueous methanol and ethanol-hexane mixture as eluents and then identified by thin layer chromatography using TBA and 6% acetic acid as developing solvents. The structures of the isolated compounds were characterized by ¹H, ¹³C and 2D-NMR tools including mass spectrometry. Most of the compounds were flavonoids and salicin derivatives as follows: (+)-catechin, taxifolin, aromadendrin, eriodictyol, naringenin, sakuranetin, sakuranetin-5-O-𝛽-D-glucopyranoside, neosaturanin, salireposide, p-coumaric acid, and aesculin from P. alba × glandulosa, (+)-catechin, salireposide, populoside and salicortin from P. euramericana and (+)-catechin, quercetin, padmatin, salireposide, populoside and salicortin from P. nigra × maximounczii F₁.

• KSBB Journal
• /
• v.16 no.6
• /
• pp.603-608
• /
• 2001

In this study, we studied on the remeval of toluene vapors in a lab-scale biofilter. Biofiltration was performed in a column fed downflow with contaminated air at ambient conditions. The column was packed with mixture of Peat and Calstene(5:3 vol. Ratio), Synthesized media, Bark and Wood chip, which were inoculated with microbial population of selected stains(Pseudomonas. putida, KCCM 11343, ATCC 12633). The microorganisms were immobilized on the bed medium and then biofilm were formed. The biofilter was operated under the conditions of various inlet toluene concentrations for 180 days and treated up to the elimination capacity of maximum 40 g/㎥hr at the inlet load of 30 g/㎥ hr with percentage removals of 20∼90% and gas retention times between 1 and 2 min. The pressure drop was very negligible through the biofilter columps because its value of 0.054 cmH$_2$O/m was much less than others. The effect of operating conditions such as flow rate, inlet toluene concentration and moisture contents on the performance of the biofilter was sequentially investigated in this study.

• Journal of Microbiology and Biotechnology
• /
• v.22 no.11
• /
• pp.1540-1548
• /
• 2012

Manganese peroxidase (MnP) was isolated from the culture filtrate of the wood log mushroom Stereum ostrea (S. ostrea), grown on Koroljova medium, and then purified by ammonium sulfate [70% (w/v)] fractionation, DEAE-cellulose anion exchange chromatography, and Sephadex G-100 column chromatography, with an attainment of 88.6-fold purification and the recovery of 22.8% of initial activity. According to SDS-PAGE the molecular mass of the MnP was 40 kDa. The optimal pH and temperature were found to be 4.5 and $35^{\circ}C$, respectively. The enzyme was stable even after exposure to a pH range of 4.5 to 6.0, and at temperatures of up to $35^{\circ}C$ at a pH of 4.5 for 1h. The $K_m$ and $V_{max}$ values for the substrate phenol red were found to be $8{\mu}m$ and 111.14 U/mg of protein, respectively. The MnP also oxidized other substrates such as guaiacol, DMP, and veratryl alcohol. Sodium azide, EDTA, SDS, $Cu^{2+}$, and $Fe^{2+}$, at 1-5 mM, strongly inhibited enzyme activity, whereas $Ca^{2+}$ and $Zn^{2+}$ increased enzyme activity. The participation of the purified enzyme in the decolorization of dyes suggests that S. ostrea manganese peroxidase could be effectively employed in textile industries.

• The Korean Journal of Mycology
• /
• v.35 no.1
• /
• pp.37-42
• /
• 2007

The mushroom Lentinus lepideus was used to produce mycelial as well as soluble polysaccharides in bioreactor cultures. To determine optimal submerged culture conditions, both growth characteristics and water soluble polysaccharides production were compared among four different types of bioreactor and culture conditions. For the production of mycelial biomass, the following bioreactors were proven to be effective in decreasing order: an external-loop type air-lift bioreactor (ETAB; 7g/l), a balloon type air bubble bioreactor (BTBB; 6.2g/l), a stirrer type bioreactor (STB; 6g/l), and a column type air bubble bioreactor (CTBB; 5g/l). Maxiaml production of water soluble exopolysaccharides (EPS; 0.62g/l) and endopolysaccharides (PPS; 7.7%) could also be obtained from BTBB. The mycelial biomass increased with increase in glucose concentration from 15g/l to 75g/l in the media. In contrast, PPS contents in the cells decreased with increase in glucose concentration in the media, showing the highest PPS content (7%) at 15g/l. Among different medium feeding types, fed-batch culture based on concentration control in media (10g/l) produced higher mycelia than fed-batch culture based on volume control of media (5.8g/l) or batch culture (3.4g/l). EPS production was also higher in fed-batch culture based on medium concentration control than that in other feeding types.

• Journal of Conservation Science
• /
• v.28 no.4
• /
• pp.411-416
• /
• 2012

The purpose of this study was to analyze AMS radiocarbon dating, using wiggle match, of a charcoal column excavated from a fired dwelling site (ra-#8) at the Pungnaptoseong earthen wall made in Baekje era. The result of wiggle matching for 6 decadal single-ring samples of the charcoal produced ${\pm}2{\sigma}$ radiocarbon date (95.4% confidence interval) as A.D. 190~280. It indicated that the dwelling site (ra-#8) belonged to the early and middle of the 3rd century. Radiocarbon dating results confirmed the date speculated by archaeologists according to dwelling structure and pottery style.

• Journal of the Korean Wood Science and Technology
• /
• v.2 no.2
• /
• pp.8-12
• /
• 1974

1. If one unity is given to the prongs whose ends touch each other for estimating the internal stresses occuring in it, the internal stresses which are developed in the open prongs can be evaluated by the ratio to the unity. In accordance with the above statement, an equation was derived as follows. For employing this equation, the prongs should be made as shown in Fig. I, and be measured A and B' as indicated in Fig. l. A more precise value will result as the angle (J becomes smaller. $CH=\frac{(A-B') (4W+A) (4W-A)}{2A[(2W+(A-B')][2W-(A-B')]}{\times}100%$ where A is thickness of the prong, B' is the distance between the two prongs shown in Fig. 1 and CH is the value of internal stress expressed by percentage. It precision is not required, the equation can be simplified as follows. $CH=\frac{A-B'}{A}{\times}200%$ 2. Under scheduled drying condition III the kiln, when the weight of a sample board is constant, the moisture content of the shell of a sample board in the case of a normal casehardening is lower than that of the equilibrium moisture content which is indicated by the Forest Products Laboratory, U. S. Department of Agriculture. This result is usually true, especially in a thin sample board. A thick unseasoned or reverse casehardened sample does not follow in the above statement. 3. The results in the comparison of drying rate with five different kinds of wood given in Table 1 show that the these drying rates, i.e., the quantity of water evaporated from the surface area of I centimeter square per hour, are graded by the order of their magnitude as follows. (1) Ginkgo biloba Linne (2) Diospyros Kaki Thumberg. (3) Pinus densiflora Sieb. et Zucc. (4) Larix kaempheri Sargent (5) Castanea crenata Sieb. et Zucc. It is shown, for example, that at the moisture content of 20 percent the highest value revealed by the Ginkgo biloba is in the order of 3.8 times as great as that for Castanea crenata Sieb. & Zucc. which has the lowest value. Especially below the moisture content of 26 percent, the drying rate, i.e., the function of moisture content in percentage, is represented by the linear equation. All of these linear equations are highly significant in testing the confficient of X i. e., moisture content in percentage. In the Table 2, the symbols are expressed as follows; Y is the quantity of water evaporated from the surface area of 1 centimeter square per hour, and X is the moisture content of the percentage. The drying rate is plotted against the moisture content of the percentage as in Fig. 2. 4. One hundred times the ratio(P%) of the number of samples occuring in the CH 4 class (from 76 to 100% of CH ratio) within the total number of saplmes tested to those of the total which underlie the given SR ratio is measured in Table 3. (The 9% indicated above is assumed as the danger probability in percentage). In summarizing above results, the conclusion is in Table 4. NOTE: In Table 4, the column numbers such as 1. 2 and 3 imply as follows, respectively. 1) The minimum SR ratio which does not reveal the CH 4, class is indicated as in the column 1. 2) The extent of SR ratio which is confined in the safety allowance of 30 percent is shown in the column 2. 3) The lowest limitation of SR ratio which gives the most danger probability of 100 percent is shown in column 3. In analyzing above results, it is clear that chestnut and larch easly form internal stress in comparison with persimmon and pine. However, in considering the fact that the revers, casehardening occured in fir and ginkgo, under the same drying condition with the others, it is deduced that fir and ginkgo form normal casehardening with difficulty in comparison with the other species tested. 5. All kinds of drying defects except casehardening are developed when the internal stresses are in excess of the ultimate strength of material in the case of long-lime loading. Under the drying condition at temperature of $170^{\circ}F$ and the lower humidity. the drying defects are not so severe. However, under the same conditions at $200^{\circ}F$, the lower humidity and not end coated, all sample boards develop severe drying defects. Especially the chestnut was very prone to form the drying defects such as casehardening and splitting.

• Journal of Korea Foresty Energy
• /
• v.19 no.2
• /
• pp.93-101
• /
• 2000

Wood of Robinia pseudoacacia and bark of Populus alba$\times$P. glandulosa, Fraxinus rhynchophylla and Ulmus davidiana var. japonica were collected and extracted with acetone-water(7:3, v/v) in glass jar to examine whether its bioactive compounds exist. The concentrated extracts were fractionated with hexane, chloroform, ethylacetate and water, and then freeze-dried for column chromatography and bioactive tests. The isolated compounds were sakuranetin-5-O-$\beta$-D-glucopyranoside from Populus alba $\times$Pl glandulosa, 4--ethyoxy-(+)-leucorobinetinidin frm R. pseudoacacia and fraxetion from F. rhynchophylla and were characterized by $^1H$ and$^{13}C $ NMR and positive FAB-MS. Decay-resistant activity was expressed by weight loss ratio and hyphae growth inhibition in the wood dust agar medium inoculated wood rot fungi. R. pseudoacacia showed best anti-decaying property in both test and its methanol untreated samples, indicating higher activity than methanol treated samples in hyphae grwoth test. In antioxidative test, $\alpha$-tocopherol, one of natural antioxidants, and BHT, one of synthetic antioxidants, were used as references to cmpare with the antioxidant activities of the extacted fractions. Ethylacetate fraction of F. rhynchophylla bark indicated the hightest activity in this test and all fractions of R. pseudiacacia extractives also indicated higher activities compared with the other fractions. In the isolated compounds, aesculetin isolated from F. rhynchophylla bark showed best activity and followed by robonetinidin from R. pseudoacaica.

• Korean Journal of Heritage: History & Science
• /
• v.56 no.4
• /
• pp.192-214
• /
• 2023

Wooden architectural cultural heritages are one of the visible legacies that show the national's identity. Even when the concept of 'the original' of cultural heritages was not accurately understood, the emphasis of preservation and management of cultural heritages was placed on 'preservation of the original form' or 'maintenance of the original form'. Moreover, these days, following the trend of international preservation principles, cultural heritages are considered important as "values as historical objects." This paper is the result of an attempt to determine the scope and content of what parts should be monitored to maintain the original form of wooden architectural cultural heritage. The first thing to be done in monitoring wooden architectural cultural heritage is to check the condition of the ground and foundation. The second is the column. This is because the instability of the column causes damage to the joint with each member and the fitting part, resulting in physical changes leading to damage to the wall. The third is monitor the roof tiles. If the leak continues into the building due to the separation or damage of the roof, the defect should be partially dismantled and repaired, so it should be monitored to maintain its original shape as much as possible. The monitoring range of the base, column, and roof serves as a reference point for identifying what damage is being done to the relevant cultural heritages. In other words, the data at the time when monitoring began becomes the 'original' for the year. Alternatives based on the analysis of monitoring for the preservation of original cultural heritages should be actively introduced. In addition, by sharing the current state and situation of cultural heritages as a result of monitoring with various related organizations, preventive preservation should be established rather than preservation of cultural heritages by "intervention."