• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.4
• /
• pp.251-257
• /
• 2015

This work presents modelling and simulation of a readout integrated circuit (ROIC) design considering pair-wise serial configuration along with thermal modeling of an uncooled microbolometer array. A fully differential approach is used at the input stage in order to reduce fixed pattern noise due to the process variation and self-heating-related issues. Each pair of microbolometers is pulse-biased such that they both fall under the same self-heating point along the self-heating trend line. A ${\pm}10%$ process variation is considered. The proposed design is simulated with a reference input image consisting of an array of $127{\times}92$ pixels. This configuration uses only one unity gain differential amplifier along with a single 14-bit analog-to-digital converter in order to minimize the dynamic range requirement of the ROIC.

• Transactions of Materials Processing
• /
• v.22 no.1
• /
• pp.48-53
• /
• 2013

As the adoption of injection molding technology increases, injected-molded optical products require higher dimensional accuracy and optical stability than ever before. In the present study, four kinds of molding methods, i.e., conventional injection molding (CIM), injection/compression molding (ICM), rapid heat and cooling the mold(RHCM) and rapid injection/compression molding (RICM) were selected in order to investigate the optical anisotropy of a 7 inch Light Guide Plate(LGP) by examining the gap-wise distribution of birefringence and the extinction angle. The results indicate that the compression process can decrease flow-induced birefringence over the whole region and that rapid heating can decrease the birefringence level better than conventional molding. In addition, for the combination of compression and rapid heating a reversal flow was detected from the distribution of the extinction angle near the gate.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.3
• /
• pp.198-204
• /
• 1993

The study is concerned with finite element analysis and design of axisymmetric deep drawing by local heating. When the bottom shape of a cup is not flat but in complex-shaped, i.e., hemispherical, the cup cannot be drawn in one or two processes in the conventional deep drawing process and the limit drawing ratio is limited as well. By introducing local heating selectively with regards to the heating position, the formability of the sheet metal can be greatly increased with the reduced number of processes. In the Process analysisthe rigid- viscoplastic finite element method is employed and the temperature effect is incorporated. Bishop's step-wise decoupled method is employed to analyze the thermomechanical interaction between deformation and heat transfer. Axisymmetric deep drawing of a hemisphere-bottomed cup has been analyzed for various combinations of heat application in the punch and the die. At the first stage of deep drawing stretch forming is practically carried out by firmly pressing the blankholder with the punch and the die heated at various levels of temperature. Then at the second stage the same cup is drawn for the saame or different combination of temperature. From the computation, it has thus been shown that the fromability of a cup is greatly increased in two-stage deep drawing with increased limet drawing ratio.

• Transactions of Materials Processing
• /
• v.19 no.1
• /
• pp.50-58
• /
• 2010

In order to successfully implement hot die forging process for the large-size titanium alloy products, it is necessary to devise a customized heating method for the billets and the die tools, as well as the die tool design. This study aims at establishing a hot die forging process of the large-size titanium alloy container products by applying the warm die, semi-hot die and hot die forging process step-wise. To accomplish this purpose, forging mechanism and the die tools were designed considering the strength of die materials at the given die heating temperature. The movable heating devices for the billet and the die tools were also introduced to prevent overcooling of billet and die tools. To verify the applicability of the designed forging process, real-size forging tests were carried out and the quality of forged products, including dimension, surface condition, microstructure and the mechanical properties was evaluated.

• Journal of the Korean Society of Visualization
• /
• v.7 no.1
• /
• pp.3-8
• /
• 2009

Most vehicles have a heating, ventilating and air conditioning (HVAC) device to control the thermal condition and to make comfortable environment in the passenger compartment. The improvement of ventilation flow inside the passenger compartment is crucial for providing comfortable environment. For this, better understanding on the variation of flow characteristics of ventilation air inside the passenger compartment with respect to various ventilation modes is strongly required. Most previous studies on the ventilation flow in a car cabin were carried out using computational fluid dynamics (CFD) analysis or scale-down water-model experiments. In this study, whole ventilation flow discharged from the air vent of a real passenger car was measured using a special PIV (particle image velocimetry) system for large-size FOV (field of view). Under real recirculation ventilation condition, the spatial distributions of stream-wise turbulence intensity and mean velocity were measured in the vortical panel-duct center plane under the panel ventilation mode. These experimental data would be useful for understanding the detailed flow structure of real ventilation flow and validating numerical predictions.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.14 no.5
• /
• pp.1119-1128
• /
• 1990

A numerical method for analyzing non-isothermal, rigid-viscoplastic deformation problems has been presented. As an application, a stretch forming of sheet metals, including temperature effect, has been analyzed by a three-dimensional finite element method. Bishop`s step-wise decoupled method is adopted to solve thermomechanical coupling between deformation and heat transfer. Using the method, the effect of temperature on strain distribution during stretch forming is investigated. By comparison of the non-isothermal results with isothermal analysis, the importance of including temperature effects in the analysis of metal forming problems is emphasized. The predicted results were in good agreement with the existing experimental measurements at the different punch temperatures and dome heights investigated. It is also found that any increase of the punch temperature appeared to postpone the strain localization process by lowering the peak strain in the critical punch-sheet contact region and by normalizing strain distribution within the specimen.

• The Bulletin of The Korean Astronomical Society
• /
• v.39 no.1
• /
• pp.67.2-67.2
• /
• 2014

Comet nucleus is a solid body consisting of dark dust grains and ice. Cometary volatiles sublimate from subsurface layer by solar heating, leaving behind large dust grains on the surface. Eventually, the appearance could turn into asteroidal rather than cometary. It is, therefore, expected that there would be "dormant comets" in the list of known asteroids. Our research group has undertaken the research on the population of dormant comets. We applied a brand-new asteroidal catalog compiled from data garnered by three infrared astronomical observatories, AKARI, IRAS and WISE. We extracted objects which have comet-like orbits on the basis of their orbital properties (Tisserand parameters with respect to Jupiter, TJ, and aphelion distance, Q). We found that (1) there are a considerable number (>100) of asteroids in comet-like orbits, and (2) 80% of them have low albedo consistent with comets. This result suggest that these low albedo objects could be dormant comets. One unanticipated finding is that 20% of asteroids in comet-like orbit have high albedo similar to S-type asteroids. It is difficult to explain the population of S-type asteroids in comet-like orbits by the classical mechanics theory. We further found that these high-albedo objects are small (D < 2 km) bodies distributed in near-Earth space. We suggest that such high-albedo, small, near-Earth asteroids are susceptible to Yarkovsky effect and injected into comet-like orbits.

• Journal of Ship and Ocean Technology
• /
• v.12 no.3
• /
• pp.1-13
• /
• 2008

In shipbuilding, diverse manufacturing techniques for automation have been developed and used in practice. Among them, however, the hull forming automation is the one that has not been of major concern compared with others such as welding and cutting. The basis of the development of this process is to find out how to extract thermal forming information. There exist various methods to obtain such information and the 3D design shape that needs to be formed should be extracted first for getting the necessary thermal forming information. Except well-established shipyards which operate 3D design systems, most of the shipyards only rely on 2.5D design systems and do not have an easy way to obtain 3D surface design data. So in this study, various shipbuilding design systems used by shipyards are investigated and a 3D design surface data extraction method is proposed from those design systems. Then an example is presented to show the extraction of real 3D surface data using the proposed method and computation of thermal forming information using the data.

• Journal of Korean Society of Rural Planning
• /
• v.9 no.4 s.21
• /
• pp.35-41
• /
• 2003

The purpose of this study is on identifying the function of ground temperature arrangement of village grove. Case study was accomplished at Hacho village grove in Jinan-gun, Jeonbuk province. Hacho village grove was the largest grove of all and most formal grove in Jinan region. So ground temperature of outside and inside of Hacho village grove were measured from March to October in 2001. And comparative review about difference between outside and inside of village grove was accomplished. Our ancestors, in spite of orient and occident, have made a settlement in consideration of climatic conditions. We have to team from past pattern and add modern scientific technology. So traditional wisdom and wise planning process must be considered in order to create qualitative residential environment in present through natural elements. It is identified that in winter, the inner side ground temperature is higher than outside one of that and in summer, in contrary, the inner side one of that is lower than outside one of that. So it is identified that Macho village grove breaks winds and reduce the heating energy in winter, it reduces ground temperature and reduces cooling energy very well in summer. It is identified that village grove reduce ground temperature in summer better than any other season. It is identified that in summer, the effect of maintaining constant temperature is also better than my other season. So it is identified that village grove stabilize most changeable outside temperature in inside of that.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2008.11a
• /
• pp.199-203
• /
• 2008

With recent trend in domestic and global market requiring architectures' conversion into skyscrapers seasoned with the features of landmarks, structural problems in relation with explosive spatting during fire emergencies are arising as controversial issues. Accordingly, many productive researches have been made in relation to the reinforcement techniques for improving fire resistance and the number of applications in the field is gradually increasing. In this study, a ductile outline form using ECC (Engineered Cementations Composites) was made with improvements on the structure and fire resistance to examine its applicability. Also, currently in Japan, the number of studies and applications is increasing focusing on reduction of construction time and improvement of workability with application of Half-PCa method. However, using such method of construction, large structural members decrease the utilization of space and architecture-wise, there is a disadvantage of the weight increase. Therefore, in such context, it would be worth reducing the weight of the structural members by reducing the size using ECC. In addition, its excellent pseudo strain-hardening due to fiber may have great effects on seismic designs. In the mean time, this study planned 3 equal conditions for mix water, PVA fiber and additives excluding binder and refractory to evaluate the mechanical properties of resistance against pressure and internal force. Finally, an evaluation was executed on the fire resistance of the newly made ductile outline form. As a result, from ECC-I to ECC-III, all showed excellent mechanical properties due to pseudo strain-hardening and in the fire resistance test conducted with ISO 834 heating curve, most of them tended to be in the range of the reference temperature (538℃-180min), so there was no occurrence of any explosive spatting.