• Elastomers and Composites
• /
• v.55 no.3
• /
• pp.229-234
• /
• 2020

Automobile wiper blades are generally treated with chlorine to lower their friction coefficient with the windshield surface. This treatment could affect the crosslink density measurement of rubber vulcanizates, a material used in windshield wipers, which would consequently alter its chemical and physical properties. Therefore, this study evaluated the influence of chlorination on crosslink density measurements of natural rubber (NR) vulcanizates using a vehicle wiper blade. A method for determining the degree of chlorination was developed where the interaction parameter between the rubber and the swelling solvent was corrected. A decrease in the rubber sample swelling ratio was observed upon chlorination, and the chlorination penetrated less than 1% of the sample thickness. The chlorinated NR was assumed to be chloroprene rubber (CR), which was used to correct the interaction parameter. The results showed the CR contributed approximately 7% to the parameter.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.05a
• /
• pp.835-836
• /
• 2010

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2009.06a
• /
• pp.157-158
• /
• 2009

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.24 no.5
• /
• pp.374-380
• /
• 2014

This article proposes a design guideline to reduce squeal noise generated by an automobile wiper blade. In order to explain the squeal noise phenomenon, a source of squeal noise is experimentally investigated using a rotating disk equipment, and then a single-degree-of-freedom stick-slip vibration model is established for a blade tip. Based on analytical results, we discuss a tendency of the squeal noise for various physical parameters.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.3
• /
• pp.292-298
• /
• 2015

A wiper is a safety device removing rain and debris from windshield and ensuring visibility of drivers. If contact pressure distribution between rubber of the blade and the windshield is unbalanced, unwanted noise, vibration, and abrasion of the blade can occur and sometimes fatal accidents could occur. To improve the safety of the wiper, there have been many researches on the contact pressure analysis of the wiper, but the analysis results were not converged or require much computational time due to material nonlinearity of the rubber and contact conditions between the blade rubber and the windshield. In this research, a simple model with 1D beam and 2D shell elements was used for the contact pressure analysis instead of the 3D blade model. The simplified model saved computational time of the analysis and resolved convergence problems. The accuracy of the analysis results was verified by comparing them with experimental results for different rail spring curvatures.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1998.10a
• /
• pp.221-226
• /
• 1998

The processing conditions for the mass production of platelet WS$_2$ lubricant powder were optimized. The mixture of tungsten and sulfur powders was sealed in a vacuum of 10$^{-3}$ torr and heat-treated at 850$\circ$C for 2 h. The internal pressure of reaction chamber was maintained at certain level by controlling the release valve automatically. The reaction product was the platelet WS$_2$ powder with an average size of 15 $\mu$m. The synthesized WS$_2$ powder was then coated on the wiper-blade of automobiles and the commercial deep-grooved ball bearing using wet and dry coating methods, respectively. High lubricity and wear resistance of wet coated wiper-blade were confirmed by the life test of 70,000 cycles. The life-time of the ball bearing assembled after WS$_2$ coating onto each part increased 50 times compared to the non-coated ball bearing.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.4
• /
• pp.79-83
• /
• 2010

Recently, the flat wiper which is one piece wiper and subjected to a pressing force at a single center point is gaining wide applications on automotive windshields. However, nonuniform reactive pressure distributions takes place, so that wiping is not completed at such locations. The wiping performance of the flat wiper is best when a wiper and a curved windshield have perfect contact without gaps under the specified pressing force of 13 ~ 15 gf/cm. Therefore, it is necessary that the realistic curvature equation of a wiper spring-rail should be obtained. Finite element analysis, CATIA script-macro function, and the least square method were utilized to find out the curvature of a spring-rail for a perfect contact with a windshield under a specified concentrated load. The curvature equation became the third order polynomial.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.4
• /
• pp.465-472
• /
• 2008

An automotive windshield wiper system is modeled mainly for vibration analysis purpose. The model is composed of solid links, ideal joints, imperfect joints to simulate unavoidable manufacturing defects and bushings having stiffness, contact between a wiper blade and a wind screen glass, friction, a spring and an actuator. Main stream of wiper dynamics analysis has been obtaining a closed form of system of equations using Newton's or Lagrange's formula and doing a numerical simulation study to understand and predict the behavior of it. However, the modeling process is complex since a wiper system is of multibody and a contact problem occurs. When imperfection, such as dead zone of a joint and stiffness of a rubber bushing, should be included, the added complexity makes the modeling difficult. Since the imperfection is understood as main cause of problematic vibration, the dynamics model of a wiper system aiming vibration analysis should include such unavoidable manufacturing defects in the model. An open form of dynamic model of a automotive windshield wiper system with imperfect joints using a commercial software is obtained and a simulation analyssis is conducted for vibration reduction study.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.3292-3297
• /
• 2014

The vehicle wiper blade(W/B) to lower the friction coefficient of the rubber surface after the surface treatment with chlorine were investigated. IR spectrum from W/B was used to determine the extent of chlorination of the rubber surface. Coefficient of friction is significantly reduced by the treatment with chlorine. In particular, the more sensitive influence on the initial chlorination. Rubber surface properties with respect to the longitudinal direction of the cutting plane were obtained by EPMA line analysis results. Penetration depth by EPMA chlorine concentration($20.0{\ell}$ of water for 35.0% hydrochloric acid(HCl) $300m{\ell}$ with 5.25% sodium hypochlorite(NaOCl) $400m{\ell}$), the chlorine treatment for 5 minutes was conducted to find that after 1.2 ${\mu}m$.

• Elastomers and Composites
• /
• v.33 no.1
• /
• pp.27-36
• /
• 1998

The surface of wiper blade(W/B) rubber was chlorinated by chemical treatment method using the hydrochloric acid(HCI) and sodium hypochlorite(NaOCl). From the results of contact angle measurement, friction coefficient measurement, and ATR-IR spectra, the surface characteristics of chlorinated W/B rubber with time of chlorination were studied. Contact angles for W/B rubber with increasing time of chlorination and chlorine concentration were measured for the water and ethylene glycol. From the results, contact angle fell rapidly with increasing time of chlorination and chlorine concentration, reaching a constant value after about 10min. And the wettability of W/B rubber surface by means of chlorination has been improved. For an unchlorinated W/B rubber, the friction coefficient with time of chlorination decreased from 1.27 to 0.20~0.23 on full chlorination. As the results it was considered that abrasion resistance of W/B rubber surface has been also improved. The values of pH and $Cl^-$ ion concentration in a chlorine treatment solution decreased as the extent of chlorination of W/B rubber surface increased. From the results of ATR-IR spectra, it was observed that C=C double band of W/B rubber surface transformed into C-Cl band, but quantitative determination of the extent of chlorination was not feasible because of the complexity of chlorination reactions.