• Journal of the Society of Naval Architects of Korea
• /
• v.47 no.5
• /
• pp.697-702
• /
• 2010

A WIG(Wing-In-Ground effect) craft flies close to the water surface by utilizing a cushion of relatively high pressurized air between its wing and water surface. This implies that when one designs such craft it is important to have lightweight structures with adequate strength to resist external loads with some margins. To investigate this requirement, this paper deals with the structural analysis of the bottom plate of small WIG craft having a design landing weight of 1.2-ton. As building materials for the WIG craft, pre-preg carbon/epoxy composites are considered. The strength information of the bottom plate is obtained using the first-ply-failure analysis in conjunction with a mid-plane symmetric laminated plate theory. As a result, the first-ply-failure location, load and deflection of the bottom plate are obtained. The calculated strength information is compared with the water reaction load for the bottom plate of seaplanes considered when they land on the water surface -the same fluid-structure interaction mechanism as that of WIG craft. In the calculation of seaplane water reaction load information, the rules shown in FAR(Federal Aviation Regulations) Part 25 are used. Through the comparison, the structural integrity of the bottom plate for the WIG craft is checked.

• Proceedings of The Korean Cleft Lip And Palate Association
• /
• 2002.05a
• /
• pp.27-27
• /
• 2002

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.14 no.1
• /
• pp.22-27
• /
• 2006

The linear and nonlinear aeroelastic analyses of a flat plate wing with flaperon have been performed by using frequency-domain and time-domain analyses. Natural modes from free vibration analysis and a doublet-hybrid method (DHM) are used for the computation of subsonic unsteady aerodynamic forces. The flaperon hinge is represented by a free-play spring and is linearized by the described function method. The linear and nonlinear flutter analyses indicate that flapping mode of the flaperon, the hinge stiffness and free-play of hinge have significant effects on the aeroelastic characteristics. From the nonlinear flutter analysis, different modes like stable and unstable limit-cycle-oscillation are observed in same flutter velocity depending on initial conditions.

• Korean journal of applied entomology
• /
• v.56 no.4
• /
• pp.435-436
• /
• 2017

Subgena and clypeus are a continuous plate, so should be collectively called as peristoma. Subsequently, subgenal sulcus is revised into peristomal sulcus or cranio-stomal sulcus. Ptilinal suture on dipteran adult head is revised into ptilinal fissure. Notal and pleural wing processes are revised into notal and pleural process, respectively. The lower plate of abdomen is ventum, while that of thorax is sternum.

• Journal of the Society of Naval Architects of Korea
• /
• v.35 no.3
• /
• pp.14-25
• /
• 1998

This paper describes the numerical modelling for the steady and unsteady forces of 3-D wings flying near the free surface based on a potential based panel method. For the steady problem where a wing flies over the fixed float surface, steady lift and drag forces are calculated for wings with and without end-plates having different sections, angle of attacks, aspect patios and flying heights. These numerical results are compared with the wind tunnel test results. The unsteady problem is treated as a boundary value one where a wing flies over the described wavy surface. The unsteady lift force variations of a wing due to different wave lengths and heights are calculated at different flying heights.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.9 no.3
• /
• pp.84-91
• /
• 2001

Comparison between performance of a plate fin and that of a modified plate fin is investigated as a function of the position, the non-dimensional width and height of wings as well as the non-dimensional fin length using a two-dimensional separation of variables method. The ratio of the incremental rate of heat loss to that of the area of a modified plate fin is also presented as a function of the height of wings. The modified plate fin is made by attaching the wings to upper and lower sides of a plate fin. One of the results shows that performance of a modified plate fin is more improved as the wings approach left (higher) thermal reservoir.

• International Journal of Aeronautical and Space Sciences
• /
• v.4 no.1
• /
• pp.63-74
• /
• 2003

The vortical flow of a 65-deg flat plate delta wing with a leading edge extension(LEX) was examined through off-surface visualization, 5-hole probe and hot-film measurements. The off-surface flow visualization technique used micro water droplets generated by a home-style ultrasonic humidifier and a laser beam sheet. The angles of attack ranged from 10 to 30 degrees, and the sideslip angles ranged from 0 to -15 degrees. The Reynolds number was $1.82{\times}10^5$ for the flow visualization, and $1.76{\times}10^6$ for the 5-hole probe and hot-film measurements. The comparison of the visualization photos and the flow field measurement showed that the two results were in a good agreement for the relative position and the structure of the wing and LEX vortices, even though the flow Reynolds numbers of the two results were much different. The wing vortex and the LEX vortex coil each other while maintaining a comparable strength and identity at zero sideslip. Neither a looping of the wing vortex around the strake vortex, nor the lopsided coiling of the stronger strake and the weaker wing vortices was observed. At non-zero sideslip, the downward movement of the LEX vortex when going downstream was enhanced on the windward side, and the downward and inboard movement of the LEX vortex when going downstream was suppressed on the leeward side. The counterclockwise coiling of the wing and LEX vortices was decreased significantly on the leeward side.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2010.05a
• /
• pp.175-176
• /
• 2010

Current Bridge Specification for Highway Bridges adopts a simplified method to determine sectional forces of abutment wing by diving its area into four sections. This simplified method was developed when numerical analysis was not mature and computer resources were expensive. It has been criticized that the simplified method produces conservative results. This study evaluates the problem of current design practice to improve the design guideline for abutment wing.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.12
• /
• pp.1511-1520
• /
• 2004

A flow visualization of the two-dimensional rigid fling-clap motions of the flat-plate wing are performed to gain knowledge of butterfly mechanisms that might be employed by butterflies during flight. In this numerical visualization, the time-dependent Navier-Stokes equations are solved for cyclic fling and clap types of wing motion. The separation vortex pair that is developed in the fling phase of the cyclic fling and clap motion is observed to be stronger than those of the fling followed by clap and pause motion(1st cycle motion). This stronger separation vortex pair in the fling phase is attributable to the separation vortex pair of the outside space developed in the clap phase as it moves into the opening in the following fling phase. Accordingly, higher lift and power expenditure coefficients in the fling after clap phase is caused by the stronger separation vortex pair.

• Computers and Concrete
• /
• v.23 no.5
• /
• pp.361-376
• /
• 2019

In this research, bending analysis of a micro sandwich skew plate with isotropic core and piezoelectric composite face sheets reinforced by carbon nanotube on the elastic foundations are studied. The classical plate theory (CPT) are used to model micro sandwich skew plate and to apply size dependent effects based on modified strain gradient theory. Eshelby-Mori-Tanaka approach is considered for the effective mechanical properties of the nanocomposite face sheets. The governing equations of equilibrium are derived using minimum principle of total potential energy and then solved by extended Kantorovich method (EKM). The effects of width to thickness ratio and length to width of the sandwich plate, core-to-face sheet thickness ratio, the material length scale parameters, volume fraction of CNT, the angle of skew plate, different boundary conditions and types of cores on the deflection of micro sandwich skew plate are investigated. One of the most important results is the reduction of the deflection by increasing the angle of the micro sandwich skew plate and decreasing the deflection by decreasing the thickness of the structural core. The results of this research can be used in modern construction in the form of reinforced slabs or stiffened plates and also used in construction of bridges, the wing of airplane.