• Journal of Drive and Control
• /
• v.10 no.3
• /
• pp.1-6
• /
• 2013

Traction control suppresses the spinning of the driven wheel during drive away or acceleration on slippery road condition. In this study, the estimation method of brake pressure hardly measured is proposed. The estimation method of brake pressure and the brake pressure control with pulse width modulation(PWM) are verified a good performance through experiment. Also, the vehicle simulation on slippery road conditions is validated the applicability of brake pressure control for traction control. The simulation results have showed that the brake pressure can be used the control variable for traction control.

• International Journal of Korean Welding Society
• /
• v.3 no.2
• /
• pp.15-23
• /
• 2003

A genetic algorithm was applied to an arc welding process to determine near optimal settings of welding process parameters which produce good weld quality. This method searches for optimal settings of welding parameters through systematic experiments without a model between input and output variables. It has an advantage of being able to find optimal conditions with a fewer number of experiments than conventional full factorial design. A genetic algorithm was applied to optimization of weld bead geometry. In the optimization problem, the input variables were wire feed rate, welding voltage, and welding speed, root opening and the output variables were bead height, bead width, penetration and back bead width. The number of level for each input variable is 8, 16, 8 and 3, respectively. Therefore, according to the conventional full factorial design, in order to find the optimal welding conditions, 3,072 experiments must be performed. The genetic algorithm, however, found the near optimal welding conditions from less than 48 experiments.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.10
• /
• pp.41-50
• /
• 1998

In this study, to investigate a characteristics of slip ratio control of H.C.U for ABS, half car model tester were developed and a new H.C.U. was compactly designed comparing to the commercical H.C.U. for ABS. In half car model tester, variable inertia wheel has been used to load the car weights and braking forces according to the road surface conditions which were realized by pneumatic cylinder. And solenoid valves using P.W.M. (Pulse Width Modulation) method were installed in the new H.C.U The slip ratio characteristics of tire had been measured using half car model tester and the results were used in the control simulation for a new H.C.U.

• Journal of Institute of Control, Robotics and Systems
• /
• v.9 no.1
• /
• pp.73-81
• /
• 2003

An autonomous stair robot recognizing the stair, and climbing up and down the stair by utilizing a robot vision, photo sensors, and appropriate climbing algorithm is introduced. Four arms associated with four wheels make the robot climb up and down more safely and faster than a simple track typed robot. The robot can adjust wheel base according to the stair width, hence it can adopt to a variable width stair with different algorithms in climbing up and down. The command and image data acquired from the robot are transferred to the main computer through RF wireless modules, and the data are delivered to a remote computer via a network communication through a proper data compression, thus, the real time image monitoring is implemented effectively.

• Proceedings of the KIEE Conference
• /
• 1998.07a
• /
• pp.46-48
• /
• 1998

This paper introduces the design method of a variable reluctace liner pulse motor to be analysed by a 3-dimensional problem in the 2-dimension. And it shows the thrust force density with respect to the ratio of the slot width to the teeth width, the height of mover and the height of tooth.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.5
• /
• pp.150-156
• /
• 1997

Three dimensional finite element analysis was conducted to estimate the effect of shape parameters (plate width and thickness) on the stress intensity factor for crack in the integrally stiffened plate. Analysis was done for width ratios of 0.5, 0.75, 1.0, 1.5, 2.0, 2.5, and thickness ratios of 2, 3, 4, 6. Based on these results, an empirical equation of geometry factor is formulated as a function of crack length and thickness ratio.

• Journal of Biosystems Engineering
• /
• v.36 no.1
• /
• pp.15-22
• /
• 2011

An experimental variable rate nursery sprayer was developed to adjust application rates for canopy volume in real time. The sprayer consisted of two vertical booms integrated with ultrasonic sensors, and variable rate nozzles coupled with pulse width modulation (PMW) based solenoid valves. A custom-designed microcontroller instructed the sensors to detect canopy size and occurrence and then controlled nozzles to achieve variable application rates. A spray delivery system, which consisted of diaphragm pump, pressure regulator and 4-cycle gasoline engine, offered the spray discharge function. Spray delay time, time adjustment in spray trigger for the leading distance of the sensor, was measured with a high-speed camera, and it was from 50 to 140 ms earlier than the desired time (398 ms) at 3.2 km/h under indoor conditions. Consequently, the sprayer triggered 4.5 to 12.5 cm prior to detected targets. Duty cycles of the sprayer were from 20 to 34 ms for senor-to-canopy (STC) distance from 0.30 to 0.76 m. Outdoor test confirmed that the nozzles were triggered from 290 to 380 ms after detecting tree canopy at 3.2 km/h. The spray rate of the new sprayer was 58.4 to 85.2% of the constant application rate (935 L/ha). Spray coverage was collected at four areas of evergreen canopy by water sensitive papers (WSP), and ranged from 1.9 to 41.1% and 1.8 to 34.7% for variable and constant rate applications, respectively. One WSP area had significant (P < 0.05) difference in mean spray coverage between two application conditions.

• Journal of Navigation and Port Research
• /
• v.29 no.1 s.97
• /
• pp.9-15
• /
• 2005

To design ship channel is one of important factors for planning and developing a port. In most case, the core factors for designing ship channel are the layout and width of channel provided the net underkeel clearance is secured to be safe enough to pass. In this study, Variable Bumper Area(VBA) model is applied to design and assess ship channel. This model reflects ship's particular, ship domain theory, ship speed and mariner's ship handling skill and experience, especially external forces which cause leeway, set and drift and the change of ship maneuvering characteristics. A real time, full mission shiphandling simulator is used to analyze ship dynamic data according to mariner's ship control, external forces, ete. This model defines Domain degree and Domain-index for assessing the efficiency and safety of the channel. The proposed model is applied to Ulsan new port plan which has a channel width of 1.5 times the length of the largest vessel, a radius of 5 times the length of the largest vessel in a curve of 57 degree centerline angle and SBM facility adjacent to the lateral edge of channel. The result of this study shows that the width of the channel and radius of channel curve are suitable for the target ship but the difficulty of ship handling is caused by the large course change and SBM located in the vicinity of channel.

• Proceedings of the IEEK Conference
• /
• 2004.06a
• /
• pp.321-324
• /
• 2004

In this paper, attenuation characteristics of silica-based variable optical attenuator (VOA) with heat insulating structures are investigated by variations of structural parameters and heating power at wavelength 1.55${\mu}m$. The characteristics of power dissipation and attenuation at this VOA was optimized in terms of heating insulating width, under-cladding height and over-cladding height. The optimized maximum attenuation of this VOA was achieved about 31dB at heating power 150mW.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.145-147
• /
• 1996

Traction Motor is being transferred to the squirrel cage induction motor from D.C motor, by the improved power semiconductors like GTO, IGBT, etc. In the Induction Motor, inverter system must be used for delivering variable voltage variable frequency. But, by pulsating in the system the harmonics would be produced, and that cause the torque ripple and enfeeble the dynamic characteristics of the motor. So, to use the inverter system, we should take the torque ripple into consideration. To minimize the torque ripple in the VSI fed Traction Motor, the optimal pulsating was presented in this paper. By using the SPWM(Sinusoidal Pulse Width Modulation) method, feeding the appropriate pulse, we can minimize the torque ripple and improve the transient response.