• Journal of the Semiconductor & Display Technology
• /
• v.14 no.4
• /
• pp.72-77
• /
• 2015

Three-level diode clamped multilevel inverter, generally known as neutral point clamped (NPC) inverter, has an inherent problem causing neutral point (NP) potential variation. Until now, the NP potential problem of variation has been investigated and lots of solutions have also been proposed. This paper presents a neutral point voltage control technology using the anti-windup PI controller and offset technology of PWM (Pulse Width Modulation) to control the variation of NPC 3-phase three-level inverter neutral point voltage. And the proposed algorithm is tested and verified using a PLL (Phase Locked Loop) in order to synchronize the phase voltage from the line voltage of grid. It significantly improves the voltage balancing under a solar fluctuation conditions of the inverter. Experimental results show the good performance and effectiveness of the proposed method.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.5 no.1
• /
• pp.15-20
• /
• 1995

Fuzzy membership functions are some kinds of mapping function for the fuzzification and the defuzzification. Triangle-shaped fuzzy membership functions are widely used in fuzzy controller, for it is easy to implement. In these membership functions, it is known that narrower fuzzy sets permit finer control near the operating point than that far from the operating point. $Supp{\acute{o}}se$ we have a membership function with narrower triangle near zero and wider triangle far from zero. The membership function will make fine control when small input is given and rough control at large input. Therefore the performance of the controller with that membership function will be enhanced. This paper presents how the width of triangle base in the fuzzy membership function has influence on the output using geometrical approaches.

• Journal of Electrical Engineering and Technology
• /
• v.9 no.4
• /
• pp.1269-1276
• /
• 2014

The main objective of this paper is to design DC-DC MPPT circuit using chaotic pulse width modulation to track maximum power from solar PV module for space application. The direct control method of tracking is used to extract maximum power. The nominal duty cycle of the main switch of DC-DC SEPIC converter is adjusted so that the solar panel output impedance is equal to the input resistance of the SEPIC converter which results better spectral performance in the tracked voltages when compared to conventional PWM control. The conversion efficiency of the proposed MPPT system is increased when CPWM is used as a control scheme

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.2B no.4
• /
• pp.201-206
• /
• 2002

The paper presents the component parts and their models of the Switched Reluctance motor drive system with the angle position-current chopping control and with the fixed angle pulse width modulation control. The calculation of the parameters and the simulated models based on the MATLAB SIMULINK software package are introduced by a four-phase 816 structure prototype with the four-phase asymmetric bridge power converter. The simulation of the prototype in the course of starting is made by the simulated models at the different control strategies and the different given rotor speed.

• Journal of Power Electronics
• /
• v.2 no.2
• /
• pp.130-138
• /
• 2002

The windup phenomenon appears and degrades control performance when a controller with integrating action is used and plant input is limited. An anti-windup integal-proportional(IP) controller is proposed for the variable-speed moter drives and it is experimentally applied to the speed control of a vector-controlled induction moter driven by a pulse width modulated (PWM) voltage source inverter (VSI). The consistency range of the IP controller is firstly derived and the intergal state is controlled to salisfy always the consistency range according to whether the the controller output is saturated or not. Although the operating condition like moter load or speed command is changed under the limited plant input, It is expermentally verified that the speed response has much improved performance, such as no overshoot and fast settling time, and the maximmum plant input is also effectively utilized.

• Journal of Power Electronics
• /
• v.16 no.1
• /
• pp.142-152
• /
• 2016

Common mode voltage (CMV) generation is a major problem in switching power converter fed induction motor drive systems. CMV is the zero sequence voltage generated due to the switching action of power converters. Even a small magnitude of CMV with a high rate of change may circulate large bearing currents which may damage a machine's bearings and shorten its life. There are several methods of controlling CMV. This paper presents 3-level sinusoidal pulse width modulation based techniques to control the magnitude and rate of change of CMV in multilevel AC-DC-AC drive systems. Simulation and experimental investigations have been presented to validate the performance of proposed technique to control CMV in 3-level neutral point clamped inverter based AC-DC-AC system.

• Journal of Power Electronics
• /
• v.16 no.1
• /
• pp.57-65
• /
• 2016

Reverse matrix converters, which can step up voltages, are suitable for applications with source voltages that are lower than load voltages, such as generator systems. Reverse matrix converter topologies are advantageous because they do not require additional components to conventional matrix converters. In this paper, a detection method and a post-fault modulation strategy to operate a converter as close as possible to its desired normal operation under the open-switch fault condition in the rectifier stage are proposed. An open-switch fault in the rectifier stage of a reverse matrix converter causes current distortions and voltage ripples in the system. Therefore, fault-tolerant control for open-switch faults is required to improve the reliability of a system. The proposed strategy determines the appropriate switching stages from among the remaining healthy switches of the converter. This is done based on reference currents or voltages. The performance of the proposed strategy is experimentally verified.

• Proceedings of the KIEE Conference
• /
• 2003.07b
• /
• pp.1211-1213
• /
• 2003

A pulse width modulation(PWM) method for single-phase Sepic-type rectifier is introduced in this paper. The characteristics of the proposed PWM system are high performance high power factor with low input current harmonic distortion. The proposed control method is based on the average-current-mode using the dedicated integrated circuit UC3854 this technique it is possible to implement a very simple control circuit for unitary power-factor in CCM operation and also to provide over-current protection.

• Proceedings of the KIEE Conference
• /
• 2000.11b
• /
• pp.372-374
• /
• 2000

This paper presents a study on the indirect FOC (field oriented control) of induction motor using TMS320F240. This DSP has become possible to design and implement a highly efficient and accurate AC induction drive control. This paper describes a pulse width modulator based on the voltage space vectors technique that accepts voltage demands in dq coordinates and generates three-phase PWM waveforms to drive a variable frequency voltage-source inverter. The Current Model lock is added to generate the rotor flux angular speed.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2010.05a
• /
• pp.574-576
• /
• 2010

In this paper, we propose a development of high speed inspection system which allows the inspection of width, definition and flaws in lead-frame using CCD camera. This system consists of the parts of lighting, inspection, lighting control, GUI and more and developed techniques used are lighting control, fast inspection algorithm and advanced measurement technique for improvement in resolution. The effectiveness in proposed method is proved by conducting field tests.