• KIEAE Journal
• /
• v.7 no.3
• /
• pp.89-96
• /
• 2007

The purpose of this experimental study is to investigate the compressive strength, shear strength, bending strength, and crack control by the mixture of the hwang-toh. The size of compressive specimens is $200{\times}200{\times}400(mm)$, and the size of shear, bending specimens is $200{\times}200{\times}600(mm)$. Finally, crack control specimens for comparative comparison is $200{\times}200{\times}15(mm)$. The mixture of the hwang-toh is as follows; Hwangtoh( H)+Water(W), H+W+Sand(S), H+W+S+sTraw(0.5%), H+W+S+sT(1.0%). The actual height, width, and the length are measured at the center of all specimens. The main parameters are mixture ratio of hwang-toh, straw and age of specimens. The test results are as follows. (1) The compressive strength is linearly increased until 15 weeks according to specimen ages. (2) About crack control, the specimen added in 1% straw is the most effective.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.308-310
• /
• 2001

This paper investigates a novel speed sensorless control method of I.M considering the secondary resistance identification based on the transientless torque control technique. Especially, this paper aimed at the identification of the secondary resistance simultaneously with speed estimation superposing of sinusoidal flux wave to a constant flux value. Furthermore, the secondary flux with some frequency is controlled independently on torque control. The proposed speed estimation method is derived from a motor circuit equation theoretically and also it can be conducted easily by detecting primary motor currents and primary voltage commands at every sampling time. Some numerical simulations with the assumption of using a pulse width modulation(PWM) voltage source inverter are performed to verify the proposed method.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.1034-1036
• /
• 2006

In this paper, I used microprocessor and sensor and designed to improve the efficiency of the photovoltaic system the photovoltaic position tracker device, and compared the normal photovoltaic system of fixed form with the photovoltaic system of solar position tracked form. Moreover, compared the catalogue of solar cell module and the simulation through a mathematics modelling with the solar cell's characteristic interpreting and, composed an power conversion system with boost converter and voltage source inverter. Used the constant voltage control method for maximum power point tracking in boost converter control and, used the SPWM(Sinusoidal Pulse Width Modulation) control method in inverter control.

• International Journal of Fluid Machinery and Systems
• /
• v.4 no.1
• /
• pp.97-103
• /
• 2011

With the aim to increase blade loadings and stable operating range in highly loaded compressors, this article has been conducted to explore, through a numerical parametric study, the potential of passive control using slotted bladings in cascade configurations. The objective of this numerical investigation is to analyze the influence of location, width and slope of the slots and therefore identify the optimal configuration. The approach is based on two dimensional cascade geometry, low speed regime, steady state and turbulent RANS model. The results show the efficiency of this passive technique to delay separation and enhance aerodynamic performances of the compressor cascade. A maximum of 28.3% reduction in loss coefficient have been reached, the flow turning is increased with approximately $5^0$ and high loading over a wide range of angle of attack have been obtained for the optimized control parameter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.1
• /
• pp.27-33
• /
• 2016

A pulse-width modulation (PWM) method for common mode noise reduction in a PWM inverter connected to a single-phase grid is proposed in this study. The extensively used conventional switching method may experience common mode voltage problems, which generate current leakage and electromagnetic induction problems. In the proposed switching method, the neutral point of the output voltage is always fixed at both ends of the input voltage to reduce common mode noise. The validity of the proposed method is proven through simulation and experimental results.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1248-1250
• /
• 2000

The aim of this paper is to present a review of recently used current control technique for three-phase voltage source pulse-width modulated converters. Various technique, different in concept, three current control methods are presented in this paper. Current -control methods to be applied in system are PI controller. Predictive current controller. Minimum-time current controller respectively. In initial state and transient state, the response characteristics of three current control methods are verified through simulations.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.1177-1181
• /
• 2000

Usually, in many applications. high frequency resonant inverters are used, and the PAM(Pulse Amplitude Modulation), PFM(Pulse Frequency Modulation) or PWM(Pulse Width Modulation) techniques are used to control the output power of resonant inverters. And the resonant inverters have to control the output frequency for the reliable operation under the variable load conditions. In this paper, a new switching scheme is proposed as a resonant frequency following control of resonant inverters. With the proposed method. it can be obtained that optimum resonant frequency and unity output displacement factor under the variable resonant frequency adaptively. The detail algorithm of the proposed switching scheme and its characteristics are discussed. And the veridity of the proposed method is confirmed with the experimental results.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1211-1213
• /
• 2004

CCFL(cold cathode fluorescent lamp) are used to backlight of LCD(liquid crystal display). CCFL dimming methods are used to pulse frequency modulation(PFM) or pulse width modulation(PWM). In this paper, design of CCFL driving and control circuit by half-bridge type series and parallel resonant inverter that variable frequency modulation method to control the output voltage current. Inverter switching frequency is higher than resonant frequency for stable operating, and it is possible dimming control. On the basis of equivalent circuit, the validity of this study is confirmed by the comparison of simulation and experimental result.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.53 no.2
• /
• pp.123-128
• /
• 2004

Recently with the development of power switching device and DSP which has perip -heral devices to control AC servo system, the servo technology has met a new development opportunity. In this study, a DSP based AC servo system with a 3-phase PMSM is proposed. The newly produced DSP TMX320F2812 version C which has the performance of fast speed, 150MIPS, and rich peripheral interface is used. Also space vector pulse width modulation (SVPWM) and the digital PI control are implemented to the servo control system.

• Proceedings of the KIPE Conference
• /
• 2007.07a
• /
• pp.441-443
• /
• 2007

In this paper, The authors design the current controller which independently control the d, q axis current transformed by the synchronously rotating d, q axis and a Space Vector Pulse Width Modulation(SVPWM) to steadily control the output DC-Link voltage against the variable load of the three phase PWM converter. Also, This study improves the high power factor, stability, and rapid response by the phase angle control using the digital Phase Locked Loop(PLL).