• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.6
• /
• pp.488-493
• /
• 2014

This paper presents a carrier-based pulse-width modulation(PWM) method for reducing the common-mode voltage of a three-level four-leg converter. The idea of the proposed PWM method is intuitive and easy to be implemented in digital signal processor-based converter control systems. On the basis of the analysis of space-vector PWM(SVPWM) and sinusoidal PWM(SPWM) switching patterns, the fourth leg pole voltage of the three-phase converter called "f leg pole voltage" is manipulated to reduce the common-mode voltage. To synthesize f leg pole voltage for the suppression of the common-mode voltage, positive and negative pole voltage references of f leg are calculated. An offset voltage is also deduced to prevent the distortion of a, b, and c phase voltages. The feasibility of the proposed PWM method is verified by simulation and experimental results. The common-mode voltage of the proposed PWM method in peak-to-peak value is 33% in comparison with that of the conventional SVPWM method. The transition number of the common-mode voltage is also reduced to 25%.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.17 no.1
• /
• pp.182-189
• /
• 2009

The noise from the sunroof can be divided into the low frequency buffeting noise and the high frequency turbulence noise generated when a car runs at the high driving speed. The wind deflector suppresses the buffeting noise generation by accelerating the vortex shedding from the front edge of sunroof opening, and guides the flow direction so that air can pass smoothly over the sunroof opening. To reduce the buffeting noise and the high frequency noise, it is very important to locate a deflector in a proper position depending on the driving speed and the sunroof opening width. The deflector's sectional shape also plays an important role in efficiently reducing the buffeting and high frequency noise. In this paper, we determined the optimum deflector's sectional shape and examined the flow characteristics behind a sunroof deflector through CFD analysis with changing the deflector height, the driving speed and the sunroof opening width. It is found that the deflector needs to be located in the higher location to control the buffeting noise by shedding the higher frequency vortices to accelerating vortices from the sunroof front edge. The deflector may act as a new noise source at the high driving speed, then it is desirable to put the deflector at the proper height to reduce the flow fluctuations and the noise generation. We also made a road test to verify CFD analysis results in this study.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.28 no.2
• /
• pp.71-74
• /
• 2008

To investigate the sulfate utilization efficiency in different rape (Brassica napus) cultivars, sulfate uptake are analyzed under complete S-supply level (2.0mM ${SO_4}^{2-}$). This study used ten different genotypes of rape (Mokpo, Tamra, Youngsan, Naehan, Saturnin, Akela, Mosa, Capitol, Pollen and Colosse). For comparison of ${SO_4}^{2-}$ uptake among 10 cultivars, leaf number, leaf length and width, root length was also observed. Leaf length and width in all cultivars less variable among the cultivars examined. The longest root was shown in Saturnin (36.3 cm). ${SO_4}^{2-}$ uptake in Saturnin, Youngsan and Mokpo was significantly higher whereas that of Mosa and Pollen was relativety lower. Saturnin and Mokpo which have a high ${SO_4}^{2-}$ uptake exhibited a high ${NO_3}^-$ uptake.

• Progress in Superconductivity and Cryogenics
• /
• v.14 no.3
• /
• pp.9-12
• /
• 2012

Usually, the AC loss from the superconducting element of an SFCL due to the load current is very small because it is composed of the combination of bifilar windings with very small reactance. Although the AC loss is small enough, we should be albe to predict for the design and control of the cryogenic system. In fact, an SFCL for the transmission voltage class may not generate ignorable AC loss because of the inevitable space between the HTS wires for the high voltage insulation and cryogenic efficiency. To measure the AC loss dependency on the space between the 2G HTS wires with the width of 4.4 mm, we prepared an experimental setup which could adjust the distance between the wires. We used two 500-mm length HTS wires in parallel and applied the current in the opposite direction for each wire to simulate a part of a current limiting module for a high voltage SFCL. We also put two couples of voltage taps at the ends of each wire and a cancel coil in the voltage measurement circuit to compensate the reactive component from the voltage taps. In this condition, we varied the distance between the wires to investigate the change of the transport current loss. A similar experimental study with HTS wire with the width of 12 mm is now in progress.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.4
• /
• pp.431-440
• /
• 2012

In this paper, new beam-forming array antenna is proposed. The proposed beam-forming array antenna has control ability for beam-direction/width by employing low loss reconfigurable power divide and three-dimensional array structure. The reconfigurable power divider is key idea in the proposed antenna, because it has reconfigurable RF power distribution ability to each antenna. And, for research and verification of the proposed antenna, 3-dimensional beam-forming array antenna is implemented, and the experimental results show that the proposed antenna has various radiation modes from 1:1 to 1:N by adjusting RF power distribution.

• Restorative Dentistry and Endodontics
• /
• v.16 no.1
• /
• pp.74-86
• /
• 1991

The purpose of this study was to evaluate the resulting root canal angulation and shape change after using various enlarging instruments. The mesial canals (120) of extracted human mandibular 1st and 2nd molars were randomly divided into 6 groups; Control, K-type me, Heliapical me, Canal Master me, sonic and ultrasonic instrumentation group. Vertical angulation of each canal was determined by a straight line through the long axis of canal and another straight line through the apical foramen to intersect at the point where the canal began to leave the long axis of the tooth. By recording and comparing the measured angles of the each set of pre-and postinstrumentation. Then, the roots were sectioned horizontally in the apical, middle, coronal thirds and the canal shapes examined, as was the mesiodistal canal diameter as it relates to the external root surface. The results were as follows: 1. Instrumentation using K-type me group resulted in the highest mean change in angulation ($9.900^{\circ}$) (p < 0.005), while Sonic Air MM 3000 group resulted in the least degree of straightening canals ($8.250^{\circ}$) (p < 0.005). 2. Canal Master file group resulted in the best canal shape at the three levels (P < 0.005). 3. Measured minimal mesial root width produced Heliapical me group at the apical 1/3 level, Sonic Air MM 3000 group at the middle 1/3 level, Heliapical me group at the coronal 1/3 level (P < 0.005). 4. Measured minimal distal root width produced Sonic Air MM 3000 group at the apical 1/3 level (P < 0.05), Heliapical me group at the middle 1/3 level (P < 0.005), Canal Master me group at the coronal 1/3 level (P < 0.005). 5. HeIiapical me group produced more increased canal diameter than any other groups (P < 0.005).

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.10
• /
• pp.581-586
• /
• 2002

To improve the current waveform of diode rectifiers, we propose a new operating principle for the voltage-doubler diode rectifiers. In the conventional voltage-doubler rectifier circuit, relatively large capacitors are used to boost the output voltage, while the proposed circuit uses smaller ones and a small reactor not to boost the output voltage but improve the input current waveform. A circuit design method is shown by experimentation and confirmed simulation. The experimental results of the proposed diode rectifier satisfies the harmonic guide lines. A high input power factor of 97(%) and an efficiency of 98[%] are also obtained. The new rectifier with no controlled switches meet the harmonic guide lines, resulting in a simple, reliable and low-cost at-to dc converters in comparison with the boost-type current-improving circuits. This paper proposes a nonlinear impedance circuit composed by diodes and inductors or capacitors. This circuit needs no control circuits and switches, and the impedance value is changed by the polarity of current or voltage. And this paper presents one of these applications to improve the input current of capacitor input diode rectifiers. The rectifier using the nonlinear impedance circuit is constructed with four diodes and four capacitors in addition to the conventional rectifiers, that is, it has eight diodes and five capacitors, including a DC link capacitor. It makes harmonic components of the input current reduction and the power factor improvement. Half pulse-width modulated (HPWM) inverter was explained compared with conventional pulse width modulated(PWM) inverter. Proposed HPWM inverter eliminated dead-time by lowering switching loss and holding over-shooting.

• Journal of International Academy of Physical Therapy Research
• /
• v.7 no.2
• /
• pp.1025-1030
• /
• 2016

The purpose of this study was to investigate the effects of combined wedge on the range of motion in ankle and knee joint, ankle eversion moment and knee adduction moment, and center of pressure excursion of foot for genu varus among adult men during gait. This study was carried out with 10 adult men for genu varus in a motion analysis laboratory in J university. The subjects of the experiment were measured above 5cm width between the knees on contact of both medial malleolus of ankle while standing. The width of their knees in neutral position was measured without the inversion or eversion of the subtalar joint by the investigator. The subjects of the experiment were ten who were conducted randomly for standard insole, insole with $10^{\circ}$ lateral on rear foot wedge, insole at $10^{\circ}$lateral on rear foot and $5^{\circ}$ medial on fore foot wedge. Before and after intervention, changes on the range of motion in ankle and knee joint, ankle eversion moment and knee adduction moment, and center of pressure excursion were measured. In order to compare analyses among groups; repeated one-way ANOVA and $Scheff{\acute{e}}$ post hoc test were used. As a result, combined wedge group was significantly decreased compared to control wedge group in terms of knee varus angle in mid-stance(p<.05). Combined wedge group was significantly decreased compared to lateral wedge group in terms of ankle eversion moment in whole stance(p<.05). Combined wedge group was significantly decreased compared to lateral wedge group in terms of knee adduction moment in whole stance(p<.05). Combined wedge group was significantly decreased compared to lateral wedge in terms of center of pressure excursion in whole stance(p<.05). The results of this study suggest that combined wedge for genu varus decreased ankle eversion moment and knee adduction moment upon center of pressure excursion. We hypothesize that combined wedge may also be effective in the protection excessive ankle pronation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.6
• /
• pp.39-44
• /
• 2011

This purpose of this study is to propose the characteristics analysis of the PCB pattern designed two modes for the output voltage value on the PMIC through converting the limited voltage value inputted from a battery. The PCB design technology has been undergoing difficulty in getting the related technology in a domestic market because of increasing EMI/EMC, Cross-talk, Impedance. And it requires to have the appropriate clearance between the patterns and the technology of PCB pattern width with a amperage according to various uses. The study carried out the characteristics analysis of the PCB pattern designed from a direct output method without a capacitor[mode1], to an output method through a capacitor[mode2] for PMIC output voltage value. Besides, we calculated the pattern width with a amperage using the equation suggested by IPC-2221, presenting the right way of the layout design to analyze the trouble with the test. Therefore, this study is expected to contribute not only to applying the PMIC design for the mobile panel power supply, but also helping the design and application technology in various areas such as car control, camera, note-book, computer, PDA, etc.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.8
• /
• pp.15-27
• /
• 2008

In this paper, an EBG(Electromagnetic BandGap) resonator antenna with a stripline type FSS(Frequency Selective Surface) superstrate for PCS-band base station antennas is proposed. The characteristics of resonant frequency and -3dB bandwidth of a unit cell of a superstrate are first analyzed by varing several design parameters such as a strip width and a unit cell width in order to design an EBG resonator antenna satisfying the required antenna gain and bandwidth for PCS-band base station antennas. Among various unit cell shapes, strip dipole and stripline are considered and their characteristics are compared. It was found that a resonant length of the EBG resonator antenna becomes smaller when the stripline shape is used and the control of the bandwidth is also much easier. By using the unit cell simulation results, planar and cylindrical EBG resonator antennas at PCS-band are designed.