• Journal of Welding and Joining
• /
• v.23 no.4
• /
• pp.66-72
• /
• 2005

An electromagnetic inductive sensor consisted of one exciter and three separated (triple) detectors has been developed for both tracking the weld seam of a workpiece and controlling the sensor-to-workpiece distance (height) simultaneously. The left and right detectors are used to track the seam, while the fore and the other two detectors allow the sensor to determine the height and the gap width by being coupled their outputs together. A series of experiments with the proposed sensor located above a mild steel plate containing a weld seam of gap are carried out to examine the feasibility of the sensor. The results revealed that the proposed sensor could fairly well track the desired seam and also well control the height to be constant even when the gap width of the seam varied. The gap width can be also determined during the seam tracking by using the sensor outputs. As a consequence, these can provide the developed sensor with substantial improvement for industrial uses with respect to the previous electromagnetic sensors being used for the weld seam tracking.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.285-288
• /
• 1996

The electronic operation of the gas discharge tube is controlled by the electrical energy as sinusoidal waveform in arbitrary frequency range, or as a sequence of pulses at a wide range of duty cycle, the gas composition, the kind of electrode and the vessel geometry. In this paper, the pulsed mode operated gas discharge tube is composed with mixed gas of IIg-Ne ( 10 Torr ), in the tube of 15.0 mm outer diameter and has variable color from red to blue with changing frequency and pulse width in high voltage. As increasing pulse width and frequency in the gas discharge tube, the phenomenons that the electron temperature in the positive column increases and the radiation from atoms of higher upper state energy levels increases, exist. The color have the locus from red (0.4972, 0.3128) to blue (0.2736, 0.2619) in CIE chromacity diagram with increasing pulse width and frequency. The changing method of pulse width and frequency has been shown to be suitable for the luminous color control.

• Journal of the Korea Concrete Institute
• /
• v.18 no.4 s.94
• /
• pp.543-552
• /
• 2006

The current design for crack width control in concrete bridges is incomplete in analytical models. As one of the important serviceability limit states, the crack width be considered with the quantitative prediction of the initiation and propagation of corrosion and corrosion-induced cracking. A serviceability limit state of cracking can be affected by the combined effects of bond, slip, cracking, and corrosion of the reinforcing elements. Considering life span of concrete bridges, an improved prediction of crack width affected by time-dependent general corrosion has been proposed for the crack control design. The developed corrosion models and crack width prediction equation can be used for the design and the maintenance of prestressed and non-prestressed reinforcements by varying time, w/c, cover depth, and geometries of the sections. It can also be used as the rational criteria for the maintenance of existing concrete bridges and the prediction of remaining life of concrete structures.

• Journal of Periodontal and Implant Science
• /
• v.31 no.2
• /
• pp.477-488
• /
• 2001

The present study evaluated of regeneration effect of platelet rich plasma on the treatment of grade II furcation involvement, with coralline calcium phosphate bone in humans. 30 teeth with grade II furcation defect were selected and 15 teeth(control) were treated with coralline calcium phosphate bone, the others(test) were treated with coralline calcium phosphate bone and platelet rich plasma. Pocket depth, clinical attachment level, width of keratinized gingiva width were measured at baseline, postoperative 3, 6months. from cementoenamel junction to alveolar crest and fundus were measured at baseline, 6months(re-entry). Both groups were statistically analyzed by Wilcoxon signed Ranks Test & Mann-whitney Test using SPSS program(5% significance level). The results were as follows: 1. Pocket depth, clinical attachment level, keratinized gingva width, cementoenamel junction - alveolar crest, cementoenamel junction - fundus were not differ significantly in both groups at baseline 2. The change of pocket depth, clinical attachment level, keratinized gingva width, cementoenamel junction - alveolar crest, cementoenamel junction - fundus in both groups were decreased significantly at 3, 6months(p<0.05). 3. The change of pocket depth, clinical attachment level in test group decreased significantly than control at 3, 6months(p<0.05). 4. The change of keratinized gingiva width, cementoenamel junctional - alveolar crest, cementoenamel junction - fundus were not differ significantly in both groups at 3, 6months. 5. The pocket depth, clinical attachment level, keratinized gingiva width exhibited marked changes at 3 months in both groups. In conclusion, the results of this study suggest that platelet rich plasma have adjunctive clinical treatment effect to periodontal regeneration in grade II furcation defects.

• Journal of Institute of Control, Robotics and Systems
• /
• v.16 no.10
• /
• pp.1006-1012
• /
• 2010

The hot rolling process ranks the highest position for production in steel making process. The hot strip manufacturing processes consist of the reheating furnace, roughing and finishing mill and coiler. The reheating furnace heats the slab. The roughing and finishing mill produce the hot strip from slab. The hot strip quality mainly depends on finishing mill, which consists of 4-high 7 stands. The looper is installed between stands and is used for controlling the strip tension by the looper angle for better material flow. It is difficult to control the strip tension with the coupled looper system from interaction between the looper angle and strip tension. Too much deviation of strip tension severely affects the poor width quality of the hot strip. It is important to control simultaneously both the looper angle and strip tension with each of their target values. This paper proposes the fuzzy tension control, which is developed to minimize the width deviation of the hot strip by maintaining the proper strip tension between stands and to achieve the stable operation of the coupled looper system. The fuzzy tension control performance is compared with the conventional PID control by experimental results.

• Journal of Bio-Environment Control
• /
• v.8 no.1
• /
• pp.67-73
• /
• 1999

This experiment was conducted to investigate the effect of thermokeeping bag with 30 and 45cm width on the growth, fruit quality and yield of oriental melon. Difference of the highest temperature was not observed but the lowest temperature of thermokeeping bag with 30cm and 45cm width was higher than that of control by 0.9$^{\circ}C$ and 1.8$^{\circ}C$, respectively The highest soil temperature of thermokeeping bag with 30cm and 45cm width was higher than that of control by 1.9$^{\circ}C$ and 9.9$^{\circ}C$, respectively and the lowest soil temperature of thermokeeping bag with 30cm and 45cm width was higher than that of control by 0.9$^{\circ}C$ and 1.2$^{\circ}C$, respectively. Growth characteristics in terms of stem length, leaf number, leaf area, fresh and dry weight, fruit weight, flesh thickness and soluble solid were higher as the width of thermokeeping bag was winder. Marketable yield per 10a of 30 and 45cm thermokeeping bag was higher 5.3% and 19.2% than that of control with 996.4kg per 0.1ha.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.3
• /
• pp.485-501
• /
• 1997

Pressure control is possible driving a simple ON/OFF 3-way valve of hydraulic servo system by pulse width modulation signal. But the pressure varies according to the duty ratio and carrier frequency and repeated on-off action induces pressure fluctuation. So equations for mean pressure and ripple amplitude are theoretically derived as a function of on/off time, the system parameters which decide the pressure characteristics are arranged and they are verified by experimental study. As the result selection criteria for the major design parameters are established and the basic strategy to suppress the unnecessary fluctuation can be provided for a hydraulic pressure control system using these type of valves.

• Journal of Power Electronics
• /
• v.14 no.2
• /
• pp.302-314
• /
• 2014

Due to advancements in power electronics and inverter topologies, the current controlled multilevel voltage-source pulse width modulated (PWM) inverter is usually preferred for accurate control, quick response and high dynamic performance. A multilevel topology approach is found to be best suited for overcoming many problems arising from the use of high power converters. This paper presents a comprehensive review and comparative study of several current control (CC) techniques for multilevel inverters with a special emphasis on various approaches of the hysteresis current controller. Since the hysteresis CC technique poses a problem of variable switching frequency, a ramp-comparator controller and a predictive controller to attain constant switching frequency are described along with its quantitative comparison. Furthermore, various methods have been reviewed to achieve hysteresis current control PWM with constant switching frequency operation. This paper complies various guidelines to choose a particular method suitable for application at a given power level, switching frequency and dynamic response.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1149-1153
• /
• 2006

We developed the equipment palpating cell proliferation using a high brightness LED. This equipment was fabricated using a micro-controller and a high brightness LED, and designed to enable us to control light irradiation time, intensity, frequency and so on. Especially, to control the light irradiation frequency, FPGA was used, and to control the change of output value, TLC5941 was used. Control stage is divided into 30 levels by program. Consequently, the current value could be controlled by the change of level in Continue Wave(CW) and Pulse Width Modulation(PWM), and the output of a high brightness LED could be controlled stage by stage.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.107-111
• /
• 1997

Pressure control is possible by pulse width modulation signal driving a simple ON/OFF 2-way valve of hydraulic servo system. But it indices pressure fluctuation due to repeated on-off action and the pressure varies according to the duty ratio and carrier frequency. So mean pressure and ripple amplitude are arranged by experimental study as the driving signal change which decides the pressure characteristics. As the result selection criteria of the major design parameters may be established and the basic strategy to suppress the unnecessary flucturion may be provided for a hydraulic pressure control system.