• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.668-673
• /
• 2000

Spud angle( ${\alpha}$ ) and fuel injection angle ( ${\beta}$ ) have strong influence on spud type gas burner combustion. A wide range of flame stability is shown at ${\alpha}=60^{\circ}$, but at ${\alpha}=30^{\circ}$ is narrow. Optimum condition of flame stability swirl angle( ${\gamma}$ ) is $40^{\circ}$. At condition of ${\alpha}=30^{\circ}$ flame shape is relatively narrow and long, on the other hand, at ${\alpha}=60^{\circ}$ flame is wide and short. Regardless of spud angle, maximum flame temperature shows in the range of Z=200mm and R=0mm. Flame temperature, on the whole, is high at ${\alpha}=45^{\circ}$. At ${\alpha}=45^{\circ}$, NOx emission is higher than other conditions that may be concerned with flame temperature. At ${\beta}=60^{\circ}$ and ${\gamma}=40^{\circ}$, NOx emission is reduced due to fuel injection angle.

• Journal of the Korean Solar Energy Society
• /
• v.31 no.5
• /
• pp.85-90
• /
• 2011

The effects of $CO_2$ ppm in atmosphere on the values of the total emissivity are studied. The predictions by several methods are compared. The predicted value differences between modified Kondratyev model and Hottel model are the smallest with in the range of values tested. The $CO_2$ ppm is varied from 300 ppm to 600 ppm. By Wide Band model, the total emissivity increases with increasing density-path length product rather linearly up to 0.1 g/$cm^2$. For given $CO_2$ ppm, the total emissivity increases as the air thickness increases. The same is true for both temperature and pressure increase. The temperature range tested is 220 to 300 K. Around 260K, the total emissivity is less sensitive with increasing temperature than with decreasing temperature. The pressure is varied from 0.94 to 1.06 atm. The percentage change of total emissivity with pressure change from 1atm is at most the percentage change of the pressure.

• Korean Journal of Optics and Photonics
• /
• v.31 no.6
• /
• pp.314-320
• /
• 2020

The optics used in an infrared imaging system has a strong refractive-index change according to temperature, so an autofocus control function is essential for a military infrared imaging system with a wide operating-temperature range. In this study, we design a triple-magnification infrared imaging system, and to compensate for the change in refractive index according to temperature we measure the change in the lens focus according to temperature. The autofocus control function was implemented by using the measured movement amount, and we could obtain an image with satisfactory resolution performance over a wide range of operating temperatures.

• Journal of Sensor Science and Technology
• /
• v.26 no.1
• /
• pp.35-38
• /
• 2017

A thermally responsive hydrogel has reversibility with temperature during swelling. Here, we proposed origami inspired temperature sensor by using multi-layered hydrogel film. The formation of patterned stripes on microscale film drives bending to an angle that can be controlled linearly. Although temperature range was not wide, measured sensitivity of sensors has high resolution and accuracy. It providing a powerful platform for the design of sensitive sensors and that easily adapt other type of sensors in microscale.

• Proceedings of the Korea Society of Information Technology Applications Conference
• /
• 2005.11a
• /
• pp.103-106
• /
• 2005

This paper reports design and fabrication of CMOS temperature sensor circuit using MOSIS 0.25um CMOS technology. The proposed circuit has a temperature coefficient of $13mV/^{\circ}C$ for a wide operating temperature range with a good linearity. This circuit may be applicable to the design of one-chip IC where quartz crystal resonator is directly mounted on CMOS oscillator chips.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.255-255
• /
• 2011

Zinc oxide based thin films have been extensively studied in recent several years because they have very interesting properties and zinc oxide is non-poisonous, abundant and cheap material. ZnO films are employed in different applications like transparent conductive layers in solar cells, protective coatings and so on. Wide industrial application of the ZnO films requires of development of cheap, effective and scalable technology. Typically used technologies don't completely satisfy the industrial requirements. In the present work, we studied effect of the deposition parameters on the structure and properties of ZnO films deposited by DC arc plasmatron. The varied parameters were gas flow rates, precursor composition, substrate temperature and post-deposition annealing temperature. Vapor of Zinc acetylacetone was used as source materials, oxygen was used as working gas and argon was used as the cathode protective gas and a transport gas for the vapor. The plasmatron power was varied in the range of 700-1500 watts. Flow rate of the gases and substrate temperature rate were varied in the wide range to optimize the properties of the deposited coatings. After deposition films were annealed in the hydrogen atmosphere in the wide range of temperatures. Structure of coatings was investigated using XRD and SEM. Chemical composition was analyzed using x-ray photoelectron spectroscopy. Sheet conductivity was measured by 4-point probe method. Optical properties of the transparent ZnO-based coatings were studied by the spectroscopy. It was shown that deposition by a DC Arc plasmatron can be used for low-cost production of zinc oxide films with good optical and electrical properties. Increasing of the oxygen content in the gas mixture during deposition allow to obtain high-resistive protective and insulation coatings with high adhesion to the metallic surface.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.11
• /
• pp.2008-2013
• /
• 2006

In numerical analysis on evaluating the thermal performance of the thermal equipment, numerical values of thermodynamic properties such as temperature, pressure, specific volume, enthalpy and entropy are required. But the steam table itself cannot be used without modelling. In this study applicability of neural networks in modelling the wide temperature range of wet saturated vapor region was examined. the multi-layer neural network consists of a input layer with 1 node, two hidden layers with 10 and 20 nodes respectively and a output layer with 6 nodes. Quadratic and cubic spline interpoations methods were also applied for comparison. Neural network model revealed similar percentage error to spline interpolation. From these results, it is confirmed that the neural networks could be powerful method in modelling the wide range of the steam table.

• Journal of the Optical Society of Korea
• /
• v.8 no.3
• /
• pp.104-107
• /
• 2004

The periodic transmission spectrum of a solid etalon for wide-band capability is analyzed both theoretically and experimentally. In the transmission spectrum with an incident area of a photodetector, the peak wavelength and transmittance are deeply dependent on the incident angle and the divergence angle of the input laser beam. A thermal adjustment for a solid etalon is an optional way to control the transmission spectrum instead of the inefficient fine-angle alignment. In the result, we present the deviations of free spectral range (FSR) by the change in angle and temperature over wide wavelength range.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.342-344
• /
• 1995

Using piezoresistive effects of single-crystal and poly-crystalline silicon, pressure sensors of the same pattern were fabricated for comparison of temperature characteristics. Optimum size and aspect ratio of rectangular sensor diaphragm were calculated by FEM. For polsilicon pressure sensor, polysilicon resistors of Wheatstone bridge were deposited by LPCVD to be used in a wide' temperature range. Polysilicon pressure sensors showed more stable temperature characteristics than single-crysta1 silicon in the range of $-20\sim125[^{\circ}C]$. To get low TCO (Temperature Coefficient of Offset), below $\pm$3 [${\mu}V/V/^{\circ}C$], it is needed for each TCR of piezoresistors to have a deviation within $\pm25[ppm/^{\circ}C]$ less than $\pm500[ppm/^{\circ}C]$ of resistors for polysilicon pressure sensor can result in low TCS(Temperature Coefficient of Sensitivity) of -0.1[%FS/$^{\circ}C$].

• YAKHAK HOEJI
• /
• v.41 no.1
• /
• pp.38-47
• /
• 1997

Using a concentric cylinder type, rheometer. the steady shear flow properties of vaseline were measured over the temperature range of 20~70${\circ}$C. In this paper, the shea rate and temperature dependencies of its flow behavior were investigated and the validity of some flow models was examined. In addition, the flow characteristics over a wide temperature range were quantitatively evaluated by calculating the various material parameters. Main findings obtained from this study can be summarized as follows: (1) At relatively lower temperature range, vaseline is a plastic fluid with a yield stress and its flow behavior shows shear-thinning characteristics. (2) As the temperature increases, the value of a yield stress and the degree of shear-thinning become smaller, consequently, the Newtonian flow behavior occurs at a lower shear rate range. (3) At temperature range lower than 45${\circ}$C, the flow behavior shows much stronger temperature dependence, and a larger activation energy is needed for flow. (4) The Herschel-Bulkley model is the most effective one g$^3$ to predict the flow behavior of vaseline having a yield stress. The validity of the Bingham and Casson models becomes more available with increasing temperature. The flow behavior of vaseline at temperature range higher than 45${\circ}$C can be perfectly described by the Newton model.