• Journal of Power Electronics
• /
• 제19권1호
• /
• pp.201-210
• /
• 2019

This paper proposes a multimode hybrid control strategy that can achieve zero-voltage switching of primary switches and zero-current switching of secondary rectifier diodes in a wide input voltage range for full-bridge LLC resonant converters. When the input voltage is lower than the rated voltage, the converter operates in Mode 1 through the variable-frequency control strategy. When the input voltage is higher than the rated voltage, the converter operates in Mode 2 through the VF and phase-shift control strategy until the switching frequency reaches the upper limit. Then, the converter operates in Mode 3 through the constant-frequency and phase-shift control strategy. The secondary-side diode current will operate in the discontinuous current mode in Modes 1 and 3, whereas it will operate in the boundary current mode in Mode 2. The current RMS value and conduction loss can be reduced in Mode 2. A detailed theoretical analysis of the operation principle, the voltage gain characteristics, and the realization method is presented in this paper. Finally, a 500 W prototype with 100-200 V input voltage and 40 V output voltage is built to verify the feasibility of the multimode hybrid control strategy.

• Current Optics and Photonics
• /
• 제5권1호
• /
• pp.59-65
• /
• 2021

This paper reports a tunable diode-pumped folded intracavity Q-switched singly resonant optical parametric oscillator based on multi-period MgO:PPLN. A wide tuning mid-infrared parametric light from 2.78 ㎛ to 4.17 ㎛ was obtained in real time by changing the poled periods and temperatures. The maximum output power of 1.89 W at 3.2 ㎛, 1.53 W at 3.5 ㎛, 0.87 W at 3.8 ㎛ and 0.486 W at 4.1 ㎛ were achieved. The highest optical-optical conversion efficiency was 7.89%. During experiments, a range tunable output of 2.78-4.17 ㎛ in the mid-infrared range was achieved.

• 한국주조공학회지
• /
• 제22권5호
• /
• pp.252-256
• /
• 2002

Ni-Nb-Ti-Zr amorphous alloys were manufactured using melt-spinning methods. Amorphous formability, the supercooled liquid region before crystallization and mechanical properties were examined. The value of the reduced glass transition temperature and the supercooled liquid region of $Ni_{62}Nb_{10}Ti_{13}Zr_{15}$ alloy were relatively high and were 0.612 and 76 K respectively. However, amorphous bulk alloy rod was not formed using the Cu-mold die casting. The mechanical properties were in the range of $800{\sim}900DPN$ of hardness and $2.5{\sim}2.8$ GPa of tensile strength in the whole composition range.

• 대한화장품학회지
• /
• 제28권2호
• /
• pp.55-57
• /
• 2002

The fabrication, characterization and manipulation of nanosystems brings together physics, chemistry, materials science and biology in an unprecedented way, Phenomena occurring in such systems are fundamental to the workings of electronic devices, but also to living organisms. The ability to fabricate nanostructures is essential in the further development of functional devices that incorporate nanoscale features. Even more essential is the ability to introduce a wide range of chemical and materials flexibility into these structures to build up more complex nanostructures that can ultimately rival biological nanosystems. In this respect, polymers are potentially ideal nanoscale building blocks because of their length scale, well-defined architecture, controlled synthesis, ease of processing and wide range of chemical functionality that can be incorporated. In this presentation, we will look at a number of promising polymer-based nanofabrication strategies that have been developed recently, with an emphasis on those techniques that incorporate nanostructured polymers into devices and that exploit intrinsic polymer properties.

• Journal of Power Electronics
• /
• 제15권3호
• /
• pp.634-643
• /
• 2015

This paper presents a high frequency design approach for improving efficiency over a wide load range in the self-driven phase-shifted full-bridge converters for server power systems. In the proposed approach, a detailed ZVS analysis of the lagging leg switches in both the continuous conduction mode (CCM) and the discontinuous conduction mode (DCM) is presented. The optimum dead time and the determination of the appropriate operation mode are given for high efficiency according to the load conditions. Finally, the optimum operation conditions are defined to achieve a high-efficiency. A laboratory prototype operating at 80 kHz, rated 1 kW (12 V-83.3 A), is built to verify proposed theoretical analysis and evaluations. The experimental results show that the maximum efficiency is achieved as 95% and 83.5% at full load and 5% load conditions, respectively.

• 전기학회논문지
• /
• 제61권2호
• /
• pp.324-328
• /
• 2012

A recovered jitter of CDR(Clock and Data Recovery) Circuit based on Dual-loop DLL(Delay Locked Loop) for data recovery in high speed serial data communication is changed by depending on the input data and reference clock frequency. In this paper, 2-step DPC which has constant jitter performance for wide-range input frequency is proposed. The designed prototype 2-step CDR using proposed 2-step DPC has operation frequency between 200Mbps and 4Gbps. Average delay step of 2-step DPC is 10ps. Designed CDR circuit was tested with 0.18um CMOS process.

• Journal of Dairy Science and Biotechnology
• /
• 제38권3호
• /
• pp.142-145
• /
• 2020

Enterococcus faecalis CAUM157, isolated from raw cow's milk, is a Gram-positive, facultatively anaerobic, and non-spore-forming bacterium capable of inhabiting a wide range of environmental niches. E. faecalis CAUM157 was observed to produce a two-peptide bacteriocin that had a wide range of activity against several pathogens, including Listeria monocytogenes, Staphylococcus aureus, and periodontitis-causing bacteria. The whole genome of E. faecalis CAUM157 was sequenced using the PacBio RS II platform, revealing a genome size of 2,972,812 bp with a G+C ratio of 37.44%, assembled into two contigs. Annotation analysis revealed 2,830 coding sequences, 12 rRNAs, and 61 tRNAs. Further, in silico analysis of the genome identified a single bacteriocin gene cluster.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.195-200
• /
• 2001

An experimental study on critical heat flux (CHF) has been performed for water flow in a uniformly heated vertical 3 by 3 rod bundle under low flow and a wide range of pressure conditions. The objective of this study is to investigate the parametric trends of CHF with 3 by 3 rod bundle test section where three unheated rods exist. The general trends of the CHF are coincident with previous understandings. At low flow and system pressure above 3 MPa, some critical qualities are larger than 1.0 due to counter-current flow in test sections. Since there is a supply of water to the heated section from unheated section, the maximum CHFs at system pressure between 2 and 4 MPa are not shown.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권2호
• /
• pp.174-179
• /
• 1996

We present a new physically based analytical equation for electron effective mobility in MOS inversion layers. The new semi-empirical model is accounting expicitly for surface roughness scattering and screened Coulomb scattering in addition to phonon scattering. This model shows excellent agreement with experimentally measured effective mobility data from three different published sources for a wide range of effective transverse field, channel doping and temperature. By accounting for screened Coulomb scattering due to doping impurities in the channel, our model describes very well the roll-off of effective mobility in the low field (threshold) region for a wide range of channel doping level (Na=3.0*10$^{14}$ - 2.8*10$^{18}$ cm$^{-3}$ ).

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2003년도 춘계전력전자학술대회 논문집(1)
• /
• pp.243-246
• /
• 2003

This paper presents a new motor design well suited for an advanced exercise bike. The advanced exercise bike setup high demands for performance and physical dimensions, which is high torque, wide speed range and a diameter/length ratio around 5. These requirements makes the new motor design called an E-core Transverse Flu Machine (ETFM) vev interesting because the segmented design of the stator and rotor poles enables high diameter without increasing the flux-path and since the ETFM is similar to the switched reluctance motor, high torque and wide speed range is possible. The design of the ETFM can be peformed using a developed design program, which is also introduced in the paper. A prototype of the exercise bike with the ETFM and a classical H-bridge converter with analog current control is constructed for verification of the concept.