• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 2000.11b
• /
• pp.109-116
• /
• 2000

The objective of this study is to measure rim surface adhesion and to calculate motion resistance produced by the adhesion acting on the rim section of a circular wheel under sticky soil condition. The mechanisms of generating motion resistance by the adhesion on a circular wheel were analyzed through wheel motion. Experiments were conducted in an indoor soil bin that contains loam soil. A circular steel wheel was used for experiments. A part of the wheel rim was cut off, and transducers which can measure normal and tangential forces were installed in this section. Calculated motion resistance at a part of the rim section was superposed for one wheel rotation as motion resistance produced by the rim surface adhesion. The motion resistance increased with increasing the dynamic load. Ratio of the motion resistance to total motion resistance measured by an axis transducer was about 23 to 46 % in this study.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.7
• /
• pp.796-804
• /
• 2011

Railway vehicles are capable of indicating several types of instability. This phenomenon, which is called hunting motion, is a self excited lateral oscillation that is caused by the running velocity of the vehicle and wheel frail interactive forces. The interactive forces act to change effectively the damping characteristics of railway vehicle systems. This paper will show the impact of instability on the transfer function behavior using damping characteristics of secondary suspension. The vehicle dynamics are modeled using a 17 degree of freedom considering linear wheel/rail contact. The paper deals with certain condition of the damper characteristics that one is about various damping coefficient and another is equipped damper direction.

• Proceedings of the Korean Society for Agricultural Machinery Conference
• /
• 1993.10a
• /
• pp.1166-1175
• /
• 1993

The objective of this study is to measure contra-retractive adhesion and lift resistance acting on the rim section of a circular wheel for analyses of their effects on the dynamic load. A circular iron wheel was used for experiments. A part of the wheel rim was cut off, and transducers which can measure normal and tangential forces were installed in this section. Experiments were conducted on a laboratory soil bin which was filled with clayey soil under wet and dry conditions. The mechanism of generating contra -retractive adhesion on a circular wheel were analyzed by the experiments and motion analyses of the wheel. Effects of lift resistance on dynamic load were analyzed by measured forces under wet soil conditions in comparison in comparison with those under dry conditions. The showed that a part of the lift resistance were transferred to the dynamic load. These results may become basic data and ideas for analyses of tractor dynamic under wet soil conditions.

• Journal of the Korean Society for Railway
• /
• v.17 no.1
• /
• pp.14-18
• /
• 2014

Wheel/rail contact is a significant problem in railway dynamics. In this paper, the wheel/rail contact is examined analytically and numerically as a contact problem between two cylinders where torque and friction have effect. Furthermore, the contact of a real wheel and rail is investigated numerically where the normal and shear force act. This study demonstrates that the wheel/rail contact is a process that generates traction force through creep where rolling and sliding occurs simultaneously depending on the shape of the wheel and rail, and the friction coefficient between them.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.5
• /
• pp.100-107
• /
• 2010

This paper gives new conceptual descriptions of drag reduction mechanism owing to rotating wheel and moving ground condition when dealing with automotive aerodynamics. Using Computational Fluid Dynamics (CFD), flow simulation of three dimensional automobile configuration made by Vehicle Modeling Function (VMF) is performed and the influence of wheel arch, wheels, rotating wheel & moving ground condition to the automotive aerodynamic performance is analyzed. Finally, it is shown that rotating wheel & moving ground condition decreases automotive aerodynamic drag owing to the reduction of the induced drag led by the decrease of COANDA flow intensity of the rear trunk flow.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.6
• /
• pp.59-67
• /
• 2014

A numerical model and a controller of Active Front wheel Steer (AFS) system are designed in this study. The AFS model consists of four sub models, and the AFS controller uses sliding mode control and PID control methods. To test this model and controller an Integrated Dynamics Control with Steering (IDCS) system is also designed. The IDCS system integrates an AFS system and an ARS (Active Rear wheel Steering) system. The AFS controller and IDCS controller are compared under several driving and road conditions. An 8 degree of freedom vehicle model is also employed to test the controllers. The results show that the model of AFS system shows good kinematic steering assistance function. Steering ratio varies depends on vehicle velocity between 12 and 24. Kinematic stabilization function also shows good performance because yaw rate of AFS vehicle tracks the reference yaw rate. IDCS shows improved responses compared to AFS because body side slip angle is also reduced. This result also proves that AFS system shows satisfactory result when it is integrated with another chassis system. On a split-m road, two controllers forced the vehicle to proceed straight ahead.

• Journal of the Korean Society of Safety
• /
• v.25 no.3
• /
• pp.15-21
• /
• 2010

A differential case equipped with LSD(limited slip differential) has several advantages over a normal type for rear wheel drive vehicles. Specially, the torque distribution can be done between left and right drive wheel in the state of limited slip differential. Also although LSD types are very various according to operating type, medium and torque distribution, a multi-clutch type is generally applied to rear wheel drive vehicles. So, this study presents the analysis of design parameters for development of a friction plate for multi-clutch type LSD using vehicle road test, the simulation of analytical model and the development of vehicle dynamics model by a benchmark product. According to this investigation, the design parameters which are pre-load of coil spring, friction plate and contact area quantity, friction coefficient and TBR(torque bias ratio) for a friction plate are derived from experiment and simulation and consequently, vehicle dynamics model has been constructed for the development of friction plate for multi-clutch type LSD.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.22 no.3
• /
• pp.253-263
• /
• 2012

With the local Hertz deformation on the contact point, the dynamic contact between a high-speed wheel and an elastic beam having a gap is numerically analyzed by solving the whole equations of motion of the wheel and the beam subjected to the contact condition. For the stability of the time integration the velocity and acceleration constraints as well as the displacement constraint are imposed on the contact point. Especially the acceleration contact condition on the gap is formulated, and it is demonstrated that the contact force variation computed by the velocity contact constraint or by the acceleration contact constraint agrees well with that computed by the displacement contact constraint. The numerical examples show that, when the wheel passes on the gap, the solution is governed by the stiffness of the local Hertzian deformation.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.5
• /
• pp.12-22
• /
• 2008

In this study, the dynamic characteristics for the wheel-type landing gear system of helicopter have been analyzed. Nonlinear multi-body dynamic models of the landing gear system are constructed and the equations of motion, kinematics and internal forces of shock strut are considered. In addition, flexibility effect of the wheel axle with equivalent beam element is taken into account. General purpose commercial finite code, SAMCEF which includes MECANO module is applied. The results of dynamic simulation for various landing and weight conditions are presented and compared with each other. Based on the results, characteristics of impact dynamic behaviors of the landing gear system are practically investigated.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.67-73
• /
• 2010

In this study, a camber angle generating mechanism for rear suspension is suggested. An experimental device is implemented and tested. A full vehicle model with camber angle generating device by using ADAMS/Car is modeled. Rear left wheel and rear right wheel have 5 different camber angles in the simulations, respectively. Step steer and pulse steer simulations are carried out for investigating the effects of vehicle handling performance due to camber angle control of rear suspension. According to the results, the camber angle of rear suspension affects the vehicle handling performance during both simulations. Therefore, when the vehicle makes the right turn or left turn, left and right wheel should have the proper orientation for improving the handling performance, respectively.