• 펄프종이기술
• /
• 제47권5호
• /
• pp.134-140
• /
• 2015

This study was carried out to evaluate whether EVAc, acryl latex and biobinder could substitute the part of SB latex for pre-coating color formula or not. Different coating colors prepared through the substitution of 30% SB latex with EVAc, acryl latex, and biobinder were applied for pre-coating layer. 100% SB latex is used as a binder for top coating color. The optical properties, gloss, roughness, stiffness, dry- and wet-pick strength were measured. There were no significant differences in the brightness, whiteness, opacity, roughness, ink set-off and gloss of paper coated with 5 different coating colors. However the stiffness, dry- and wet-pick strength were somewhat lower than those of conventional coating color which 100% SB latex was used as a binder. Although the part of SB latex could be substituted with EVAc, acryl latex and biobinder without sacrificing the qualities of coated paper. Further researches on the improvement of stiffness, dry- and wet-pick strength, and the optimization of rheology of coating color in order to improve the qualities of coated paper are strongly recommended.

• 펄프종이기술
• /
• 제47권3호
• /
• pp.24-33
• /
• 2015

Linerboards containing wood flours were developed to increase solid contents in wet pressing process. Presence of wood flours in recycled fibers allowed passage of pressurized water at high wet pressing pressure, and increased solid contents while keeping the bulk of the board. The amount of wood flour addition should be controlled based on the intensity of the wet pressing pressure and the properties of the wood flours. Addition of cationic starch to the wood flour containing OCC furnish showed synergic increase of solid content and strength properties. Shapes of the wood flours such as spherical and rod type added to OCC furnish affected largely their solid content, drainage, and board physical properties.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 1999년도 Pre-symposium of the 10th ISWPC Recent Advances in Paper Science and Technology
• /
• pp.276-281
• /
• 1999

The surfaces of sheets added with N-chloro-polyacrylamide (N-Cl-PAM) are analyzed using X-ray photoelectron spectroscopy (XPS) to clarify the chemical bonding involved in the paper strength development induced by N-Cl-PAM. The comparison of the observed N1s chemical shift of the sheet with those of the paper strength additives and the model compound, 1-butyryl-3-propyl urea, illustrated the presence of covalent bonds of alkyl acyl urea and urethane on the fiber surfaces. Thus the formation of the covalent bonds by N-Cl-PAM themselves and by N-Cl-PAM with cellulose and hemicellulose may be an explanation for much higher effectiveness of N-Cl-PAM on the improvement of wet strength of paper than A-PAM.

• 한국의류학회지
• /
• 제41권4호
• /
• pp.633-645
• /
• 2017

This study examined the effects of the number of Dakji layer (a layer, two layers), the time of Jumchichigi (20, 40 and 60 minutes) and the type of Choji method making Dakji (Oebal-teugi, Ssangbal-teugi) on five strength properties of Jumchi-Hanji. As a result, the number of Dakji layer and the time of Jumchichigi influenced the five strength properties (tensile, wet tensile, tearing, bursting, and folding strengths). Jumchi-Hanjis made with two layers of Dakijis had higher properties than Jumchi-Hanjis with a layer of Dakji in the strength properties. The more the time for Jumchichigi is spent, the more the five strength properties of Jumchi-Hanji increased. The type of Choji was related to only three strength properties. The tearing strength of Jumchi-Hanjis with one and two layers, and the wet tensile and the folding strengths of Jumchi-Hanjis with two layers depended on the type of Choji. The differences of Jumchi-Hanji and Dakji were also identified in the strength properties. All Jumchi-Hanjis had low tensile and wet tensile strengths when compared to Dakjis. However, Jumchi-Hanjis, made by sixty minute Jumchchigi, had generally higher tearing, bursting, and folding strengths than the Dakjis. In conclusion, the strength properties of Jumchi-Hanji could be improved by controlling the number of Dakji layers and the time of Jumchichigi.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.695-702
• /
• 2002

Shotcrete (or Sprayed concrete) has been used as an important support material in New Austrian Tunnelling Method (NATM). Since the mid of 1990, permanent shotcrete tunnel linings such as Single-shell, NMT (Norwegian Method of Tunnelling) has been constructed in many countries for reducing the construction time and lowing construction costs instead of conventional in-situ concrete linings. Among essential technologies for successful application of permanent shotcrcte linings, high performance shotcrete providing high strength, high durability, better pumpability has to be developed in advance as an integral component. This paper presents the Ideas and first experimental attempts to increase early strength and bond strength of wet-mixed Steel Fiber Reinforced Shotcrete(SFRS) in sump water condition. In order to increase early strength, a new approach using high-early strength cement with liquid alkali-free accelerator has been investigated From the results, wet-mix SFRS with high-early strength cement and alkali-free accelerator exhibited excellent early strength improvement compared to the ordinary portland content and good bond strength even under sump water condition.

• 펄프종이기술
• /
• 제44권6호
• /
• pp.21-27
• /
• 2012

The effects of fines contents in OCC stock on the wet pressing process were evaluated in this study. The fines were collected from the beaten OCC stock by using 200 mesh. The dryness of handsheet samples after the couch and after the 1st wet press were greatly affected by the fine contents of the OCC stock. The higher contents of fines resulted in the lower value in dryness but the higher value of density followed by the higher strength properties. The addition of the retention aids and the drainage aids on the OCC stocks showed the wet pressing efficiency were greatly affected by the fine contents rather than the addition of polymer additives. The increase in the fine retention by the polymer additives offset the improvement in the wet pressing efficiency originated from the polymer additives.

• International Journal of Industrial Entomology and Biomaterials
• /
• 제16권2호
• /
• pp.61-66
• /
• 2008

In this paper, the regenerated silk fibroin (SF)/nylon 6 blend filaments were fabricated using wet spinning technique and the effect of coagulant on the post drawing and morphology of blend filaments was investigated. In the result of wet spinnability, methanol, acetone, DMF, and THF showed relatively good coagulation strength and fiber formation for the regenerated SF. On the contrary, they did not exhibit strong enough to produce a uniform nylon 6 filament due to the lack of coagulation strength. In the examination of post drawing performance, methanol showed the highest maximum draw ratio of the blend filament over all blend ratios. The maximum draw ratio of SF/nylon 6 blend filaments decreased with the reduction of SF content regardless of type of coagulant. SEM observation showed the consistent result with that of post-drawing performance. As SF content decreased, the uniform and regular structure was changed to irregular one. In particular, the severe macro-phase separation between SF and nylon 6 could be detected in the 50/50 SF/nylon 6 blend filaments coagulated in methanol and THF.

• 터널과지하공간
• /
• 제7권2호
• /
• pp.91-99
• /
• 1997

To stabilize the energy price, the more storage facilities of energy are required and among the storage methods of LPG and LNG, the method of storage at low temperature under normal confining pressure is considered. It is needed to understand the mechanical and thermal characteristics of rock under temperature variation so that the behaviors of rock can be predicted. In this paper, the variation of the rock charateristics of the Hwangdeung granite and the Boryung sandstone is studied at low temperature. The mechanical characteristics of rock under low temperatures are that as temperature decreased, unaxial compression strength and Young's modulus increased for Hwangdeung granite; strength and Young's modulus in wet condition were greater than those in dry condition. In the case of Boryung sandstone, as temperature decreases unaxial compression strength and Young's modulus increase but decrease below -10$0^{\circ}C$ in dry condition and below -16$0^{\circ}C$ in wet condtion. The mechanical characteristics of rock after cooling to previous temperature and thawing are that uniaxial compression strength and Young's modulus decrease as temperature decreases. Uniaxial compression strength and Young's modulus in wet conditon decrease more than those in dry condition. Brazilian tension strength decreases as temperature decreases.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2004년도 제30회 국제세미나
• /
• pp.19-42
• /
• 2004

Sizing properties in paper are generally developed through the application of both internal and surface sizes. Rosin, wax, and synthetic sizes including ASA, AKD, and stearic anhydride are and have been used to provide wet-end sizing to paper. In many cases, the use of some of these sizes leads to runnability problems that are inherent in the wet-end operation. Variability in furnish, fines, broke, filler, water chemistry, conductivity, and pH control impacts the wet-end operation. Size press chemicals including starch and polymers such as styrene-acrylic, styrene-maleic, and styrene acrylate emulsions are used in conjunction with internal sizes to improve the paper surface for printing and strength properties, porosity, and opacity improvement. This paper will discuss results from a new, proprietary formulation and process that allows application of sizing chemistry more totally at the size press with reduced emphasis on wet end sizing. Runnability issues are thus minimized at the wet-end, chemical usage is more efficient, and significant cost savings can be realized. Case histories will be presented illustrating the advantages of this new application in commercial trials.

• 펄프종이기술
• /
• 제37권4호통권112호
• /
• pp.8-17
• /
• 2005

WCT (Wet compaction test) is a new fiber evaluation method developed recently by Seo and its test results can be used as a predictor for pulp quality and its paper property Bleached chemical pulps (SwBKP, HwBKP), recycled pulp (OCC), and mechanical pulp (BCTMP) were used for the furnishes to be tested by WCT We compared the WCT results to conventional fiber evaluation tests such as WRV (Water Retention Value), free ness, and fiber length in this study, and found that WCT always gave better regression coefficients in relation to pulp quality (drainage), and paper properties (density, tensile, tear, and burst strength). WCT may be used on-line in papermachine.