• Journal of the Korean Wood Science and Technology
• /
• v.35 no.3
• /
• pp.36-44
• /
• 2007

The purpose of this study was to investigate thermal stability, reactivity, and bonding strength of existing epoxy resin mixed with the epoxidized soybean oil (ESBO) in order to use soybean oil economically. In the dry shear test, the marked strengths showed $30.5kgf/cm^2$ at the ratio of ESBO to epoxy resin 9 : 1 and $6.2kgf/cm^2$ at the ratio 8 : 2. The bonding strengths of the others, except mixing ratios 2 : 8 and 1 : 9, exceeded the requirement of Korean plywood standard of $7.0kgf/cm^2$. In the wet shear test, the result was $5.8kgf/cm^2$ at the ratio 9 : 1. There were no thickness swelling and moisture absorption in the water resistance of the film. The value of activation energy, Tg (${\Delta}E$), by DSC analysis showed between $110^{\circ}C$ and $120^{\circ}C$ through all ratios. Epoxy in the epoxy resin fully reacted with the hardener (TETA), but it is difficult to decide that epoxys in the ESBO were reacted directly with the hardener from FT-IR analysis. As the mixing ratio of ESBO increased, the thermal stabilities dropped from TGA analysis. From the comprehensive view on the results of above experiments, it could be confirmed through experiments that the ESBO in the mixed adhesive of epoxy resin/ESBO played a role as an extending agent level of epoxy adhesive, and we were able to know that in order to utilize ESBO as an adhesive, a study should be performed on the condition of hardening, inducible of the hardening reaction.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.20 no.1
• /
• pp.49-59
• /
• 1984

Optimizing investigation of characteristics of underwater welding by a gravity type arc welding process was experimentally carried out by using six types of domestic coated welding electrodes for welding of domestic marine structural steel plates (KR Grade A-1, SWS41A, SWS41B,) in order to develop the underwater welding techniques in practical use. Main results obtained are summarized as follows: 1. The absorption speed of the coating of domestic coated lime titania type welding-electrode became constant at about 60 minutes in water and it was about 0.18%/min during initial 8 minutes of absorption time. 2. Thus, the immediate welding electrode could be used in underwater welding for such a short time in comparison with the joint strength of in-atmosphere-and on-water-welding by dry-, wet-or immediate-welding-electrode. 3. By bead appearance and X-ray inspection, ilmenite, limetitania and high titanium oxide types of electrodes were found better for underwater-welding of 10 mm KR Grade A-1 steel plates, while proper welding angle, current and electrode diameter were 6$0^{\circ}C$, above 160A and 4mm respectively under 28cm/min of welding speed. 4. The weld metal tensile strength or proof stress of underwater-welded-joints has a quadratic relationship with the heat input, and the optimal heat input zone is about 13 to 15KJ/cm for 10mm SWS41A steel plates, resulting from consideration upon both joint efficiency of above-100% and recovery of impact strength and strain. Meanwhile, the optimal heat input zone resulting from tension-tension fatigue limit above the base metal's of SWS41A plates is 16 to 19KJ/cm. Reliability of all the empirical equations reveals 95% confidence level. 6. The microstructure of the underwater welds of SES41A welded in such a zone has no weld defects such as hydrogen brittleness with supreme high hardness, since the HAZ-bond boundary area adjacent to both surface and base metal has only Hv400 max with the microstructure of fine martensite, bainite, pearlite and small amount of ferrite.

• The Journal of Korean Academy of Prosthodontics
• /
• v.19 no.1
• /
• pp.17-27
• /
• 1981

This study was conducted to determine the chemical composition and the mechanical properties of four commercially available low gold-based crown and bridge alloy produced in Korea. Four dental casting gold-silver-palladium alloys, i.e., A, B, C and D (code of alloys) were selected for the evaluation of chemical composition, ultimate tensile strength, elongation. values and Vickers hardness. The chemical composition of test specimens was analyzed by both emission spectrography and wet gravitation method with a 1.5gm of low gold ingot. The tensile properties and Vickers hardness was determined with cast specimens treated in following three conditions; as-cast, softening heat treatment and hardening heat treatment. The tensile testing bars were cast in accordance with the model designed by Gettleman and Harrison (1969) which was modified from the A. D. A. Specification No. 14 for dental chromium-cobalt casting alloy. Nine tensile test specimens were made from a split silicone mold for each of the test alloys to the size of 2.5mm in diameter and a gauge length of 10mm. All four alloys were handled in accordance with conventional methods used in Type III gold alloys. Ultimate tensile strength and elongation were measured on an Instron Universal Tensile Testing Machine (Model 1125, Japan) operated at a crosshead rate of 0.1cm/min. Elongation values were measured using Digital Measuring Microscope (MS-152, FUSOH, Japan). Vickers hardness was determined with a Vickers Hardness Tester (Model VKH-l, Japan) at a 1.0kg load on a mounted tensile test specimen. The following results were obtained from this study; 1. All tested alloys were composed of Au, Ag, Pd, Cu, Zn and Fe in common. The composition rate of gold for all four alloys was found in the range of $42{\sim}47$ weight % as shown below. Alloy A; Au 45%, Ag 40.2%, Pd 5.76%, others 9.04%. Alloy B; Au 47.1%, Ag 29.03%, Pd 6.98%, others 16.92%. Alloy C; Au 45%, .Ag 26.9%, Pd 6.83%, others 21.07%. Alloy D; Au 41.8%, Ag 34.4%, Pd 6.95%, others 16.85%. 3. The ultimate tensile strength of the four alloys was in the range of $31{\sim}82kg/mm^2$. The test results were shown in the below order from the highest value; As-cast condition; D, B, C, A. Softening heat treament; B, C, D, A. Hardening heat treatment; D, B, C, A. 4. The test :results of the elongation rate for each alloy were in the range of $0.5{\sim}18%$. The test results were shown in the below order from the highest value; As-cast condition; A, D, B, C. Softening heat treatment; A, C, D, B. Hardening heat treatment; C, D, B, A. 5. Vickers hardness for each of the four alloys was in the range of $120{\sim}230$. The test results were shown in the below order from the highest value; As-cast condition; C, B, D, A Softening heat treatment; D, B, C, A. Hardening heat treatment; D, A, C, B. 6. There were no differences in the physical properties between as-cast condition and softening heat treatment.

• Korean Journal of Agricultural Science
• /
• v.13 no.1
• /
• pp.113-122
• /
• 1986

In order to promote mechanization of corn harvesting in Korea, this study was conducted to find out the effect of moisture content on compressive properties such as force, deformation, energy and modulus of stiffness to the bioyield and the rupture point for Korean corn kernel. In this study, the loading positions of corn were flat, edge, longitude and the moisture contents were about 13, 17, 21, 25% in wet basis. The compression test was carreied out with flat plate by use of dynamic straingage for three varieties of Korean corn under quasi-static force when the loading rate was 1.125mm/min. The results of this study are summarized as follows; 1. When the moisture content of corn ranged from 12.5 to 24.5 percent, at flat position, the bioyied force was in the range of 13.63-26.73 kg and the maximum compressive strength was in the range of 21.55-47.65kg. Their values were reached minimum at about 17% and maximum at about 21% moisture content. The bioyield force was in the range of 13.58-6.70kg at edge position and the maximum compressive strength which was 16.42 to 7.82kg at edge position was lower than that which was 18.55-9.05kg at longitudinal position. 2. Deformation of corn varied from 0.43 to 1.37 mm at bioyield point and from 0.70 to 2.66mm at rupture point between 12.5 to 24.5% moisture content. As the moisture content increased, deformation was increased. 3. The moduli of resilience and toughness of corn ranged from 2.60 to 8.57kg. mm and from 6.41 to 34.36kg. mm when the moisture content ranged from 12.5 to 24.5 percent, respectively. As the moisture content increased, the modulus of toughness was increased at edge position and decreased at longitudinal position. And their values were equal each other at 22-23% moisture content. 4. The modulus of stiffness was decreased with increase in the moisture content. Its values ranged from 32.07 to 5.86 kg/mm at edge position and from 42.12 to 18.68kg/mm at flat position, respectively. Also, the values of Suweon 19 were higher than those of Buyeo. 5. It was considered that the compressive properties of corn at flat position were more important on the design data for corn harvesting and processing machinery than those of edge or longitudinal position. Also, grinding energy would be minimized when a corn was processed between about 12.5 to 17% moisture content and corn damage would be reduced when a corn was handled between about 19 to 24% moisture content in wet basis.

• Journal of the Korea Concrete Institute
• /
• v.18 no.1 s.91
• /
• pp.125-132
• /
• 2006

Recently, surface finishing and protection materials were developed to restore performance of the deteriorated concrete and inhibiting corrosion of the reinforcing-bar. For this purpose, surface protection agent as well as coatings are used. Coatings have the advantage of low Permeability of $CO_2,\;SO_2$ and water. However, for coatings such as epoxy, urethane and acryl, long-term adhesive strength is reduced and the formed membrane of those is blistered by various causes. Also when organic coatings are applied to the wet surface of concrete, those have a problem with adhesion. On the other hand, surface protection agent penetrates into pore structure in concrete through capillary and cm make a dense micro structure in concrete as a result of filling effect. Furthermore, the chemical reaction between silicate from surface protection agent and cement hydrates can also make a additional hydration product which is ideally compatible with concrete body. The aim of this study is to examine the effect of penetrative surface protection agent(SPA) by evaluating several concrete durability characteristics. The results show that the concrete penetrated surface protection agent exhibited higher durability characteristics for instance, carbonation velocity coefficient, resistance to chemical attack and chloride ion penetration than the plain concrete. These results due to formation of a discontinuous macro-pore system which inhibits deterioration factors of concrete by changed the pore structure(porosity and pore size distributions) of the concrete penetrated surface protection agent.

• Journal of the Korean Ceramic Society
• /
• v.39 no.11
• /
• pp.1042-1047
• /
• 2002

The sedimentation characteristics of ceramic fiber were analyzed when viscosity of the slurry for ceramic paper formation was varied and zeta potential change and degree of dispersion with pH were studied as well. The proper viscosity of the slurry for dispersion of fibers was between 28 and 31 cps. Zeta potential of the slurry was sensitively changed with pH adjustment and showed maximum value of -35~-36 mV at ph 7.5~9.5, which indicated better dispersion of ceramic fiber as zeta potential of the slurry was increased. The sedimentation rate of ceramic fiber in a slurry was reported minimum at the maximum zeta potential. Water content of the casted paper should be lower than 83% after vacuum dehydration for retention of binder and lower than 62% after press rolling for wet paper handling. The obtained ceramic paper had tensile strength and basis weight, $102 kgf/cm^2$ and $98 g/m^2$, respectively.

• Journal of Conservation Science
• /
• v.26 no.3
• /
• pp.335-340
• /
• 2010

Urethane resin applicable for the first transcription of historical site and transcription of soil layer were synthesized in order to replace the imported urethane resin, NS-10. Comparing to the NS-10, the urethane polymers showed similar penetration to wet soil and formed a stable layer of polyurethane during progress working the peeling off the polyurethane pre-product from epoxy surface of final product. The urethane resins used for the first transcription of historical site improved tensile strength, which is consistent with that of NS-10. In addition the urethane resin for transcription of soil layer was supplied with hardness that have a also same strong point as like NS-10. This property is advantage due to simplifying the transcription work of soil layer in backward. When we tested to the real ground soil as well as experimentation compressed soil with use these synthesis urethane resin, we ca get the satisfying result in penetration property and stability and these properties evaluated the resins as an advanced product serving better convenience for worker.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.33 no.12
• /
• pp.1873-1882
• /
• 2009

Hospital patient clothing material was treated with a mixture of chitosan in order to enhance functionality, such as the durability and dimensional stability of the cotton fabric used. Chitosan is a natural polymer with excellent biocompatibility, however there is a deteriorating adherence efficiency. The addition of a nanosilver colloidal solution in accordance with a prescribed ratio can further increase the performance of chitosan. Changes in the structural characteristics and physical properties of the chitosan/nanosilver treated fabric were observed in a comparison with fabric treated only with chitosan. The add-on ratio increased when the mixing ratio of nanosilver colloidal solution was higher; however, the crystalline structure of the treated fabric remains similar. In the case of CH3/NS1 treated fabric (where the mixing ratio of chitosan and nanosilver solution was 3:1) the K/S value, whiteness index, wet tensile strength, and wrinkle recovery angle were superior. The dimension stability, pilling resistance, and abrasion resistance of the fabric treated with a mixed solution increased in comparison to the fabric treated only with chitosan. The chitosan/nanosilver treated cotton fabric used for patient clothing material has excellent physical properties.

• Journal of Applied Biological Chemistry
• /
• v.58 no.2
• /
• pp.145-151
• /
• 2015

Corn fiber protein (CFP) was extracted from corn wet-milling by-product, corn fiber. CFP films containing various plasticizers and cross-linking agents were prepared and their mechanical properties were determined. Among the plasticizers and cross-linking agents used in this study, the CFP film containing 2 g fructose and 0.03% cinnamaldehyde had the most appropriate physical property. In addition, the CFP films containing green tea extract (GTE) were prepared by incorporating different amounts (0, 0.5, 1.0, 1.5%) of GTE into the film-forming solution. Tensile strength, film solubility, and opacity of the CFP films increased with the addition of GTE, whereas elongation and water vapor permeability of the CFP/GTE films decreased compared to those of the control. The antioxidant activity of the CFP/GTE film was determined in terms of 2,2-diphenyl-1-picrylhydrazyl radical scavenging activity. As a result, antioxidant activity of the films increased with increasing GTE concentration. Furthermore, antimicrobial activity against Escherichia coli O157:H7, Listeria monocytogenes, and Staphylococcus aureus increased with increasing GTE concentration. These results indicate that the incorporation of GTE could enhance antioxidant and antimicrobial activities of the CFP films.

• Korean Journal of Environmental Agriculture
• /
• v.25 no.1
• /
• pp.1-6
• /
• 2006

This study was carried out to investigate yearly change in the precipitation component and the source strength to acid precipitation at Iksan area from 1997 to 2003. The average ratio of acid precipitation was 70.0% in 1997, 56.3% in 1998 and 36.4% in 2003. On the other hand, it ranged from 6.9 to 19.2% when precipitation was less from 1999 to 2002. The average annual wet depositions of major ionic component in precipitation were calculated by multiplying equivalent concentration by precipitation. The order of major anion component in precipitation was ${SO_4}^{2-}>Cl^->{NO_3}^-$. On the other hand, the concentration of cation component were ${Ca_2}^+>Na^+>{NH_4}^+>{Mg_2}^+>K^+$ in order. The negative correlation was shown between pH and ionic component in precipitation except for ${Ca_2}^+\;and\;Na^+$. The correlation coefficient between pH and ${SO_4}^{2-}$ was highly significant as -0.508, which suggests that ${SO_4}^{2-}$ played important role in increasing the acidity of precipitation. Also the anions such as ${SO_4}^{2-}\;and\;{NO_3}^-$ were highly significant with cations such as ${Ca_2}^+,\;{Mg_2}^+,\;K^+,\;{NH_4}^+\;and\;Na^+$. As a result though pH was enable to use the acidity index of precipitation in somewhere, evaluating only pH in precipitation was insufficient as the index to establish corresponding strategy for acid rain.