• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2005년도 춘계 학술발표회 논문집
• /
• pp.1412-1419
• /
• 2005

Preventing the infiltration of rainwater into the landfill site is the main purpose of the final cover in landfill sites. Compacted clay layer or geomembrain have been used as a conventional landfill final cover. But they have several disadvantages when damages might occur due to puncturing, differential settlement and desiccation or freeze and thaw. For this reason, as an alternative method SRSL(Self Recovering Sustainable Liner) has been developed. Adopting the precipitation reaction of two chemical material, by forming precipitates that fill the pores, and lower the overall permeability of the liner. The advantage of this method is that when fracture of the liner occurs the remaining reactants of the two layers form precipitates that fill the fracture and recover the low permeability of the liner. In this study, the recovering ability of the SRSL with a crack due to the seasonal variation or differential settlements was investigated by permeability tests. And in order to estimate the durability of the SRSL after freeze/thaw and desiccation, uniaxial compression strength tests were performed.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.830-833
• /
• 2003

This paper describes the fabrication and characteristics of 3C-SiCOI sotctures by SDB and etch-back technology for high-temperature MEMS applications. In this work, insulator layers were formed on a heteroepitaxial 3C-SiC film grown on a Si(001) wafer by thermal wet oxidation and PECVD process, successively. The pre-bonding of two polished PECVD oxide layers made the surface activation in HF and bonded under applied pressure. The wafer bonding characteristics were evaluated by the effect of HF concentration used in the surface treatment on the roughness of the oxide and pre-bonding strength. Hydrophilic character of the oxidized 3C-SiC film surface was investigated by ATR-FTIR. The strength of the bond was measured by tensile strengthmeter. The bonded interface was also analyzed by SEM. The properties of fabricated 3C-SiCOI structures using etch-back technology in TMAH solution were analyzed by XRD and SEM. These results indicate that the 3C-SiCOI structure will offers significant advantages in the high-temperature MEMS applications.

• 한국세라믹학회지
• /
• 제26권1호
• /
• pp.123-131
• /
• 1989

Hydroxyapatite powders were syntehsized by the reaction of Ca(NO3)2.4H2O and (NH4)2HPO4 in aqueous solution. The effect of the Ca/P mole ratio in the starting solution on the sintering of the powders and its microstructure was studied. When the Ca/P mole ratio in the starting solution was 1.69, the relative density of the sintered bodies was more than 95%. The sinterability was decreased as the Ca/P mole ratio in the starting solution was increased (Ca/P mole ratio >1.67). Hydroxyapatite sintered bodies obtained from the Ca/P mole ratio=1.69 had very excellent bending strength. The best bending strength was obtained at 110$0^{\circ}C$ and its value was 1220kg/$\textrm{cm}^2$. The average grain size was 0.277${\mu}{\textrm}{m}$. Most of sintered bodies were almost shown 100% hydroxyapatite phase. However, in case of the Ca/P mole ratio=1.64 hydroxyapatite was decomposed to $\alpha$-whitlockite above 120$0^{\circ}C$.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 1999년도 추계학술발표대회 논문집
• /
• pp.28-31
• /
• 1999

Carbon fiber/epoxy composites using electrodeposited monomeric and polymeric coupling agents were compared with the dipping and the untreated cases. Treating conditions such as time, concentration and temperature were optimized. Four-fibers embedded micro-composites were prepared for fragmentation test. Interfacial properties of four-fiber composites with different surface treatments were investigated with simultaneous acoustic emission (AE) monitoring. The microfailure mechanisms occurring from fiber break, matrix and interlayer crackings were examined by AE parameters and an optical microscope. It was found that interfacial shear strength (IFSS) of electrodeposited carbon fibers was much higher than the other cases under dry and wet conditions. Well separated and different-shaped AE groups occurs for the untreated and ED treated case, respectively.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.593-598
• /
• 2003

Ceramic plates containing many micro-holes are used in diverse applications such as MCP (Microchannel Plate). catalytic converters, filters, electrical insulators in integrated circuits, and so on. One of the efficient methods for machining many holes in ceramic plates is wet drilling of ceramic green bodies followed by sintering them. Since the strength of ceramic green bodies is much lower than the strength of sintered ceramic plate, ceramic green bodies can be drilled with high feed rate. The axial force during micro-drilling of ceramic green bodies increases rapidly at high feed rate, which induces the crack in workpiece. Therefore, the tool lift of micro-drill with respect to feed rate may be determined by the predicting increase of axial force. In this work, the axial force during micro-drilling was calculated using the chip flow model on the micro-drill tip. from which the tool life of diamond abrasive micro-drill during micro-drilling of ceramic green bodies was calculated.

• Geomechanics and Engineering
• /
• 제19권5호
• /
• pp.435-445
• /
• 2019

A series of element tests with different drainage conditions and strain rates were performed on compacted unsaturated non-plastic silt in unconfined conditions. Soil samples were compacted at water contents from dry to wet of optimum with the degree of saturation varying from 24 to 59.5% while maintaining the degree of compaction at 80%. The tests performed were shear infiltration tests in which specimens had constant net confining pressure, pore air pressure was kept drained and constant, just before the shear process pore water pressure was increased (and kept constant afterwards) to decrease matric suction and to start water infiltration. In constant water content tests, specimens had constant net confining pressure, pore air pressure was kept drained and constant whereas pore water pressure was kept undrained. As a result, the matric suction varied with increase in axial strain throughout the shearing process. In both cases, maximum shear strength was obtained for specimens prepared on dry side of optimum moisture content. Moreover, the gradient of stress path was not affected under different strain rates whereas the intercept of failure was changed due to the drainage conditions implied in this study.

• 한국의류학회지
• /
• 제29권9_10호
• /
• pp.1274-1284
• /
• 2005

Effect of fixation methods and relaxation treatment on the dimensional stability and physical properties of MDPPA/HMM treated cotton knitted fabrics were studied. Combination of four different fixation methods - relaxation, swelling agent treatment, pad dry cure fixation, and wet fixation - were applied to flame retardant finish of 4 kinds of cotton knitted fabric with MDPPA/HMM. Then these fabrics were washed 10 times. As a result, In swelling treatment on 10G showed relatively higher value of length shrinkage than 14G. Length and width shrinkage were increased by initial washing treatment and no further change was shown after 6 washing cycles. After 10 washing cycles, length and width shrinkage decreased. The KES standardized basic value of B/W, 2HB/W and bursting strength of interlock were relatively larger than those of single jersey. The values of B/W and 2HB/W of cotton knitted fabrics were increased by relaxation and washing treatment but were decreased by swelling treatment. In addition, the bursting strength of the cotton knitted fabrics was decreased after fusing, washing and relaxation treatment.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1301-1302
• /
• 2008

In this study, the fracture strength for fracture mechanism porous calcium phosphate made from sintered with ${\beta}$-tricalcium phosphate obtained by wet precipitation procedure is analyzed using finite element method and experiment measurement. First, three $3{\times}3{\times}3mm^3$ and $5{\times}5{\times}5mm^3$ specimens are prepared and tomographic images of one $5{\times}5{\times}5mm^3$ specimen are obtained by micro focus X-ray CT. The compression tests using the specimens are carried out to measure the elastic modulus and fracture strength to analyze the fracture mechanism of porous calcium phosphate specimen. The tomographic images are reconstructed by 3D reconstruction program. The finite elements are directly built up in the reconstructed specimen. The numerical simulation for the compression tests is performed using the element. The mechanism of calcium phosphate of simulation are obtained by the compression tests using there cylindric specimen of height 19.5 mm and diameter 10 mm. From the results, the applicability of porous calcium phosphate is evaluated to care fracture and vacant bone of a patient as the reinforcement material.

• 한국의류학회지
• /
• 제37권3호
• /
• pp.348-356
• /
• 2013

Denim washing is processed with different washing techniques such as stone washing, chemical washing, sand washing, and bio washing. Cellulase bio washing can meet environmental regulations that enhance and rectify problems associated with traditional decolorization techniques; however, stone washing needs to be added to the processing because it produces a low decolorization effect. There is also the problem of additional strength reduction. To prevent these problems, a new enzyme for bio washing is required. This study examines the optimum laccase treatment conditions on denim and evaluated the characteristics of laccase-treated denims to establish a database of eco-friendly new decolorization process on denim using a new laccase enzyme. The results show that the optimum conditions of laccase on denim are a pH of 4.0, $30^{\circ}C$, 7% (o.w.f.), and 6 hours in 10 mM of buffer concentration. UV absorbance and HPLC identified isatin coexist with anthranilic acid in solution after laccase treatment on denim. Results of the surface color, the surface morphology and the tensile strength indicate that laccase treatment shows an excellent decolorization effect without fiber damage. The wet cleaning fastness and the perspiration fastness also improved.

• 한국염색가공학회지
• /
• 제11권1호
• /
• pp.34-41
• /
• 1999

To examine the increase of paper strength by solvent-bonding using N-methylmorpholine N-oxide (NMMO), a paper was treated with aqueous solutions of NMMO, concentrated at $90^\circ{C}$ for selected periods of time, and pressed for 5 seconds followed by washing and drying. The effect of the increasing NMMO concentration on bonding state and some important properties of samples were mainly investigated. With increasing concentration of NMMO, the degree of bonding between fibers was increased, the fiber cross-sectional shape was changed from 'thin ribbonlike' to 'round rodlike' by swelling with solvent, and the longitudinal waves (crimp) were introduced to fibers, hence the shrinkage, weight per unit area, and thickness of paper were increased. Consequently, the tensile strength and elongation, under standard and wet conditions, and the stiffness were increased, and the water absorption was decreased generally with increasing concentration of NMMO. The moisture regain of treated samples was lower than that of the untreated sample, because of the reduction of space between fibers. But the moisture regain was increased a little with increasing concentration of NMMO due to the fiber swelling with NMMO followed by structural relaxation.