• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.33 no.1
• /
• pp.56-59
• /
• 2020

Porcelain insulators are typically exposed to surface discharge and lightning impulse in service. This study investigates the insulation characteristics of the external and internal discharges of a porcelain insulator with respect to its flashover for a 154 kV transmission line. The experiments are also conducted using a wet flashover test and an impulse test based on the external discharge and the internal penetration, to classify the flashover voltage-time curve of the porcelain insulator. When an impulse with a strength of 2,500 kV/㎲ was applied three times to 6.5 mm ceramic samples, electrical penetration of approximately 70% occurred. The impulse experiment confirmed that the electrical penetration inside the porcelain insulator coincided with the area where the electric field was concentrated. The wet flashover voltage test revealed that the flashover threshold voltage increases by approximately 7% after cleaning of the surface.

• Korean journal of food and cookery science
• /
• v.25 no.2
• /
• pp.199-205
• /
• 2009

Wet noodles with different percentages of Curcuma Ionga L. powder(CLP) as an additive were generated and their cooking characteristics were evaluated. Wheat flour with 8% CLP had the highest water binding capacity and breakdown, while setback was reversed. Cooked noodle characteristics, weight, volume and tensile strength decreased as CLP content of wheat flour increased, but turbidity of the soup was reversed. L value of wet noodles was higher than cooked noodles, while b value, and texture of wet noodles were lower than cooked noodles. Hunter color value and texture measurements demonstrated decreasing L value, springiness and cohesiveness but increasing b value, hardness, gumminess and chewiness with increasing CLP content. In sensory evaluations, noodles made with 4% CLP were most highly preferred, while noodles made with 2% and 8% CLP were less preferred than CLP-free prepared noodles.

• Polymer(Korea)
• /
• v.34 no.3
• /
• pp.226-236
• /
• 2010

UV irradiated acrylic pressure sensitive adhesives(PSAs) are prepared to be used for thermal pad in plasma display panel(PDP). The effect of the chemical structure of side-chain in comonomer and of crosslinking agent on wet-out property of acrylic PSAs in wide temperature range were investigated. The correlationship between viscoelastic behavior and adhesion properties, such as tack and peel strength, was also studied. The experimental results supported that wet-out and adhesion properties of acrylic PSAs were enhanced inversely proportional to side-chain length of comonomer in wide temperature range. The peel energy clearly increased in acrylic PSAs prepared by using di(ethylene glycol) dimethylacrylate (DEGDMA) for crosslinking agent. The results might be due to the difference in the glass transition temperature and viscoelastic behavior of acrylic PSAs.

• International Journal of Highway Engineering
• /
• v.20 no.1
• /
• pp.77-85
• /
• 2018

PURPOSES : The purpose of this study was to develop an urgent road-repair system and perform a field applicability test, as well as discover the optimum mix design for machine applications compared to the optimum mix design for lab applications. METHODS : According to reviews of the patent and developed equipment, self-propelled and mix-in-place equipment types are suitable for urgent pavement repair, e.g., potholes and cracks. The machine-application mix design was revised based on the optimum lab-test mix design, and the field application of a spray-injection system was performed on the job site. The mixture from the machine application and lab application was subjected to a wet-track abrasion test and a wheel-tracking test to calibrate the machine application. RESULTS and CONCLUSIONS : This study showed that the binder content could differ for the lab application and the machine application in the same setting. Based on the wet-track abrasion test result, the binder contents of the machine application exceeded the binder contents of the lab application by 1-1.5% on the same setting value. Moreover, the maximum dynamic stability value for the machine application showed 1% lower binder contents than the maximum lab-application value. Collectively, the results of the two different tests showed that the different sizes and operating methods of the machine and lab applications could affect the mix designs. Further studies will be performed to verify the bonding strength and monitor the field application.

• Polymer(Korea)
• /
• v.26 no.1
• /
• pp.45-52
• /
• 2002

The separator made from the blends of high density polyethylene (HDPE) and ultrahigh molecular weight polyethylene (UHMWPE) was prepared by wet processing to use as Li-ion secondary battery. We investigated effects of the blending of the polymers and the film extension on the mechanical properties of the separator. The mechanical strength of separator increased with increasing molecular weights and contents of UHMWPE, for instance about $1000 kg/\textrm{cm}^2$ with the five times extended film of 6 wt% UHMWPE. The pores of the separator were very uniform with the size of 0.1~$0.12\mu\textrm{m}$. The shut-down characteristic quickly increased at around $130^{\circ}C$ and the fusion temperature was $160^{\circ}C$, so it could be applied to the lithium ion secondary battery.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.50 no.3
• /
• pp.274-283
• /
• 2014

Swelling of the heat-treated netting for gillnet was estimated through the netting height in square acrylic tank. Experimental Nylon netting and PBSAT netting were heat-treated by using the high-degree vacuum method in hot water after net making. Heat-treatment temperatures were conducted with Nylon netting $105^{\circ}C$ and PBSAT netting $62^{\circ}C$, $65^{\circ}C$, $66^{\circ}C$, $67^{\circ}C$. The swelling measurement method of a netting using the square tank was capable of the reduction measurement errors comparing with measurement methods of a mesh inner angle and the shortening rate of a mesh size. In addition, this method was available to comparison evaluation for each netting more easily. Wet type heat-treatment apparatus with high-degree vacuum was shown higher $7{\sim}8^{\circ}C$ inner side temperature than a setting temperature. The tensile strength and elongation of Nylon netting and PBSAT netting were shown higher wet condition than dry condition. The tensile strengths of PBSAT monofilaments in dry and wet condition were sharply decreased at heat-treatment temp. $75^{\circ}C$ than heat-treatment temp. $74^{\circ}C$.

• Journal of Welding and Joining
• /
• v.30 no.3
• /
• pp.26-31
• /
• 2012

Three-dimensional integrated circuit (3D IC) technology has become increasingly important due to the demand for high system performance and functionality. We have evaluated the effect of Buffered oxide etch (BOE) on the interfacial bonding strength of Cu-Cu pattern direct bonding. X-ray photoelectron spectroscopy (XPS) analysis of Cu surface revealed that Cu surface oxide layer was partially removed by BOE 2min. Two 8-inch Cu pattern wafers were bonded at $400^{\circ}C$ via the thermo-compression method. The interfacial adhesion energy of Cu-Cu bonding was quantitatively measured by the four-point bending method. After BOE 2min wet etching, the measured interfacial adhesion energies of pattern density for 0.06, 0.09, and 0.23 were $4.52J/m^2$, $5.06J/m^2$ and $3.42J/m^2$, respectively, which were lower than $5J/m^2$. Therefore, the effective removal of Cu surface oxide is critical to have reliable bonding quality of Cu pattern direct bonds.

• Composites Research
• /
• v.20 no.5
• /
• pp.49-55
• /
• 2007

Nanocomposite blade for dicing semiconductor wafer is investigated for micro/nano-device and micro/nano-fabrication. While metal blade has been used for dicing of silicon wafer, polymer composite blades are used for machining of quartz wafer in semiconductor and cellular phone industry in these days. Organic-inorganic material selection is important to provide the blade with machinability, electrical conductivity, strength, ductility and wear resistance. Maintaining constant thickness with micro-dimension during shaping is one of the important technologies fer machining micro/nano fabrication. In this study the fabrication of blade by wet processing of mixing conducting nano ceramic powder, abrasive powder phenol resin and polyimide has been investigated using an experimental approach in which the thickness differential as the primary design criterion. The effect of drying conduction and post pressure are investigated. As a result wet processing techniques reveal that reliable results are achievable with improved dimension tolerance.

• Asian-Australasian Journal of Animal Sciences
• /
• v.29 no.6
• /
• pp.845-854
• /
• 2016

Characteristics and properties of gelatin from goat skin pretreated with NaOH solutions (0.50 and 0.75 M) for various times (1 to 4 days) were investigated. All gelatins contained ${\alpha}$-chains as the predominant component, followed by ${\beta}$-chain. Gelling and melting temperatures of those gelatins were $23.02^{\circ}C$ to $24.16^{\circ}C$ and $33.07^{\circ}C$ to $34.51^{\circ}C$, respectively. Gel strength of gelatins increased as NaOH concentration and pretreatment time increased (p<0.05). Pretreatment for a longer time yielded gelatin with a decrease in $L^*$-value but an increase in $b^*$-value. Pretreatment of goat skin using 0.75 M NaOH for 2 days rendered the highest yield (15.95%, wet weight basis) as well as high gel strength (222.42 g), which was higher than bovine gelatin (199.15 g). Gelatin obtained had the imino acid content of 226 residues/1,000 residues and the gelatin gel had a fine and ordered structure. Therefore, goat skin gelatin could be used as a potential replacer of commercial gelatin.

• International Journal of Advanced Culture Technology
• /
• v.6 no.3
• /
• pp.163-172
• /
• 2018

The power train of hydro-mechanical continuously variable transmission(HMCVT) for the middle class forklift makes use of an hydro-static unit, hydraulic multi-wet disc brake & clutches and complex helical & planetary gears. The complex helical & planetary gears are a very important part of the transmission because of strength problems. The helical & planetary gears belong to the very important part of the HMCVT's power train where strength problems are the main concerns including the gear bending stress, the gear compressive stress and scoring failures. The present study, calculates specifications of the complex helical & planetary gear train and analyzes the gear bending and compressive stresses of the gears. It is necessary to analyze gear bending and compressive stresses confidently for an optimal design of the complex helical & planetary gears in respect of cost and reliability. This paper not only analyzes actual gear bending and compressive stresses of complex helical & planetary gears using Lewes & Hertz equation, but also verifies the calculated specifications of the complex helical & planetary gears by evaluating the results with the data of allowable bending and compressive stress from the Stress - No. of cycles curves of gears. In addition, this paper explains actual gear scoring and evaluates the possibility of scoring failure of complex helical & planetary gear train of hydro-mechanical continuously variable transmission for the forklift.