• Elastomers and Composites
• /
• v.59 no.1
• /
• pp.17-21
• /
• 2024

Solution styrene-butadiene rubber (S-SBR) is used to improve the wet grip and rolling resistance properties of tire treads. As blending of SBRs can improve the physical properties of tire treads, we investigated the effects of SBR type and blending ratio on the physical properties. Twelve SBR/SBR biblend composites were prepared using four SBRs with different microstructures. The glass transition temperature (T_g), tanδ at 0℃ (wet grip predictor), and tanδ at 60℃ (rolling resistance predictor) were obtained from dynamic mechanical analysis, and were compared to the expected values obtained from the results of single SBR samples. Most of the SBR/SBR biblend composites exhibited crosslink densities lower than the expected values. The tanδ values at 0℃ and 60℃ of the SBR/SBR blend composites deviated from the expected values, with many of the deviations being disadvantageous. Of the twelve composites, six samples had higher 0℃ tanδ values than the corresponding expected values, and four exhibited superior wet grip properties to those of the SBR single samples. In addition, two of the twelve samples exhibited improved rolling resistance properties as compared with the single SBR samples. Finally, four samples exhibited lower T_g values than expected, and the T_g of one composite was lower than those of the single SBR samples.

• Elastomers and Composites
• /
• v.59 no.1
• /
• pp.8-16
• /
• 2024

As regulations on greenhouse gas emission have strengthened globally, the demand for improved fuel efficiency in automobiles continues to rise. In response, the tire industry is actively conducting research to improve fuel efficiency by enhancing tire performance. In this study, silica-filled epoxidized natural rubber (ENR)/butadiene rubber (BR) blend compounds were manufactured according to ENR types and silica contents, and their physical properties and vulcanizate structure were evaluated. ENR-50, which has a higher epoxide content than ENR-25, exhibited stronger filler-rubber interaction, resulting in superior abrasion resistance. In addition, because of its high glass transition temperature (T_g), the wet grip performance of ENR-50 improved, even though the rolling resistance increased. Increasing the amount of silica had little effect on the abrasion resistance due to the increase in filler-rubber interaction and decrease in toughness. In addition, ENR-50 exhibited better wet grip performance; however, the rolling resistance increased. The results indicated that truck bus radial (TBR) tire tread compounds can be designed by applying ENR-50 to improve wear resistance and wet grip performance. In addition, by applying ENR-25 and reducing the silica contents improve fuel efficiency.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.10a
• /
• pp.265-267
• /
• 2013

Tire labeling is an important issue to reduce $CO_2$ and to secure the safety of tire/vehicle on wet road. A basic study on the effects of tire basic stiffness design on tire labeling performance has been done through experimental test. The pass-by noise is affected by tire structural design. The tire with lower side part stiffness and lower tread part stiffness has the lowest PBN level and the best wet grip. And the tire with higher tread part stiffness and higher side part stiffness has the better RR performance. Also it is observed that the trade-off between RR and wet grip exists for various tire stiffness design.

• Elastomers and Composites
• /
• v.50 no.3
• /
• pp.159-166
• /
• 2015

Silica which is used for reinforcing filler in tire industry is widely known as eco-friendly material exerting $CO_2$ reduction effect through decrease of rolling resistance and improvement of wet grip. Generally silica is classified as a highly polar filler because it contains a large number of silanol (Si-OH) group on its surface. And also silica gives a lower reinforcing effect than carbon black due to its poorer rubber-filler interaction. Therefore silica is treated with silane coupling agent or activator, then following the conventional rubber blend method, vulcanized sheets were prepared using a hot press, and cure characteristics, mechanical properties and abrasion resistance of the test specimens were investigated. It was found that with an increase in the silane coupling agent content the tensile strength, 300% modulus and abrasion resistance increased while Mooney viscosity decreased and crosslink density slightly increased with an increase of activator.

• Elastomers and Composites
• /
• v.49 no.3
• /
• pp.191-198
• /
• 2014

We synthesized thermoplastic polyurethane elastomer(TPU) with acid group and nano zinc oxide, and characterized their mechanical properties, thermal properties, contact angle and grip property. The effects of the zinc oxide content and size on the physical property of TPU were investigated. When the nano zinc oxide was introduced in TPU with acid group, it had excellent mechanical properties and grip by formation of hydrogen and ionic bonding. The wet slip of TPU with zinc oxide was increased continuously as ionization rate increased due to increase of hydrophilicity and ionic interaction, and mechanical properties were increased with increasing ionization rate up to 50%.

• Elastomers and Composites
• /
• v.54 no.4
• /
• pp.299-307
• /
• 2019

Rubber friction properties include adhesion friction characteristics of the interface, hysteresis friction characteristics originating from repeated rubber deformations, and cohesion friction characteristics due to wear and tear. Cohesion friction is generally sufficiently small (< 3%) that it can be ignored, whereas adhesion friction has a relatively large contribution of 15%, but has not been investigated thoroughly. Therefore, through an adhesion friction study, the adhesion mechanism was examined and the relationship between friction characteristics and adhesion friction on dry surfaces was derived. The wet grip characteristics of tread rubber are fully described by the hysteresis characteristics of tires, but friction characteristics on dry roads are difficult to determine without adhesion factors. The results presented herein demonstrate that the combination of hysteresis and adhesion properties in the tread rubber sufficiently explained the characteristics of the dry grip. Based on the results of this study, technologies will be developed to determine the key factors governing adhesion friction characteristics and improve dry tire braking performance.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.1
• /
• pp.214-221
• /
• 2007

This paper presents a myoelectric hand prosthesis(MHP) with two degree of freedom(2-DOF), which consists of a mechanical hand, a surface myoelectric sensor(SMES) for measuring myoelectric signal, a control system and a charging battery. The actuation for the 2-DOF hand functions such as grasping and wrist rotation was performed by two DC-motors, and controlled by myoelectric signal measured from the residual forearm muscle. The grip force of the MHP was automatically changed by a mechanical automatic speed reducer mounted on the hand. The skin interface of SMES was composed of the electrodes using the SUS440 metal in order to endure a wet condition due to the sweat. The sensor was embedded with a amplifier and a filter circuit for rejecting the offset voltage caused by power line noises. The control system was composed of the grip force sensor, the slip sensor, and the two controllers. The two controllers were made of a RISC-type microprocessor, and its software was executed on a real-time kernel. The control system used Force Sensing Resistors, FSR, as slip pick-ups at the fingertip of a thumb and the grip force information was obtained from a strain-gauge on the lever of the MHP. The experimental results were showed that the proposed control system is feasible for the MHP.

• Elastomers and Composites
• /
• v.48 no.4
• /
• pp.256-262
• /
• 2013

We synthesized thermoplastic polyurethane elastomer (TPU) with different contents of sulfuric acid group, and characterized their physical properties such as mechanical, thermal and grip properties. And the results were compared with carboxylic acid-introduced TPU. Wet slip, tensile strength and abrasion properties were increased by the introduction of acid group. Mechanical properties increased with increasing the acid content up to 0.3 wt%. However, wet slip was continually increased as the acid content increased due to increase of hydrophilicity of TPU.

• Journal of Adhesion and Interface
• /
• v.14 no.2
• /
• pp.68-74
• /
• 2013

We synthesized polyurethane elastomer containing acid groups. We measured the adhesion, grip, tensile strength and mechanical properties. Casting polyurethane elastomers were prepared with the contents of acid. The adhesive strength and the wet slip were increased. Also, the tensile strength and abrasion properties were increased. We measured the properties with different acid contents. Increasing the acid content, the mechanical properties were increased. But the mechanical properties were decreased above 0.20 wt% of acid content. The wet slip was increased and the contact angle was decreased as the acid content increased.

• Journal of Adhesion and Interface
• /
• v.16 no.2
• /
• pp.63-68
• /
• 2015

We synthesized thermoplastic polyurethane elastomer containing carboxylic acid group and TPV (thermoplastic vulcanizate). We measured the mechanical, grip, debris, contact angle and adhesion properties according to introducing acid group in elastomer structure. Mechanical and wet slip properties were improved because of the hydrogen bonding by introduction of acid group. Also adhesion strength was increased as increasing of surface polarity by carboxylic acid group. The debris property of TPV made from TPU containing carboxylic acid group was improved.