• Journal of the Korean Chemical Society
• /
• v.65 no.3
• /
• pp.197-202
• /
• 2021

In this study, activated clay treated with H₂SO₄ (20% by weight) and heat at 90 ℃ for 8 h for acid white soil was used as an adsorbent for the removal of PO₄^3--P in water. Prior to the adsorption experiment, the characteristics of activated clay was examined by X-ray Fluorescence Spectrometry (XRF) and BET surface area analyser. The adsorption of PO₄^3--P on activated clay was steeply increased within 0.25 h and reached equilibrium at 4 h. At 5 mg/L of low PO₄^3--P concentration, roughly 98% of adsorption efficiency was accomplished by activated clay. The adsorption data of PO₄^3--P were introduced to the adsorption isotherm and kinetic models. It was seen that both Freundlich and Langmuir isotherms were applied well to describe the adsorption behavior of PO₄^3--P on activated clay. For adsorption PO₄^3--P on activated clay, the Freundlich and Langmuir isotherm coefficients, K_F and Q, were found to be 8.3 and 20.0 mg/g, respectively. The pseudo-second-order kinetics model was more suitable for adsorption of PO₄^3--P in water/activated clay system owing to the higher correlation coefficient R² and the more proximity value of the experimental value q_e,exp and the calculated value q_e,cal than the pseudo-first-order kinetics model. The results of study indicate that activated clay could be used as an efficient adsorbent for the removal of PO₄³-P from water.

• Journal of Bio-Environment Control
• /
• v.31 no.4
• /
• pp.485-496
• /
• 2022

Modern agriculture is being transformed into smart agriculture to maximize production efficiency along with changes in the 4th industrial revolution. However, rural areas in Korea are facing challenges of aging, low fertility, and population outflow, making it difficult to transition to smart agriculture. Among ICT technologies, simulation allows users to observe or experience the results of their choices through imitation or reproduction of reality. The combination of the three-dimension (3D) model and the greenhouse simulator enable a 3D experience by virtual greenhouse for fruits and vegetable cultivation. At the same time, it is possible to visualize the greenhouse under various cultivation or climate conditions. The objective of this study is to apply the greenhouse climate management model for simulation development that can visually see the state of the greenhouse environment under various micrometeorological properties. The numerical solution with the mathematical model provided a dynamic change in the greenhouse environment for a particular greenhouse design. Light intensity, crop transpiration, heating load, ventilation rate, the optimal amount of CO₂ enrichment, and daily light integral were calculated with the simulation. The results of this study are being built so that users can be linked through a web page, and software will be designed to reflect the characteristics of cladding materials and greenhouses, cultivation types, and the condition of environmental control facilities for customized environmental control. In addition, environmental information obtained from external meteorological data, as well as recommended standards and set points for each growth stage based on experiments and research, will be provided as optimal environmental factors. This simulation can help growers, students, and researchers to understand the ICT technologies and the changes in the greenhouse microclimate according to the growing conditions.

• Journal of Intelligence and Information Systems
• /
• v.29 no.1
• /
• pp.121-142
• /
• 2023

As the number and weight of imported food are steadily increasing, safety management of imported food to prevent food safety accidents is becoming more important. The Ministry of Food and Drug Safety conducts on-site inspections of foreign food facilities before customs clearance as well as import inspection at the customs clearance stage. However, a data-based safety management plan for imported food is needed due to time, cost, and limited resources. In this study, we tried to increase the efficiency of the on-site inspection by preparing a machine learning prediction model that pre-selects the companies that are expected to fail before the on-site inspection. Basic information of 303,272 foreign food facilities and processing businesses collected in the Integrated Food Safety Information Network and 1,689 cases of on-site inspection information data collected from 2019 to April 2022 were collected. After preprocessing the data of foreign food facilities, only the data subject to on-site inspection were extracted using the foreign food facility_code. As a result, it consisted of a total of 1,689 data and 103 variables. For 103 variables, variables that were '0' were removed based on the Theil-U index, and after reducing by applying Multiple Correspondence Analysis, 49 characteristic variables were finally derived. We build eight different models and perform hyperparameter tuning through 5-fold cross validation. Then, the performance of the generated models are evaluated. The research purpose of selecting companies subject to on-site inspection is to maximize the recall, which is the probability of judging nonconforming companies as nonconforming. As a result of applying various algorithms of machine learning, the Random Forest model with the highest Recall_macro, AUROC, Average PR, F1-score, and Balanced Accuracy was evaluated as the best model. Finally, we apply Kernal SHAP (SHapley Additive exPlanations) to present the selection reason for nonconforming facilities of individual instances, and discuss applicability to the on-site inspection facility selection system. Based on the results of this study, it is expected that it will contribute to the efficient operation of limited resources such as manpower and budget by establishing an imported food management system through a data-based scientific risk management model.

• Journal of the Korean earth science society
• /
• v.43 no.6
• /
• pp.691-711
• /
• 2022

The state-of-the-art Earth system model as a virtual Earth is required for studies of current and future climate change or climate crises. This complex numerical model can account for almost all human activities and natural phenomena affecting the atmosphere of Earth. The Unified Model (UM) from the United Kingdom Meteorological Office (UK Met Office) is among the best Earth system models as a scientific tool for studying the atmosphere. However, owing to the expansive numerical integration cost and substantial output size required to maintain the UM, individual research groups have had to rely only on supercomputers. The limitations of computer resources, especially the computer environment being blocked from outside network connections, reduce the efficiency and effectiveness of conducting research using the model, as well as improving the component codes. Therefore, this study has presented detailed guidance for installing a new version of the UM on high-performance parallel computers (Linux clusters) owned by individual researchers, which would help researchers to easily work with the UM. The numerical integration performance of the UM on Linux clusters was also evaluated for two different model resolutions, namely N96L85 (1.875° ×1.25° with 85 vertical levels up to 85 km) and N48L70 (3.75° ×2.5° with 70 vertical levels up to 80 km). The one-month integration times using 256 cores for the AMIP and CMIP simulations of N96L85 resolution were 169 and 205 min, respectively. The one-month integration time for an N48L70 AMIP run using 252 cores was 33 min. Simulated results on 2-m surface temperature and precipitation intensity were compared with ERA5 re-analysis data. The spatial distributions of the simulated results were qualitatively compared to those of ERA5 in terms of spatial distribution, despite the quantitative differences caused by different resolutions and atmosphere-ocean coupling. In conclusion, this study has confirmed that UM can be successfully installed and used in high-performance Linux clusters.

• Economic and Environmental Geology
• /
• v.56 no.1
• /
• pp.23-53
• /
• 2023

In this review paper, previous studies on layered double hydroxides (LDHs) published in the Korean Citation Index (KCI) were examined to investigate a research trend for LDHs in Korea. Since the first publication in 2002, 160 papers on LDHs have been published until January 2023. Among the 31 academic fields, top 5 fields appeared in the order of chemical engineering, chemistry, materials engineering, environmental engineering, and physics. The chemical engineering shows the highest record of published paper (71 papers) while around 10 papers have been published in the other four fields. All papers were reclassified into 15 research fields based on the industrial and academic purposes of using LDHs. The top 5 in these fields are in order of environmental purification materials, polymer catalyst materials, battery materials, pharmaceutical/medicinal materials, and basic physicochemical properties. These findings suggest that researches on the applications of LDH materials in the academic fields of chemical engineering and chemistry for the improvement of their functions such as environmental purification materials, polymer catalysts, and batteries have been being most actively conducted. The application of LDHs for cosmetic and agricultural purposes and for developing environmental sensors is still at the beginning of research. Considering a market-potential and high-efficiency-eco-friendly trend, however, it will deserve our attention as emerging application fields in the future. All reclassified papers were summarized in our tables and a supplementary file, including information on applied materials, key results, characteristics and synthesis methods of LDHs used. We expect that our findings of overall trends in LDH research in Korea can help design future researches with LDHs and suggest policies for resources and energies as well as environments efficiently.

• The Journal of Korean Society for Radiation Therapy
• /
• v.34
• /
• pp.31-42
• /
• 2022

Purpose: This study measures and compares the surface dose values in the virtual target volume using Tomotherapy, Halcyon, and TrueBeam equipment using 6MV-Flattening Filter-Free(FFF) energy. Materials and Methods: CT scan was performed under three conditions of without bolus, 0.5 cm bolus, and 1 cm bolus using an IMRT phantom (IBA, Germany). The Planning Target Volume (PTV) was set at the virtual target depth, and the treatment plan was established at 200 cGy at a time. For surface dosimetry, the Gafchromic EBT3 film was placed in the same section as the treatment planning system and repeated measurements were performed 10 times and then analyzed. Result: As a result of measuring the surface dose for each equipment, without, 0.5 cm, 1 cm bolus is in this order, and the result of Tomotherapy is 115.2±2.0 cGy, 194.4±3.3 cGy, 200.7±2.9 cGy, The result in Halcyon was 104.7±3.0 cGy, 180.1±10.8 cGy, 187.0±10.1 cGy, and the result in TrueBeam was 92.4±3.2 cGy, 148.6±5.7 cGy, 155.8±6.1 cGy, In all three conditions, the same as the treatment planning system, Tomotherapy, Halcyon, TreuBeam was measured highly in that order. Conclusion: Higher surface doses were measured in Tomotherapy and Halcyon compared to TrueBeam equipment. If the characteristics of each equipment are considered according to the treatment site and treatment purpose, it is expected that the treatment efficiency of the patient will increase as well as the treatment satisfaction of the patient.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.3
• /
• pp.35-43
• /
• 2023

The purpose of this study is to research digital twin policies for the use of administrative services. The study was conducted through a mobile survey of 1,000 participants, and the results are as follows. First, in order to utilize digital twin technology, it is necessary to first identify appropriate services that can be applied from the perspective of Gyeonggi Province. Efforts to identify digital twin services that are suitable for Gyeonggi Province's field work should be prioritized, and this should lead to increased efficiency in the work. Second, Gyeonggi Province's digital twin administrative services should prevent duplication with central government projects and establish a model that can be connected and utilized. It should be driven around current issues in Gyeonggi Province and the demands of citizens for administrative services. Third, to develop Gyeonggi Province's digital twin administrative services, a standard model development plan through participation in pilot projects should be considered. Gyeonggi Province should lead the project as the main agency and promote it through a collaborative project agreement. It is suggested that a support system for the overall project be established through the Gyeonggi Province Digital Twin Advisory Committee. Fourth, relevant regulations and systems for the construction, operation, and management of dedicated departments and administrative services should be established. To achieve the realization of digital twins in Gyeonggi Province, a dedicated organization that can perform various roles in project promotion and operation, as well as legal and institutional improvements, is necessary. To designate a dedicated organization, it is necessary to consider expanding and reorganizing existing departments and evaluating the operation of newly established departments. The limitation of this study is that it only surveyed participants from Gyeonggi Province, and it is recommended that future research be conducted nationwide. The expected effect of this study is that it can serve as a foundational resource for applying digital twin services to public work.

• Korea Science and Art Forum
• /
• v.36
• /
• pp.391-400
• /
• 2018

To ensure a user-centered treatment environment, hospital construction needs an approach that is not centered on functional aspects such as efficiency or economic feasibility but on the consideration of needs as reflected in user psychology and behavior. Patients who are physically and psychologically vulnerable experience psychological pressure when they are placed in an unfamiliar environment. Most of existing studies however focus on the evaluation of the physical environment, without paying attention to the psychological or behavioral approach to anxiety and stress that patients may experience in a special environment that a hospital may be to them. This study examines general hospital inpatients to understand the usage of major space available and their satisfaction with privacy. This study provides useful primary information needed for the user-centered design of general hospital for improved patient health and welfare. For the purpose of the study, literature review, site investigation, and survey were conducted. Major functional space and privacy in general hospitals were studied, and the site investigation was performed to identify the plans and their status. Survey was also performed to understand the usage of functional space and satisfaction with such space usage as well as satisfaction with privacy. The findings were as follows: (1) Space usage was rated as average in general. It was found that patients used their rooms and lobby on a daily basis. By age, the usage was highest in the group in their 40s; the usage was relatively lower in the groups in their 30s or younger. (2) Space satisfaction was above average, indicating that patients were fairly satisfied. Satisfaction was highest in the lobby space designed with distinct features. By case, satisfaction was highest in Case B, characterized by its wide horizontal space in the rural settings. (3) Satisfaction with privacy in hospital was average, indicating that the demand for privacy was relatively higher but what patients receive in return was lower than their expectation. It was also found that satisfaction with privacy was a crucial element that affected the overall satisfaction with hospital.

• The Sea:JOURNAL OF THE KOREAN SOCIETY OF OCEANOGRAPHY
• /
• v.25 no.4
• /
• pp.117-131
• /
• 2020

Although most species in genus Zostera inhabit shallow coastal areas and bays with weak wave energy, the Asian eelgrass, Zostera asiatica is distributed in deep water depth (8-15 m) unlike other seagrasses on the eastern coast of Korea. To examine factors limiting distribution Z. asiatica in relatively deep coastal areas, a transplantation experiment was conducted on October 2011, in which Z. asiatica shoots were transplanted from the reference site (donor meadow, ~9 m) to the shallow transplant site (~3 m). We compared shoot density, morphology, and productivity of Z. asiatica as well as environmental factors (underwater irradiance, water temperature, and nutrients) between the reference and transplant sites from October 2011 to September 2012. Shoot density and shoot height of transplants dramatically decreased within a few months after transplantation, but were similar with Z. asiatica in the reference site during spring. Shoot productivity were significantly higher in the transplant site than in reference site because of high light availability and nutrient concentrations. Transplants showed photoacclimatory responses such as higher rETR_max and E_k and lower photosynthetic efficiency in the transplant site than those in the reference site. Most of Z. asiatica transplant in the shallow transplant site disappeared in summer, which may be due to the high wave energy and physical damages induced by typhoons (TEMBIN and SANBA) in August and September 2012. According to the results of this study, Z. asiatica could not survive in shallow areas despite of more favorable light and nutrient conditions. Thus, Z. asiatica may restrictively occur in deep areas to avoid the intense physical stresses in the shallow area on the east coast of Korea.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.30 no.2B
• /
• pp.121-135
• /
• 2010

This study is to assess the effect of potential future climate change on the inflow of agricultural reservoir and its impact to downstream streamflow by reservoir operation for paddy irrigation water supply using the SLURP. Before the future analysis, the SLURP model was calibrated using the 6 years daily streamflow records (1998-200398 and validated using 3 years streamflow data (2004-200698 for a 366.5 $km^2$ watershed including two agricultural reservoirs (Geumgwang8 and Gosam98located in Anseongcheon watershed. The calibration and validation results showed that the model was able to simulate the daily streamflow well considering the reservoir operation for paddy irrigation and flood discharge, with a coefficient of determination and Nash-Sutcliffe efficiency ranging from s 7 to s 9 and 0.5 to s 8 respectively. Then, the future potential climate change impact was assessed using the future wthe fu data was downscaled by nge impFactor method throuih bias-correction, the future land uses wtre predicted by modified CA-Markov technique, and the future ve potentiacovfu information was predicted and considered by the linear regression bpowten mecthly NDVI from NOAA AVHRR ima ps and mecthly mean temperature. The future (2020s, 2050s and 2e 0s) reservoir inflow, the temporal changes of reservoir storaimpand its impact to downstream streamflow watershed wtre analyzed for the A2 and B2 climate change scenarios based on a base year (2005). At an annual temporal scale, the reservoir inflow and storaimpchange oue, anagricultural reservoir wtre projected to big decrease innautumnnunder all possiblmpcombinations of conditions. The future streamflow, soossmoosture and grounwater recharge decreased slightly, whtre as the evapotransporation was projected to increase largely for all possiblmpcombinations of the conditions. At last, this study was analysed contribution of weather, vegetation and land use change to assess which factor biggest impact on agricultural reservoir and stream watershed. As a result, weather change biggest impact on agricultural reservoir inflow, storage, streamflow, evapotranspiration, soil moisture and groundwater recharge.