• 한국자동차공학회논문집
• /
• 제20권5호
• /
• pp.53-64
• /
• 2012

Deep and narrow welds can be produced by laser welding at high welding speeds with a narrow heat-affected zone (HAZ) and little distortion of the workpiece. This study aims to evaluate the usefulness of laser welding at automobile component manufacture. Microstructure observation, hardness test, tensile test and fatigue life test are performed by using the fiber laser welded SPFC590 steel sheets which is used widely in the manufacture of automotive seat frame. Three kinds of specimens are only a SPFC590 steel plate, quasi-butt joint plate and lap joint plate by laser welding. The following results that will be helpful to understand the static strength, fatigue crack initiation and growth mechanism were obtained. (1) The tensile strength of quasi butt joint specimens nearly equal to base metal specimens, but lap joint specimens fractured in shear area of weld metal. (2) The fatigue strength of quasi-butt joint specimen was approximately 8 percent lower than that of the base metal specimens. Furthermore, the lap joint specimens were less than 86 percent of the base metal specimens. (3) The lap joint fatigue specimens fractured at shear area in high level stress amplitude, while fractured at normal area in low level stress amplitude. From these results, the applicability of the laser welding to the automobile component is discussed.

• Journal of Welding and Joining
• /
• 제6권2호
• /
• pp.30-39
• /
• 1988

Generally, as the welded region of weld structures has the incomplete bead and welded deposit which are able to behave like the surface cracks occasinally, there is a high possibility that the fatigue fracture of the weld structures is due to the surface cracks on the wlded region. This study was done to investigate the effects of post weld heat treatment (PWHT) on the fatigue behaviors of the surface crack of the heat affected zone (HAZ) for the multi-pass welds under the repetitive pure bending moment. The obtained results are summarized as follows : 1. The crack grows to the depth direction initially as the number of cylces increase, the amount of crack length is increased for the surface dir3ction and cive versa for the depth direction. 2. The fatigue life is increased in a order of as weld, PWHT specimens and parent. 3. As the number of cycles increase, the crack length is increased to th surface direction. The increase of the depth length is blunted at the center of specimen thickness. 4. The fatigue crack growth of PWHT specimens to the surface direction is dependent upon the holding time and applied stress during PWHT. In order words, the crack growth rate decreases with the holding time and increases with the applied stress during PWHT. 5. As the crack grows, the aspect formed in the course of crack propagation approaches to semicircle for parent and ellipse with the largest semidiameter for PWHT ($1/4hr, 15kgf/mm^2$) 6. At depth direction, it is difficult to apply to the paris' equation because of the scattered data between the crack growth rate and the stress intensity factor range.

• Journal of Welding and Joining
• /
• 제17권5호
• /
• pp.47-54
• /
• 1999

It is well known that solidification cracking often occurs in welds of root pass for one-side welding under the conditions of high welding currents and speeds. In this study, the solidification in 590MPa class steel for pressure vessels SPPV490 was investigated by using flux-cored arc welding(FCAW) with 4 types of welding wires and welding conditions of 200∼280A and 2.8∼ 4.2mm/sec. In order to compared the result of cracking in SPPV490, 0.2%C steel for welded structure of SWS400 and 0.45%C steel for machine structural SM45C were also used as base metals. As the results, all the cracks formed in some welding conditions were observed near the center of weld bead. The solidification cracks were generally initiated near the upper surface of bead and propagated toward the inner part. The solidification cracking generally increased with welding current and welding speed in the same base metal and welding material. In cracking susceptibility, SPPV490 showed higher cracking susceptibility than SWS400 in all welding conditions and welding materials. It was considered that cracking susceptibility could not be evaluated with the hardness of weld metals. The cracking ratio increased with decreasing of a/b(a and b; the width of the upper surface and the back surface of the bead) as shape factor of bead. The cracking tendency with shape factor of bead was extended under the condition of higher welding currents.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.16-16
• /
• 2009

Alloy 82/182로 용접된 원자력 발전소 주기기의 이종 금속 용접부는 장기간 운전 후 응력부식균열(SCC : Stress Corrosion Cracking)에 의한 결함이 나타나게 된다. 2000년대 이후로 원자력 주기기 Alloy 82/182 용접부에서 PWSCC(Primary Water Stress Corrosion Cracking)에 의한 Degradation이 급격히 증가하는 추세를 보이고 있으며, 국내에서도 이와 관련하여 원자력 발전소의 안전성에 대한 Issue 및 대비책에 대한 관심이 고조되고 있다. 이러한 Alloy 600 용접부에 대한 결함을 예방하기 위한 대표적인 기술로써 수명연장 오버레이 기술이 있다. 원자력 주기기 노즐부는 저탄소강으로 제작되어 있으며, 저탄소강에는 제작 시 용접후열처리가 적용된다. 후열처리를 하는 주된 이유는 Tempering을 통해 열영향부의 인성 및 연성의 회복과 강도를 감소시켜 모재와 동등 또는 이 이상의 물성을 갖도록 하는 데 그 목적이 있다. 그러나 수명연장 오버레이의 경우 현장 작업 시에 후열처리가 어렵기 때문에, 이를 대체하기 위한 기술로 템퍼비드 용접을 적용할 경우 후열처리를 면제해 주고 있다. 본 연구에서는 수명연장 오버레이 기술 개발의 일환으로써 저 탄소강에 대한 템퍼비드 용접 기술을 확립하였다. 실험에 사용된 모재는 원자력 주기기의 노즐에 사용되는 SA508 Gr.3 Cl.1을 사용하였으며, 용가재는 Alloy 52 및 52M을 사용하였다. 최적 조건 도출을 위해서 실험 매트릭스를 이용하여 기본 실험을 수행하였으며, 실험에는 자동 GTAW 용접을 적용하였다. 기본 실험을 통해 얻은 최적 조건을 사용하여 PQ 시험을 수행하여 WPS를 확보하였다. 분석은 용접 후 조직 및 경도 시험, 물리시험(인장시험, 굽힘시험 및 충격시험)을 수행하였다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.41-41
• /
• 2009

To evaluate the applicability of dissimilar joining between Mg and Al alloys in automobile manufacturing process, solid state joining processes such as magnetic pulse welding(MPW), friction stir welding(FSW) and friction spot joining(FSJ) were attempted successfully. MPW process has been concentrated mainly on round section tube to tube and tube to bar welds. AZ31 Mg alloy has been successfully welded to pure Al A1070 as well as to Al alloy A3003. While, for friction stir welding of dissimilar sheet joints, AZ31B/A6061 with the thickness of 2mm were used and a square butt joint with a good quality was obtained at the conditions of 0.8mm/sec of travel speed and tool rotation speed of 850rpm. The maximum tensile strength of 179 MPa, which was about 80 % of the Mg base metal tensile strength, has been obtained. Finally, friction spot joining was attempted to make a dissimilar lap joint between AZ31(0.8mm) and A6061(1mm), while the joint exhibited the same level of tensile shear strength as that of similar Mg joint.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.68-68
• /
• 2009

최근에 자동차 차체 경량화를 목적으로 개발된 고장력강의 용접품질 향상을 위해 인버터 DC 점용접기가 많이 사용되어지고 있다. 본 연구에서는 국내에서 개발된 인버터 DC 용접기를 사용하여 자동차용 590MPa 고장력 냉연강판(CR, SPFC 590RA)과 아연 도금 강판 (GA- EZFFC 590RA)의 용접품질을 평가하였다. 용접에 사용된 기본 조건은 인장 전단 시험을 통하여 결정하였으며, 동저항, 압흔 자국과 너겟 지름, 인장강도와의 관계를 통계적 방법으로 분석하였으며, 이를 활용하여 고장력 강판의 동저항과 압흔 자국에 따라 너겟 지름과 용접강도를 예측하는 비파괴적 용접 품질 평가 방법을 제시하였다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.103-103
• /
• 2009

As the size of containership increased over 14,000TEU, thick steel plate with high strength has been used. The plate thickness increased over 70mm and yield strength of the steel plate was around $47kg_f/mm^2$. Many researchers reported that the thick welded plate has low crack arrest toughness. They noticed the crack arrest ability is dependent on the plate thickness. In other words, brittle crack propagates straightly along the welded line and make abrupt fracture in the thick plate which causes low $K_{ca}$. In this study, the other factors, especially welding heat input, to cause low crack arrest toughness was investigated for thick steel plate welds. EH grade steel plates were used in this study and 50 to 80 thick plates were tested to confirm thickness sensitivity. Electro gas welding (EGW) and flux cored arc welding (FCAW) were adopted to prepare the welded joints. Temperature gradient ESSO test was performed to measure $K_{ca}$ values with the variation of welding variables. As a result of this study, regardless of plate thickness, welding heat input to cause welding residual stress around crack path is a key factor to control the brittle crack propagation in welded joints.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.64-64
• /
• 2009

The use of ultra high strength steels (UTSS) is a natural result with increasing the demands for the lightweight materials and developing an innovative steel technology. Recently it has been used a 1500MPa grade hot stamping steel as automobile bodies, reinforcement parts, and seat frame parts in the automotive industry. It is a quenchenable steel manufactured by hot stamping process. It is well known that UTSS welding has softening in the heat affected zone(HAZ). Because welding is a sort of process applying heat, it should change the heat treated features and degrade the strength. This study was performed to investigate the influence of the heat input on the softening of the HAZ in the GMAW process. Each experiment was compared with that in the conditions having a different current and voltage at a same heat input. In order to analysis characteristics of the HAZ, optical microscope was used to observe microstructure and vickers hardness tests were carried out across the welds. Applying low heat input means a fast cooling rate. It leads to high hardness in the HAZ. It is found that characteristics of the HAZ are determined by microstructure obtained by different cooling rate.

• 대한기계학회논문집A
• /
• 제40권7호
• /
• pp.667-672
• /
• 2016

본 연구에서는 SS400에 대해 레이저-아크 하이브리드 용접을 이용하여 맞대기 용접을 실시하였다. 맞대기 용접시 입열에 직접적으로 영향을 미치는 레이저 출력, 용접 전류 및 속도를 변화시켜 실험을 실시하였다. 이를 통해, 결함 없이 원 패스 관통 용접이 이루어지고, 미려한 비드가 형성되는 최적의 맞대기 용접 조건을 도출하였다. 용접부의 기계적 및 조직적 특성을 파악하기 위해 레이저 및 아크 영역에 대해 경도측정 및 미세조직 관찰을 실시하였다. 또한 모재와 용접 시험편의 강도를 비교하기 위해 인장강도 실험을 실시하였으며, 결과적으로 두 시험편의 인장강도 값은 유사하게 나타나는 것을 확인할 수 있었다.

• Journal of Welding and Joining
• /
• 제33권1호
• /
• pp.35-40
• /
• 2015

Recently, there have been the increase of ship size and the development of oil and gas in arctic region. These trends have led to the requirements such as high strength, good toughness at low temperature and good weldability for prevent of brittle fracture at service temperature. There has been the key issue of crack arrestability in large size structure such as container ship. In this report for the first time, crack arrest toughness of thick steel plate welds was evaluated by large scale ESSO test for estimate of brittle crack arrestability in thick steel plate. For large structures using thick steel plates, fracture toughness of welded joint is an important factor to obtain structural integrity. In general, there are two kinds of design concepts based on fracture toughness: crack initiation and crack arrest. So far, when steel structures such as buildings, bridges and ships were manufactured using thick steel plates (max. 80~100mm in thickness), they had to be designed in order to avoid crack initiation, especially in welded joint. However, crack arrest design has been considered as a second line of defense and applied to limited industries like pipelines and nuclear power plants. Although welded joint is the weakest part to brittle fracture, there are few results to investigate crack arrest toughness of welded joint. In this study, brittle crack arrest designs were developed for hatch side coaming of large container ships using arrest weld, hole, and insert technology.