• Journal of Welding and Joining
• /
• 제15권6호
• /
• pp.85-95
• /
• 1997

This study is to investigate the optimum conditions of Nd:YAG laser beam welding for Zircaloy-4 end cap closure by optical fiber transmission. Laser welding parameters which affect the penetration depth and bead width were experimentally examined using the various beam radius by the beam quality analyzer, joint geometries of end cap and the laser parameters which mean pulse width, repetition rate and pulse energy. Also, an optimum welding speed and the effect of assistant gas with varying the flow rate of He were investigated. We found that the laser average power for the end cap welding will be 230W and rotation speed must not exceed 8 RPM, the best position of focus using optical fiber with 600.mu.m will be 2 to 3mm below the surface of the material.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 춘계학술발표대회 개요집
• /
• pp.68-70
• /
• 2002

A CCD camera with a laser strip was applied to realize the automation of welding process in GMAW. The Hough transformation was used to extract the laser stripe and to obtain specific weld points. In this study, a neural network based on the generalized delta rule algorithm was adapted for the process control of GMA, such as welding speed, arc voltage and wire feeding speed.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 1995년도 특별강연 및 춘계학술발표 개요집
• /
• pp.114-117
• /
• 1995

A study of friction welding of high speed steel(SKH51) bar for blade side to carbon steel(STC3) bar for shank side was carried out experimentally through tensile test, hardness lest, microstructure, and acoustic emission (AR) test. So, this paper deals with optimizing the welding conditions and the real-time quality(strength) evaluation of friction welded joints by acoustic emission technique.

• 융합정보논문지
• /
• 제9권7호
• /
• pp.94-99
• /
• 2019

마찰교반용접법(Friction Stir Welding, FSW)은 1991년에 영국 용접연구소 TWI(The Welding Institute)에서 최초 개발된 후 여러 산업분야에 걸쳐 적용연구가 활발히 진행되고 있다. 본 연구에서는 철도차량 차체의 주요 구성 소재인 알루미늄 합금 (Al-6005-T6) 평판 압출재에 대한 마찰교반접합 적용 기초연구를 수행하였다. 접합속도를 500 mm/min으로 고정한 채 회전공구의 회전속도를 600-1600 rpm으로 변화될 때 미세구조와 기계적 물성 변화에 미치는 영향에 대해 평가하였다. 경도 측정 결과 nugget부는 모재의 70% 수준의 경도값을 가지며 설정된 범위 내의 공구 회전속도와 연관성은 관찰되지 않았으며 용접계면에서 약 5 mm 벗어나게 되면 모재의 경도값을 가지는 것으로 확인되었다. 인장시험 결과 회전속도가 올라갈수록 항복강도와 인장강도가 소폭 하락하는 경향을 보였으며 연신률의 변화는 관찰되지 않았다.

• 한국산학기술학회논문지
• /
• 제17권10호
• /
• pp.280-288
• /
• 2016

본 연구의 목적은 마찰교반용접을 마그네슘 합금에 응용하기에 앞서 형상이 다른 두 종류의 용접 툴을 마찰교반용접 시험에 적용 및 비교하여 마그네슘 합금 마찰교반용접에 더 적합한 용접 툴을 제안하였다. 용접 툴의 효과를 알아보기 위해서 용접조건 변수 중 이송속도는 200mm/min으로 고정하였고 회전속도를 400, 600, 800rpm으로 변화시키면서 용접부의 거동과 용접 툴 변화에 따른 효과를 평가 및 관찰하였다. 기계적 물성 평가를 위해 인장시험과 경도시험을 수행하였으며, 용접부 내 거동 및 결함의 유무를 확인하기 위하여 용접부에 수직인 방향의 횡단면을 광학현미경을 통해 관찰하였다. 용접 툴에 관계없이 회전속도가 400rpm일 때 결함이 관찰되었으며, 회전속도가 증가할수록 결함이 감소하는 경향을 보였다. 최종적으로 회전속도 800rpm에서 결함이 없는 용접부를 얻었다. 용접 툴 변화에 따른 기계적 물성 평가 결과 C type 용접 툴을 적용한 경우 보다 우수한 결과가 나타났다. 기계적 물성이 가장 우수한 용접조건은 회전속도 800rpm, 이송속도 200mm/min 이었고, 이때 용접부의 인장강도, 항복강도 그리고 연신율은 모재 대비 90.0%, 69.1%, 83.2% 수준으로 각각 나타났다.

• 한국공작기계학회논문집
• /
• 제15권2호
• /
• pp.51-58
• /
• 2006

Laser welding of dissimilar metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research works is to investigate the influence of the process parameters, such as the welding for SM45C and STS304 with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the dissimilar welding, the welding quality of the cut section, stain-stress behavior and the hardness of the welded part are investigated. From the results of the investigation, it has been shown that the optimal welding condition without defects in the vicinity of the welded area and with a good welding qualify is 1600W of the laser power, 0.85m/min of welding speed and $4{\ell}/min$ of pressure for shielding gas.

• Journal of Welding and Joining
• /
• 제15권6호
• /
• pp.49-56
• /
• 1997

Effect of process parameters on the quality of condenser discharge weld for coated sheet steels was discussed. The welding specimens were coated with pure Zn of 20/20 g/m2 in the production line. Direct measurements of welding parameters such as the discharge current, the pressures and the voltage drop across the electrodes were carried out with welding process monitoring system. High speed camera was also utilized to analyze the weld formation process. Test results indicated that the relation between weld strength and applied energy was stabilized at the acceptable welding heat input range. It was thought that the acceptable welding heat input should be redefined based on the monitored data because the calculated value of the welding heat input could hardly be utilized if the discharge condition was changed. Mechanical test results and high speed photographs showed that expulsion deteriorated the weld quality and the strength at the same time especially when the size of the spatter was large enough to carry the molten metal, which should form the nugget, out of the welding spot. Results also demonstrated that the discharge current should be applied at the appropriate time during the process because sufficient nugget was not produced if the time was deviated from the optimum range.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.997-1003
• /
• 2005

Laser welding of dissimilar metals has been widely used to improve a wear resistance and a corrosion resistance of the industrial parts. The objective of this research works is to investigate the influence of the process parameters, such as the welding for SM45C and STS304 with CW Nd:YAG lasers. The bead-on-plate welding tests are carried out for several combinations of the experimental conditions. In order to quantitatively examine the characteristics of the dissimilar welding, the welding qualify of the cut section, stain-stress behavior and the hardness of the welded part are investigated. From the results of the investigation, it has been shown that the optimal welding condition without defects in the vicinity of the welded area and with a good welding quality is 1600W of the laser power, 0.85m/min of welding speed and 4m/min of pressure for shielding gas.

• Journal of Welding and Joining
• /
• 제16권2호
• /
• pp.29-36
• /
• 1998

• Journal of Welding and Joining
• /
• 제16권2호
• /
• pp.6-13
• /
• 1998