• 한국해양공학회지
• /
• 제19권6호통권67호
• /
• pp.64-71
• /
• 2005

The welding methods have been applied to the most structural products used in the automobile, ship construction, and construction. The structure steel must have sufficient strength of structure; However, the mechanical properties of the welded part changes when it is welded. Therefore, the stability or life of the structure may be affected by the changed mechanical properties. The mechanical properties of the welded part must be examined in order to ensure the safety of structure. In this research, the SS400 steel and the STS304 steel were used to estimate the mechanical properties of the HAZ by weld thermal cycle simulation. In this study, the materials were used to examine the weld thermal cycle simulation characteristic, under two conditions: the drawing with diameter of $\Phi$10 and the residual stress removal treatment. To examine the mechanical properties by the weld thermal cycle simulation, the tensile test was carried out in room temperature. The crosshead speed was lmm/min.

• 마이크로전자및패키징학회지
• /
• 제17권4호
• /
• pp.35-40
• /
• 2010

본 연구에서는 상용 고온 솔더 중 많이 쓰이고 있는 Sn-3.5Ag, Sn-0.7Cu, Sn-5.0Sb 솔더에 대한 열충격 시험, 열싸이클 시험, 고온 진동 복합 시험 신뢰성 평가를 하였다. 테스트 샘플을 제작하기 위해 Sn-3.5Ag, Sn-0.7Cu, Sn-5.0Sb 솔더볼을 ENIG 표면 처리된 BGA에 접합하였으며, 그 후 BGA샘플을 OSP 표면 처리된 PCB에 실장 하였다. 신뢰성평가 동안 저항변화를 측정하였으며 신뢰성 평가 전후 전단강도 시험을 통하여 접합강도의 변화를 평가하였다. Sn-3.5Ag의 솔더인 경우 전기저항과 접합강도의 저하가 비교 평가한 3가지 솔더 중 가장 높은 저하율을 보였으며 Sn-0.7Cu의 솔더가 신뢰성 평가 후에 비교적 높은 안정성을 나타내었다.

• Journal of Welding and Joining
• /
• 제33권3호
• /
• pp.62-67
• /
• 2015

A very large shell-structure built in shipyards like ship hulls or offshore structures are joined by welding through full process. As the welding contains a high thermal cycle at a local area, the welded structures should be distorted unavoidably. Because a distorted ship block should be revised to the designed value before the next stage, the ability to predict and to control the weld distortion is an accuracy level of the yard itself. Despite the ship block size, several present thermal distortion methodologies can deal those sizes, but it is a different story to deal full ship size model. Even a fully constructed ship hull not remaining any welding can have an accuracy issue like outfitting installation problems. Any present thermal distortion methodology cannot accept this size for its recommended element size and the number. The ordinary welding breadth at erection stage is about 20~40 mm. It can hardly be a good choice to make finite element model of these sizes considering human effort and computational environment. The finite element model for structure analysis of a ship hull is prepared at front-end engineering design stage which is the first process of the project. The element size of the model is as fine as the longitudinal space, and it is not proper to obtain a weld distortion at the erection stage. In this study, a methodology is suggested that a weldment can be shrunk at original place instead of using structural finite element model. We cut the original shell elements at erection weld-line and put truss elements between the edges of cut elements for weld shrinkage. Additional truss elements are used to facsimile transverse weld shrinkage which cannot be from the weld-line truss element shrink. They attach to weld-line truss element like twigs from barks. The capacity of developed elements is verified through an accuracy check of erection process of a container vessel at the apt. hull. It can be a useful tool for verifying a centering accuracy after renew and for block-separating planning considering accuracy.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.4-4
• /
• 2009

Polycarbonate (PC) and Acrylonitrile Butadiene Styrene (ABS) was welded through a combination of a diode laser and CNC. Laser beam passed the transparent PC and was absorbed in an opaque ABS. Polymers were melted and welded by absorbed and conducted heat. Experiments were carried out by varying working distance from 44mm to 50mm for the focus spot diameter control, laser input power from 10W to 25W, and scanning speed from 100 to 400mm/min. The weld bead size and the specimen cross-section were analyzed, and tensile results were presented through the joint force measurement. With focus distance at 48mm, laser power with 20W, and welding speed at 300mm/min, experimental results showed the best welding quality which bead size was 3.75mm and the shear strength was $22.8N/mm^2$. Considering tensile strength of ABS is $43N/mm^2$, shear strength was sufficient to hold two materials. A single process was possible in CNC machining processes, surface processing, hole machining and welding. As a result, the process cycle time was reduced to 25%. Compared to a typical process, specimens were fabricated in a single process, with high precision. By combining two operations processes developed process gained 50% more efficiency.

• Journal of Welding and Joining
• /
• 제34권3호
• /
• pp.47-51
• /
• 2016

Recently, the market of liquefied natural gas is growing in accordance with shale gas development and environmentally friendly policies. Also, LNG is in the spotlight as an alternative fuel to previously used fossil fuel and the fuel for the ship to meet emission standards which takes effected by IMO (International Maritime Organization). According to growth of LNG, LNG carriers needs are also expected to increase significantly. This study investigates low cycle fatigue (LCF) performance of 304L stainless steel weldments to investigate fatigue performance in plastic strain region. 304L stainless steel is known to have improved fatigue performance at cryogenic conditions. LCF behavior are investigated by a strain-controlled condition up to 1% strain range and conducted with three different thickness (3mm, 5mm, 10mm). Also, test were performed with three different strain ratio R such as R = -1, -0, 0.5, Finally, the fatigue design curve for 304L stainless steel weldments at room tem- perature are proposed. Considering all test conditions, it is shown that LCF performance have similar tendency regardless of thickness and strain ratio. LCF design curve of 304L stainless steel weldments are lower than 304L stainless steel base metal.

• 대한기계학회논문집A
• /
• 제41권3호
• /
• pp.193-198
• /
• 2017

Alloy 617은 초고온가스로(VHTR)의 중간열교환기(IHX)의 유력한 후보 재료 중의 하나이다. $850^{\circ}C$의 고온에서 Alloy 617 용접재의 저사이클 피로 거동을 고찰하기 위하여, 완전 양진 변형률제어 피로시험이 0.6에서 1.5%의 전변형률범위에서 수행되었다. 용접재 시험편은 V-그루브 형상의 가스텅그스텐아크 용접한 용접 패드로부터 가공되었다. 피로수명은 전변형률범위가 증가할수록 감소하였다. 모든 실험조건에서 Alloy 617 용접재 시험편의 반복 응력 반응 거동은 초기 수 사이클에서 반복 변형률 경화현상을 나타내었다. 또한 모든 피로 균열의 발생과 전파는 입내파괴의 파손 모드를 보였다.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.117-117
• /
• 2009

저항 점 용접 시스템은 SCR 방식과 Inverter 방식으로 나뉘어지는데 현재 공급전원의 안정화 및 고속의 제어가 가능한 Inverter 방식으로 점차 변해가는 추세이다. 이러한 추세에 따라 기존 SCR 방식에서는 구현하기 힘들었던 고속의 전류제어가 요구되고 있으며 여러 제어 알고리즘들이 적용되고 있다. 일반적으로 전류를 제어하기 위해 PI제어 알고리즘이 많이 사용되고 있다. PI제어보다 좀더 반응이 빠르고 정밀한 제어 알고리즘의 적용이 시도되고 있지만 실질적으로 현장에 적용하여 활용하기에 어려움이 있어 PI제어가 많이 선호되고 있다. 일반적으로 용접전류의 제어는 일정한 전류를 공급할 수 있게 하는 것이 주요하지만 저항 점 용접 시스템에서는 일정한 전류의 공급 이외에 목표 전류까지 도달하는 응답시간 또한 주요한 사항으로 작용하고 있다. 이는 짧은 통전시간으로 인해 응답성에 따라 입열량의 차이가 나타나기 때문이다. 응답시간이 느릴수록 그만큼 전류의 공급이 적어지고 이로 인해 입열량이 감소하게 된다. 국내의 Inverter 방식의 경우 응답시간이 15ms 이상이지만, 해외 선진 제품의 경우 10ms 이하의 응답시간을 가져 크게는 1cycle(16.6ms)의 차이가 나고 같은 용접전류 조건에서도 용접성의 차이가 나타나게 된다. 본 연구에서는 응답시간에 따른 용접성의 변화와 응답시간 제어의 필요성을 확인하기 위해 PI제어기를 응답시간에 따라 설계하고 이를 자체 제작한 Inverter DC 저항 점 용접기에 적용하여 용접실험을 실행하였다. 용접소재로는 현 자동차용 강판 소재인 SPFC590, 1mmt를 사용하였고 인장 및 단면시험을 통해 용접성을 비교하였다. 또한 각각의 로브곡선을 도출하고 비교하여 응답시간에 따른 용접성의 차이를 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권4호
• /
• pp.464-471
• /
• 2002

Porosity formation in partial penetration welds by high power lasers is a serious problem in industry. There are two main causes that induce porosity formation. One form of porosity is due to gases (e.g. hydrogen, oxygen) dissolving into the weld pool because of the high temperature and then the rapid solidification traps gases as a bubble in the weld metal. The second problem is voids formed by the keyhole collapsing due to unstable keyhole fluid dynamics. The voids that form at the bottom of the keyhole are relatively large and irregular in shape compared to the gas bubbles; this void formation is the primary concern in this paper. The reduction of voids formed by keyhole collapse is achieved by improving the stability of keyhole. Two methods to improve keyhole stability are discussed in this paper: pulse modulation and beam incident angle. Pulse modulation of the laser beam was performed between 100 Hz and 500 Hz to find out the optimum frequency for the keyhole dynamics. The incident beam angle changed the impact angle of the laser beam to the work surface in a range of 0 to 25 degrees. Glycerin in a semi-solidified state is used as a medium for performing the welding because its transparency allows of visualization of the keyhole.

• Journal of Welding and Joining
• /
• 제12권2호
• /
• pp.87-96
• /
• 1994

Correlation between microstructural features and segregation of elements (Si, Mn, P and S) near the mid of thickness in the base metal and the synthetic HAZ was investigated. Furthermore, the relationship between the degree of center segregation and weld cold cracking susceptibility in the thickness direction was also conducted by evaluating the effect of P concentration on the critical applied stress. The results obtained are as follows: 1) Pearlite band, containing the MnS type inclusion and a locally transformed structure with a higher hardness, was observed in the center segregation region. 2) By the weld thermal cycle, center segregation region was transformed to the white band which had a higher hardness than that of base metal due to a greater hardenability of concentrated Mn, P etc.. 3) Weld cold cracking susceptibility in the thickness direction was mainly dependent on the concentration of impurity elements rather than on the number of the segregated particles near the mid of thickness. 4) During welding, the higher concentrated region was easily changed into white band. Therefore, it could be predicted that the initiation and propagation of a cold crack would be promoted by increasing the restraint stress and hydrogen content.

• International Journal of Korean Welding Society
• /
• 제4권1호
• /
• pp.61-66
• /
• 2004

In this paper, the effect of underfill packages was investigated by numerical approach and experimental test. Reliability improvement was the main issue in the package technology. BGA, CSP and small-sized packages, have problems due to concentration of the stress in solder joints. One of the latest technologies to overcome is underfill encapsulant. Mainly, it is noticed the effect of the underfill in the packages. The predicted thermal fatigue lifes are performed by Coffin-Manson's equation with ANSYS (v.5.62). Also, thermal cycle test during from 218K to 423K was included. Finally we could find that underfill greatly reduce the concentration stress in solder joint, thus the fatigue life was improved than without underfill.