• Journal of Welding and Joining
• /
• v.21 no.5
• /
• pp.540-546
• /
• 2003

Recently Al alloys are being used gradually for structural materials of transports. In welding of Al alloys used for transports, good weldabilities as well as adequate mechanical properties of the welds should be ensured as structural materials. In this study, the welds formation, macro and microstructural characteristics, generation of defects and hardness distribution in welds of Al alloys of 5083, 6N01 and 7N01 by DCSP- and AC-GTA welding process, were investigated. The deeper penetration was obtained in all welds of the alloys by DCSP-GTAW with He gas, compared with those by using AC-GTAW. The 6N01 alloy showed high susceptibilities to solidification cracking in weld metal and liquation cracking in HAZ of the welding beads of both DCSP- and AC-GTAW process. The cracking ratio of 6N01 alloy was increased with increasing of welding current. The porosity ratios in weld metal of all alloys used were extremely low including all welding conditions of DCSP-GTAW. However, in AC-GTAW process, the porosity ratios of the welds using Ar gas showed much higher values than those using He gas.

• Journal of Welding and Joining
• /
• v.34 no.4
• /
• pp.40-47
• /
• 2016

The Zn coating on automotive galvanized steel sheets can improve corrosion resistance. However, the boiling temperature of Zn is lower than the melting temperature of steel and it causes well-known spatter and porosity problem. One of most prominent solutions is a pretreatment of Zn coating by an additional welding arc prior to the main welding process. In this research, GTA and GMA are selected as heat sources for pretreatment and main welding processes, respectively. The authors suggested three possible mechanisms to reduce weld defects by the GTA pretreatment: (1) Formation of gap between the sheets; (2) Evaporation of Zn layer; (3) Oxidation of Zn layer. Among them, Zn Oxidation is the most important mechanism to reduce weld defects in the GTA-GMA hybrid process.

• Journal of Surface Science and Engineering
• /
• v.35 no.3
• /
• pp.113-120
• /
• 2002

Injection molded plastic parts have many surface defects. These include a weld line, sink mark, flow mark, gloss, shading, scratching etc. Because these surface faults are not aesthetically acceptable, plastic parts are produced through painting or texturing. The purpose of this paper is to develop paintless molded parts using a flow control method. Computer aided injection mold filling simulations were used in order to minimize the number of defects from injection molding. Based on the numerical results, FR(Flame Retardant) HIPS was developed and the guidelines for part design, mold design, and the processing conditions were established. The effects of cost savings, improvements in productivity, and recycling were considered by reducing the number of surface faults and eliminating the painting process.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.12 no.6
• /
• pp.56-63
• /
• 2003

In this study, an automatic ultrasonic testing system is used to detect the defects of the natural flaw test specimen and of the artificial flaw test specimen. We evaluate the detection performance of the acceptance standard for the natural flaw test specimen and of the acceptance standard for the artificial flaw test specimen. We also study the potential problems of those acceptance standards. The results indicate that the acceptance standard for the detection of defects in weldzone is good then the sensitivity correction is performed and that we must clearly specify special check points of the acceptance standard for the system in use.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.6
• /
• pp.1001-1008
• /
• 2012

Non-destructive testing (NDT) is a technique used in science and industry to evaluate the properties of a material without causing damage. In this paper we propose a method for segmenting radiographic images of welding in order to extract the welding defects which may occur during the welding process. We study different methods of level set and choose the model adapted to our application. The methods presented here take the property of local segmentation geodesic active contours and have the ability to change the topology automatically. The computation time is considerably reduced after taking into account a new level set function which eliminates the re-initialization procedure. Satisfactory results are obtained after applying this algorithm both on synthetic and real images.

• Design & Manufacturing
• /
• v.13 no.3
• /
• pp.29-34
• /
• 2019

Cell phone injection is characterized by its small size and thinness. In addition, the product has a short cycle time, requiring a very short production schedule. To produce more accurate products faster, data from experience in producing similar products is required. In this study, two mobile phone models are presented. In this study, the quality problems caused by molding analysis and actual injection molding were analyzed and made into a database. As a result, it was considered that all the defects in the molding analysis do not affect the product in some cases, rather than appear as defects in the actual product. All defects shown in the molding analysis can be made into a database, and based on this data, it will be possible to obtain an effect that can predict more accurately whether it will cause problems after injection.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.10
• /
• pp.1507-1512
• /
• 2010

In this study, the plasma induced by $CO_2$ laser lap welding of 6t Zn coated steel used for ship building was measured using photodiodes and a microphone. Then, the welding phenomenon with gap clearance of lap joint was compared with RMS-treated signal. Thus, we found that intensity of the RMS-treated signal increased with Zn vaporization; further, the presence of defects results in rapid variations with the RMS value as a function of lap-joint parameters. Besides, the FFT value of the raw signal with variations of changing welding parameters was calculated, and then the calculated FFT frequency value was set as the bandwidth of digital filter for a more accurate in-process monitoring. The RMS values were acquired by filtering the raw signal. By matching the weld beads and the calculated RMS values, we confirmed that there is a strong relationship between the signals and the defects.

• Journal of the Korean Society of Safety
• /
• v.34 no.6
• /
• pp.7-12
• /
• 2019

Flux Cored Arc Welding (FCAW), which has been widely used in many industries, was developed in the 1950s to supplement shortcomings of the Shielded Metal Arc Welding (SMAW). FCAW has an advantage in that it can weld regardless of postures and give good quality results in the filed with many different working conditions. In this study, SM490A (rolled steel for welding structural purpose) with different thicknesses (L:25T+R:30T) were welded using FCAW. Then the mechanical properties (tension test, bending test, hardness test, impact test and macro test) were analyzed and the following conclusions were drawn. In the tensile test, it exceeds the KS standard tensile strength range (400~510) in all welding positions, which means there is a problem in the tensile force transmission performance. In the bending test, it was found that most of the specimens did not exhibit surface rupture or other defects during bending test and they exhibit sufficient toughness even after plastic deformation. In the hardness test, all the results were lower than the standard value of 350 Hv of KS B 0893, which means they have good hardness. In the impact test, all results were larger than the KS reference value of 27J. In the macro test, they showed uniform structure state by the shape of the weld, and there was risk of lamination because no internal defects, bubbles, or impurities were found on the surface of the weld.

• Journal of Power System Engineering
• /
• v.13 no.5
• /
• pp.95-102
• /
• 2009

A steam generator (boiler) in thermal power plants, consisting of more than 30,000 parts and components, can lead to the plant shutdown with damage to even the small part of the components; esp., like weld failures on boiler tubes. Consequently it is greatly demanded to improve the quality of the weld on the boiler tube for the stable operation of the power plants. Because of the feature of the welding, which is done past by melting the work pieces and adding a filler material that cools to become a strong coalescence, there is a great possibility that weld failures take place. As a result, it is regulated to make a non-destructive testing, like radiography test, to detect defects and flaws in the weld. The current film radiography test provides a lower image quality exceeding 2.0% of a basic quality level for a penetrameter, it is very likely to fail to detect micro defect. As a result, the prevention for the boiler tube failure has not been made effectively. In this study, computed radiography technology has been applied as a digital radiography test to the boiler tube weld, and Se-75 radiation source was used to improve the image quality, instead of Ir-192 source. As a result of this study, it is proven to save the time and cost for test and to enhance the quality level of penetrameter penetrating image, which enables to upgrade the quality of radiography test to the boiler tube weld.

• Journal of the Korean Institute of Gas
• /
• v.4 no.1 s.9
• /
• pp.9-15
• /
• 2000

In order to investigate the structural defects of a cylindrical-type toluene storage tank, we carried out the acoustic emissions. The storage tank was manufactured with high strength steel in 1978 and its's first and second courses from bottom were entirely repaired, recently. Acoustic emissions were monitored with real time according to load sequences in the $75{\~}84\%$ level range of maximum allowable load. Our results show a non-genuine acoustic emissions as well as a genuine characteristics. The pseudo emissions considered as valve noises were transiently occurred on shut-off processes of inlet valve regardless of water loading. The acoustic emission events occurred during water filling phase were estimated due to defects, and in the $75{\~}84\%$ test load level no evidences of defect growth were observed. Those defects were ascertained as weld cracks and porosities through the post radiography testing conducted near active sensors.