• Journal of Bio-Environment Control
• /
• v.30 no.1
• /
• pp.27-36
• /
• 2021

A capacitive water sensor was developed to measure the capacitance over a wide part of a substrate using an insulated electrode plate (30 cm × 10 cm) with copper and Teflon attached on either side of the substrate. This study aimed to convert the capacitance output obtained from the condenser-type capacitance sensor into the substrate water content. The quantification experiment was performed by measuring the changes in substrate water weight and capacitance while providing a nutrient solution and by subsequently comparing these values. The substrate water weight and capacitance were measured every 20 to 30 seconds using the sensor and load cell with a software developed specifically for this study. Using a curve-fitting program, the substrate water content was estimated from the output of the capacitance using the water weight and capacitance of the substrate as variables. When the amount of water supplied was increased, the capacitance tended to increase. Coefficient of variation (CV) in capacitance according to the water weight in substrate was greater with the 1.0 kg of water weight, compared with other weights. Thus, the fitting was performed with higher than 1.0 kg, from 1.7 to 6.0 kg of water weight. The correlation coefficient between the capacitance and water weight in substrate was 0.9696. The calibration equation estimated water content from the capacitance, and it was compared with the substrate water weight measured by the load cell.

• Journal of Information Technology Services
• /
• v.16 no.2
• /
• pp.129-138
• /
• 2017

This paper is concerned with an Internet of Things (IoT)-based unmanned home-delivery box system, in which the system is developed with a prototype using a weight sensor, shock sensor, the Arduino and Raspberry-Pi of open-source hardware platforms. The developed system provides several functions such as a safe storage means, prevention of delivery-theft, and remote control of the home-delivery box, etc. Specifically, the system recognizes the arrival of goods by detecting the weight of deliveries and sends the arrived message of deliveries to the recipient' smartphone, and also controls (i.e., open and close) the locker of the unmanned home-delivery box system remotely with the smartphone. Furthermore, the developed system provides automatically a warning alarm around the unmanned home-delivery box when an external shock is applied to the home-delivery box, and sends a message on the shock to the recipient' smartphone. The major functions of the developed home-delivery box system have been verified in a realistic environment, and confirmed to work well. With the application of the developed home-delivery box system to the homes and offices where recipients are always not to stay, it is expected to significantly improve the safety of delivered goods as well as to effectively prevent the delivery operatives posing as a crime.

• Design & Manufacturing
• /
• v.2 no.5
• /
• pp.30-33
• /
• 2008

Injection Molding is the most effective process for mass production of plastic parts. The injection molding process is composed with several steps such as Filling, Packing, Holding, Cooling, Ejecting. Among them, filling and packing process should be considered carefully to improve accuracy of dimension, surface quality of plastic parts. Usually the quality above-mentioned is managed with weight of part after molding on the field. In this paper, a series of experiment for molding automotive front bumper was conducted with cavitity temperature sensor to optimize switch-over time(V-P switching), hot runner vale gate sequence time during filling and packing step for the purpose of uniform quality, weight at every molding. As a result, it was found that it is effective method to use temperature sensor in injection molding for quality control of plastic molding.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.314-320
• /
• 2014

Field balancing is required in any kind of phase information for the determination location balancing mass toward a rotor unbalance mass. Phase or phase angle is a measurement of the relationship of how one vibration signal which relates to another vibration signal and is commonly used to calculate the placement of balance weight. In this paper, A right guideline shows the photo optical speed sensor as the external keyphasor is a very useful when diagnosing machinery vibration problems on considering a phase lag comparing to the laser optical speed sensor. Some experimental results generate the interesting phase errors when appling to a wrong conditions. So, Usage of photo optical speed sensor which is used primarily to measure the shaft rotating speed serves as a reference for measuring vibration phase information has effect on the placement of phase angle how it was misunderstood. This paper will help a right method to search for the position of balancing weight and serves as baseline for further measurements using low cost and much easier user convenience. It is concluded that the propose baseline is likely to be applicable to apply to the practical field balancing weight.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.2
• /
• pp.101-107
• /
• 2015

Field balancing is required in any kind of phase information for the determination location balancing mass toward a rotor unbalance mass. Phase or phase angle is a measurement of the relationship of how one vibration signal which relates to another vibration signal and is commonly used to calculate the placement of balance weight. In this paper, A right guideline shows the photo optical speed sensor as the external KeyPhasor is a very useful when diagnosing machinery vibration problems on considering a phase lag comparing to the laser optical speed sensor. Some experimental results generate the interesting phase errors when appling to a wrong conditions. So, Usage of photo optical speed sensor which is used primarily to measure the shaft rotating speed serves as a reference for measuring vibration phase information has effect on the placement of phase angle how it was misunderstood. This paper will help a right method to search for the position of balancing weight and serves as baseline for further measurements using low cost and much easier user convenience. It is concluded that the propose baseline is likely to be applicable to apply to the practical field balancing weight.

• Journal of the Semiconductor & Display Technology
• /
• v.12 no.1
• /
• pp.15-21
• /
• 2013

In this paper, sensor system and inspection algorithm in order to inspect steel balance weight for automobile is described. Steel balance weight is composed of clip and weight, which is joined by press process. The defective one has a gap between clip and weight. To detect whether there is a gap, sensor system is simply configured with laser line projector and USB camera, which make it possible to measure the height difference of clip and weight area. Laser line pattern which is made on the surface of a balance weight is captured by USB camera. In case that USB camera is used in machine vision, barrel distortion caused by wide angle lens makes the captured image distorted. Image warping function is applied to correct the distortion. Simple image processing algorithm is applied to extract the laser line information and whether it is good or not is judged through the extracted information.

• International Journal of Automotive Technology
• /
• v.7 no.2
• /
• pp.195-199
• /
• 2006

According to the United States FMVSS 208, every passenger car on the market after September of 2006 must install a safety system, which can deploy the airbag with different intensity or suppression based on the passenger type, to reduce infant and child injuries from airbag deployments. The Weight Classification System, which has been developed by Hyundai Autonet, is a system that classifies the person occupying the passenger seat. To overcome sensing problems due to the weight sensors small voltage, the Distributed Systems Interface is adopted.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.2 no.3
• /
• pp.138-144
• /
• 2007

Wireless Sensor Network(WSN) consists of a lot of light-weight sensor nodes with the capability of wireless communication. Studies have been done to improve stability and fault-tolerancy of WSN because the sensor nodes are basically vulnerable to the harsh environment. Specially, the time synchronization among sensor nodes becomes a challenging issue in WSN. All the local times should always keep the same with each other in the sensor field to perform data aggregation and energy-aware communication in WSN. In this paper, a new time synchronization technique is proposed to operate efficiently irrespective of the number of sensor nodes and the number of hops needed to cover all sensor nodes for synchronization. Simulation results show that the proposed technique has the lowest amount of packet traffic among the several time synchronization techniques.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.3
• /
• pp.128-133
• /
• 2008

In this paper, in order to analyze property of frequency response in microphone using optical sensor, acousto-optic sensor system has been implemented. The capacitance microphone and fiber-optic transmission path type fiber-optic microphone (FOM) have weaknesses in directivity, size, weight, and price. However suggested optical microphone can be constituted by cheap devices, so it has many benefits like small size, light weight, high directivity, etc. Head part of optical microphone which is suggested in this paper is movable back and forth by sound pressure with the attached reflection plate. Operating point has also been determined by measuring the response characteristics. The choosing the point, which has maximum linearity and sensitivity has changing the distance between optical head and vibrating plate. We measured the output of the O/E transformed signal of the optical microphone while frequency of sound signal is changed using sound measurement /analysis program, "Smaart Live" and "USBPre", which are based on PC, and compared the result from an existing capacitance microphone. The measured optical microphone showed almost similar output characteristics as those of the compared condenser microphone, and its bandwidth performance was about 4 kHz at up to 3 dB.

• Journal of the Korean Society of Safety
• /
• v.30 no.3
• /
• pp.93-99
• /
• 2015

Economic burden of work-related musculoskeletal disorder(WMDs) is increasing. Known causes of WMDs include improper posture, repetition, load, and temperature of workplace. Among them, improper postures play an important role. A smart sensor called SensorTag is employed to estimate the trunk postures including flexion-extension, lateral bend, and the trunk rotational speeds. Measuring gravitational acceleration vector in the smart sensor along the tri-orthogonal axes offers an orientation of the object with the smart sensor attached to. The smart sensor is light in weight and has small form factor, making it an ideal wearable sensor for body posture measurement. Measured data from the smart senor is wirelessly transferred for analysis to a smartphone which has enough computing power, data storage and internet-connectivity, removing need for additional hardware for data post-processing. Based on the estimated body postures, WMDs risks can be conviently gauged by using existing WMDs risk assesment methods such as OWAS, RULA, REBA, etc.