• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.304-311
• /
• 2001

This research numerically analyzes the dynamic characteristics of a coupled journal and thrust hydrodynamic bearing due to its groove location which has the static load due to the weight of a rotor in the axial direction and the dynamic load due to its mass unbalance in the radial direction. The Reynolds equation is transformed to solve a plain member rotating type of journal bearing(PMRJ), a grooved member rotating type of journal bearing (GMRJ), a plain member rotating type of thrust bearing (PMRT) and a grooved member rotating type of thrust bearing (GMRT). FEM is used to solve the Reynolds equations in order to calculate the pressure distribution in a fluid film. Reaction forces and friction torque are obtained by integrating the pressure and shear stress along the fluid film, respectively. Dynamic behaviors, such as whirl radius or floating height of a rotor, are determined by solving its nonlinear equations of motion with the Runge-Kutta method. This research shows that the groove location affects the pressure distribution in the fluid film and consequently the dynamic performance of a HDD spindle system.

• 대한방사선협회지
• /
• 제28권1호
• /
• pp.212-212
• /
• 2002

• Tribology and Lubricants
• /
• 제30권1호
• /
• pp.9-14
• /
• 2014

In this Part II study, rotordynamic stability analyses were carried out to confirm improvements to the stability of a process high-speed lightweight centrifugal compressor, depending on the effects of tilting pad journal bearing designs. The bearing design variables considered were the clearances, LBPs, LOPs, and preloads. The results showed that the rotordynamic stability of the subject compressor rotor-bearing system improves exactly in accordance with the effects of the bearing design variables, which were determined in the preceding Part I study, owing to reduced bearing stiffnesses. Specifically, it was confirmed that the stability of the rotor system can be greatly improved by increasing both the machined and assembled bearing clearances, but there were no stability improvements by simply changing from an LBP to an LOP design. In addition, it was confirmed that for given fixed machined bearing clearances, the stability can be additionally improved by decreasing the preloads, i.e., by increasing the assembled clearances. In conclusion, it may be necessary to improve the designs of the original tilting pad bearings to obtain a sufficient margin of rotordynamic stability against a possible aerodynamic cross-coupled stiffness in a process high-speed centrifugal compressor. Thus, increasing the machined and assembled bearing clearances and decreasing the preload could be effective solutions.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.181-186
• /
• 2002

Lately, as going on increasing in the demand of high power density(power/weight), it is necessary for hydraulic axial piston pump/motor to operate more high pressure and speed. But in these condition, there are some trouble like as friction loss. To reduce this friction loss, hydrostatic bearing is used far axial piston pump/motor frequently. In general, it is difficult to measure accurate friction torque of spherical hydrostatic bearing in the use of the existing devices. So, we have developed the measurement device using the reaction torque sensor to obtain the pure friction torque, fitted in the casing. In this report, we intend to make an introduction about this measurement device for friction torque of the spherical wear part and clarify the effect of friction characteristics on supply pressure and rotational speed with three types of pocket size by using this measurement device.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1998년도 유체기계 연구개발 발표회 논문집
• /
• pp.159-165
• /
• 1998

Bearing design of turbo type geared centrifugal air compressor for low vibration level has been studied. The Transfer Matrix Method was used in this paper to analyze the air-compressor consisting of impellers, multi-stage geared rotors, and oil-film hearings. We have to consider this air-compressor as multi-geared rotating system, because characteristics of rotor-bearing system are different from conventional characteristics of non-rotating system. From the view point of Rotordynamics, the stiffness and damping coefficient of oil-film bearing in case of compressor system are more sensitive than other design parameters such as shaft length, shaft diameter and the weight of impellers, etc. Therefore, the stiffness and damping coefficients on each bearing were considered as design parameters. As the result of this study, turbo type air compressor with low vibration level can be achieved.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2001년도 유체기계 연구개발 발표회 논문집
• /
• pp.129-134
• /
• 2001

The paper presents the optimal design of a oil-free two-stage compressor, which is driven by 75 kW motor at an operating speed of 39,000 rpm, and the pressure ratio of which is up to 4. First, an attempt is made to obtain the optimal design of a bump bearing which supports a compressor rotor. Second, bump bearings and shaft are considered simultaneously, and the weighted sum of rotor weight and frictional torque is minimized. Finally, the optimal geometry of compressor wheel is considered. The mean efficiency and the - minimum efficiency are maximized respectively. The results presented in this paper provide important design information necessary to reduce the energy loss.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2005년도 후기학술대회논문집
• /
• pp.21-22
• /
• 2005

A study on the wear characteristics of the white metal(Sn-base alloy) bearing as a function of particle contamination level was conducted in order to establish control criteria of the lubricant in the 2-stroke marine diesel engine. Particle contamination level of the lubricants ranged from NAS 10 to 12 for the experiments. Bar-on-plate type wear test was performed using reciprocating wear tester. Based on this study it was found that there was no noticeable difference in weight loss of the white metal for NAS10 and NAS11(particle contamination level). Surface roughness of the white metal bearing after the wear test of 8hrs for the highly contaminated lubricant(NAS12 level) was up to $6{\mu}m$ in Rmax whilst that of the less contaminated lubricants(NAS10 & 11) was less than $1.5{\mu}m$ in Rmax.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1997년도 춘계학술대회논문집; 경주코오롱호텔; 22-23 May 1997
• /
• pp.272-277
• /
• 1997

The axial bearing using two ring type permanent magnets to support the weight of a flywheel is proposed to reduce the bearing loss in a flywheel energy storage , system. Two permanent magnet makes stable force in axial direction but unstable force in lateral direction. The lateral unstable stiffness is identified quantitatively using flux analysis, and then through the rotor dynamic analysis on a rigid flywheel system the unstable effects on the system by the stiffness is investigated.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.993-996
• /
• 2005

This paper is concerned with transfer process on hot forging of bearing hub. Workers on hot forging have difficulty in working by high temperature and weight workpiece. And In conventional got forging of bearing hub, the material wasted to the flash accounts approximately 10% of the original workpiece. It is need manufacture automation and reduce the cost of forged products. Surface treatment of die and lubricant are investigated from experiment and FE-simulation for analysis of forming simulation. In order to hot forging process design considered flash thickness and blocker geometry and initial temperature of die and billet. This transfer process gave comparatively good results compared with actual products.

• 농업과학연구
• /
• 제42권4호
• /
• pp.293-297
• /
• 2015

This study was conducted to evaluate the influence of feeding leaf positions on the growth, net formation of fruits, and occurrence of leaf yellowing symptoms (LYS) in muskmelon plants. Plants having five or ten more leaves above the fruit-bearing node produced the greater biomass than those of plants having equal or five less leaves above the fruit-bearing node. The number of leaves above the fruit-bearing node also influenced on the occurrence of LYS. The number of plants with LYS decreased as the number of leaves borne on the nodes above the fruit-bearing node increased. The LYS infected ratio of BL-5 treatment were the greatest, while fruit weight of BL+5 treatment were the greatest among all the tested treatments. In addition, the net formation of BL-5 treatment showed the poorest. Results indicated that maintaining the higher number of leaves over the fruit-bearing node might be feasible the practical method for coping physiological damages from yellowing symptoms.