• 분석과학
• /
• 제29권5호
• /
• pp.219-224
• /
• 2016

A sensitive method to detect trace anions in hydrofluoric acid (HF) by solid-phase extraction (SPE) clean-up and ion chromatography (IC) was described. Fluoride in HF solution was eliminated with solid-phase extraction, and residual fluoride, acetate, chloride, bromide, nitrate, phosphate and sulfate were consecutively separated with IC. The SPE parameters (selection of adsorbent, sample volume and pH, elution solvent and its volume) were optimized and selected. The removal effect of fluoride in HF solution was the best on Oasis WAX column, and the optimum conditions (1.0 mL of 25 % HF solution and 50 mM ammonium acetate 5 mL as elution solvent) were established by the variation of parameters. Under the established condition, the method detection limits of chloride, bromide, nitrate, phosphate, and sulfate were 0.04~0.30 µg/L in 25 % HF solutions (w/w) and the relative standard deviation was less than 5 % at concentrations of 20.0 and 40.0 µg/L. The concentrations of anions in a 25 % HF had detectable levels of 4.2 to 47.5 µg/L. The method was sensitive, reproducible and simple enough to permit the reliable routine analysis of anions in HF solution used in the process of producing semiconductors.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2008년도 춘계학술대회 논문집
• /
• pp.479-482
• /
• 2008

Since late of 2000, KIER has developed a novel pyrolysis process for production of fuel oils from polymer wastes. It could have been possible due to large-scale funding of the Resource Recycling R&D Center. The target was to develop an uncatalyzed, continuous and automatic process producing oils that can be used as a fuel for small-scale industrial boilers. The process development has proceeded in three stages bench-scale unit, pilot plant and demonstration plant. As a result, the demonstration plant having capacity of 3,000 tons/year has been constructed and is currently under test operation for optimization of operation conditions. The process consisted of four parts ; feeding system, cracking reactor, refining system and others. Raw materials were pretreated via shredding and classifying to remove minerals, water, etc. There were 3 kind of products, oils(80%), gas(15%), carbonic residue(5%). The main products i.e. oils were gasoline and diesel. The calorific value of gas has been found to be about 18,000kcal/$m^3$ which is similar to petroleum gas and shows that it could be used as a process fuel. Key technologies adopted in the process are 1) Recirculation of feed for rapid melting and enhancement of fluidity for automatic control of system, 2) Tubular reactor specially-designed for heavy heat flux and prevention of coking, 3)Recirculation of heavy fraction for prevention of wax formation, and 4) continuous removal & re-reaction of sludge for high yield of main product (oil) and minimization of residue. The advantages of the process are full automation, continuous operation, no requirement of catalyst, minimization of coking and sludge problems, maximizing the product(fuel oil) yield and purity, low initial investment and operation costs and environment- friendly process. In this presentation, background of pyrolysis technology development, the details of KIER pyrolysis process flow, key technologies and the performances of the process will be discussed in detail.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.658-663
• /
• 2010

석유자원의 고갈에 따라 전 세계적으로 석유대체자원인 석탄, 천연가스 및 바이오매스로부터 합성 연료 및 화학물질을 제조하기 위한 피셔트롭스 반응에 관한 많은 연구가 이루어지고 있다. 일반적으로 이러한 피셔트롭스 반응은 주로 스케일 업이 비교적 용이한 고정층 반응기를 사용한 기상반응이 적용되고 있으나, 촉매 기공에서의 확산제어 및 왁스의 생성에 따른 촉매의 비활성화 등의 문제점에 기인하여 최근 들어 초임계 유체를 이용한 반응이 많이 연구되고 있다. 본 연구에서는 피셔트롭스 반응에 관한 담지 촉매 및 반응매체에 관한 좀 더 심도 있는 영향을 고찰하기 위해 다양한 담지촉매를 제조하여 피셔트롭스 반응에 관한 기상반응과 초임계 반응을 비교, 고찰하였다.

• 한국추진공학회지
• /
• 제15권3호
• /
• pp.15-21
• /
• 2011

석유자원의 고갈에 따라 전 세계적으로 석유대체자원인 석탄, 천연가스 및 바이오매스로부터 합성연료 및 화학물질을 제조하기 위한 피셔트롭스 반응에 관한 많은 연구가 이루어지고 있다. 일반적으로 이러한 피셔트롭스 반응은 주로 스케일 업이 비교적 용이한 고정층 반응기를 사용한 기상반응이 적용되고 있으나, 촉매 기공에서의 확산제어 및 왁스의 생성에 따른 촉매의 비활성화 등의 문제점에 기인하여 최근 들어 초임계 유체를 이용한 반응이 많이 연구되고 있다. 본 연구에서는 피셔트롭스 반응에 관한 담지 촉매 및 반응매체에 관한 좀 더 심도 있는 영향을 고찰하기 위해 다양한 담지촉매를 제조하여 피셔트롭스 반응에 관한 기상반응과 초임계 반응을 비교, 검토하였다.

• Restorative Dentistry and Endodontics
• /
• 제49권2호
• /
• pp.12.1-12.10
• /
• 2024

Objectives: This study evaluated the impact of different methods of irrigant agitation on smear layer removal in the apical third of curved mesial canals of 3 dimensionally (D) printed mandibular molars. Materials and Methods: Sixty 3D-printed mandibular second molars were used, presenting a 70° curvature and a Vertucci type II configuration in the mesial root. A round cavity was cut 2 mm from the apex using a trephine of 2 mm in diameter, 60 bovine dentin disks were made, and a smear layer was formed. The dentin disks had the adaptation checked in the apical third of the teeth with wax. The dentin disks were evaluated in environmental scanning electron microscope before and after the following irrigant agitation methods: G1(PIK Ultrasonic Tip), G2 (Passive Ultrasonic Irrigation with Irrisonic- PUI), G3 (Easy Clean), G4 (HBW Ultrasonic Tip), G5 (Ultramint X Ultrasonic tip), and G6 (conventional irrigation-CI) (n = 10). All groups were irrigated with 2.5% sodium hypochlorite and 17% ethylenediaminetetraacetic acid. Results: All dentin disks were 100% covered by the smear layer before treatment, and all groups significantly reduced the percentage of the smear layer after treatment. After the irrigation protocols, the Ultra-X group showed the lowest coverage percentage, statistically differing from the conventional, PIK, and HBW groups (p < 0.05). There was no significant difference among Ultramint X, PUI-Irrisonic, and Easy Clean (p > 0.05). None of the agitation methods could remove the smear layer altogether. Conclusions: Ultramint X resulted in the most significant number of completely clean specimens.

• Restorative Dentistry and Endodontics
• /
• 제25권1호
• /
• pp.144-152
• /
• 2000

Intracoronal bleaching is currently disregarded by many clinicians because of the potential consequence of cervical resorption. To prevent this complication it is recommended that intra coronal barrier materials be placed over the root canal obturation and sodium perborate be used with water rather than with hydrogen peroxide. The purpose of this study was to evaluate the amount of the hydrogen peroxide penetration according to the difference in intracanal base materials and sodium perborate preparation. Fifty extracted intact premolars were instrumented, and filled with gutta-percha. And then the outer surface of the teeth was sealed with wax exposing the CEJ. The prepared teeth were placed in plastic tubes containing 1.5ml distilled water with their entire root submerged into the solution, The teeth were divided into the following five groups. In the first two groups gutta-percha was removed without placement of barrier, and then water or superoxole(30% $H_2O_2$) with sodium perborate were used respectively for bleaching. In the other three groups, after removal of gutta-percha, an intracanal isolating barrier(ZPC, IRM, Fuji II LC) was placed and then bleached with sodium perborate and superoxole. The bleaching procedure was performed 4 times with 1 week interval. The results were as follows : 1. All the groups showed a tendency of increasing penetration amount with increasing treatment times(P<0.05). 2. After the 1st and 2nd treatments, there was no significant difference in microleakage among the groups. 3. After the 3rd bleaching with superoxole and sodium perborate, there was no significant difference in microleakage between gutta-percha alone group and gutta-percha with ZPC, Fuji II LC barrier group. But significant difference was found between IRM barrier group and other groups(P<0.01). 4. After the 4th bleaching with superoxole and sodium perborate, there was no significant difference between gutta-percha alone group and gutta-percha with barrier groups. 5. After the 4th treatment, the group bleached with sodium perborate and water without barrier showed lower hydrogen peroxide penetration than that of other groups(P<0.01).

• 대한치과보철학회지
• /
• 제59권1호
• /
• pp.79-87
• /
• 2021

구강 스캐너를 이용한 디지털 인상과 CAD-CAM (Computer-aided design-computeraided manufacturing) 기술은 점차 발전하고 있다. 전통적인 인상 채득, 작업모형의 제작, 왁스 납형 제작 및 주조의 복잡한 과정이 단축되었으며 환자의 방문 횟수도 줄일 수 있게 되었다. 구강 스캐너 기술의 발전으로 디지털 인상의 정밀도와 정확성이 향상되었으며, 그 적응증은 보다 광범위한 부위의 고정성 치과보철물의 수복으로 점차 확대되어지고 있다. 본 증례 보고에서는 광범위한 부위의 고정성 임플란트 보철물의 수복을 위하여, 컴퓨터로 계획하고 가이드 수술용 템플레이트로 완전히 가이드된 수술을 하고, 즉시/조기 임플란트 보철물을 장착하였으며, 임시 보철물에서 최종 보철물로 전환하는 과정에서 구강스캐너의 지대주중첩 알고리즘을 활용하였다. 임플란트 수술 당일 획득한 구강스캔으로 맞춤형 지대주를 포함한 임시 보철물을 제작하여 활용하였으며, 최종 보철물은 임시 보철물에서의 맞춤형 지대주를 낀 채로 구강스캔하여 제작되었다. 이 과정에서 임시 보철물 장착 전에 미리 스캔해서 라이브러리화한 맞춤형 지대주 데이터를 구강스캐너 소프트웨어 '지대주 자동중첩 기능'으로 최종 디지털 인상에 자동적으로 매칭하였고, 치은연하마진인 부분도 지대주를 탈거하지 않고, 치은압배사 없이 정밀하게 획득할 수 있었다. 구강스캐너와 소프트웨어의 다양한 기술을 응용하여 임플란트 치료 과정을 디지털 워크플로우로 변화시킴으로써, 환자 불편감 및 치료 시간을 단축하였으며, 환자와 술자에게 모두 이롭고 예지성 있는 치료가 가능하였다.