• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.61 no.1
• /
• pp.1-4
• /
• 2012

In this paper, the planar type modified folded loop antennas for S-DMB band is proposed. The proposed antenna consisted of opened center of a conventional closed loop and folded terminal of microstrip line to inside loop antenna. The sizes proposed antenna was minimized by folding the terminal of the loop. Also, It was minimized reactance value by increasing capacitances between coupled microstrip line. Therefore the proposed antennas compacted about 20% than a conventional loop antenna and increased efficiency of antenna. The proposed antennas got an omni-directional pattern, the antenna gain was 3.67 [dBi] and the bandwidth was 900 MHz (2.6-3.56 GHz) with VSWR${\leq}$2 from the simulated and the measured results. The frequency utilization coefficient was 29.9 %. These properties could satisfy the S-DMB band.

• ETRI Journal
• /
• v.41 no.2
• /
• pp.262-269
• /
• 2019

This paper introduces a low-cost, high-performance mmWave antenna array module at 77 GHz. Conventional waveguide transitions have been replaced by 3D CPW-microstrip transitions which are much simpler to realize. They are compatible with low-cost substrate fabrication processes, allowing easy integration of ICs in 3D multi-chip modules. An antenna array is designed and implemented using multilayer coupled-fed patch antenna technology. The proposed $16{\times}16$ array antenna has a fractional bandwidth of 8.4% (6.5 GHz) and a 23.6-dBi realized gain at 77 GHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.1 s.116
• /
• pp.7-14
• /
• 2007

In this paper, the scan characteristics of phased array antenna consisted of rectangular open-ended waveguide with a triangular grid are investigated. An infinite array structure is analyzed by numerically solving the integral equation for the electric field over the waveguide aperture using waveguide mode function and Floquet mode function. Next, SEP(Scan Element Pattern) and SI(Scan Impedance) characteristics are simulated by CST's MWS(Microwave Studio) and Ansoft's HFSS(High Frequency Structure Simulator) for the finite and infinite array structures. Also, validity of these approaches is verified by comparing the calculated and simulated results with the measured ones for an $8{\times}8$ subarray. Within 10.5 % fractional bandwidth in the X-band, the fabricated subarray showed the flat gain characteristic in the scan range of ${\pm}45^{\circ}C$ in the E-plane(azimuth) and ${\pm}20^{\circ}C$ in the H-plane(elevation), and also showed the return loss characteristic of less than -10 dB.

• Proceedings of the Korea Electromagnetic Engineering Society Conference
• /
• 2000.11a
• /
• pp.416-419
• /
• 2000

A narrow slot in the broad wall of a rectangular waveguide is analysed using a Spatial Network Method[1] which takes account of the waveguide wall thickness. In essence, SNM is used to solve arbitrary shape and materials constant, derived from maxwell's equations to find the tangential electric fields on the upper and lower surfaces of the slot. In this paper, applying to the offset and length[2] which yield a zero equivalent shunt susceptance, analysing single and 4 array slot antenna. The current of the transient analysis shows each the times. Analysed result of SNM is verified by the method of moment and HFSS.

• Proceedings of the KIEE Conference
• /
• 2000.11c
• /
• pp.591-593
• /
• 2000

A narrow slot in the broad wall of a rectangular waveguide is analysed using a Spatial Network Method[1] which takes account of the waveguide wall thickness. In essence, SNM is used to solve arbitrary shape and materials constant, derived from maxwell's equations to find the tangential electric fields on the upper and lower surfaces of the slot. In this paper, applying to the offset and length[2] which yield a zero equivalent shunt susceptance, analysing single and 4 array slot antenna. The current of the transient analysis shows each the times. Analysed result of SNM is verified by the method of moment and HFSS.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.1
• /
• pp.53-59
• /
• 2002

In this paper, we present design results for an orthomode transducer(OMT) to be used in multi-band antenna feeds. The OMT is realized in the form of a tapered square waveguide, where 18-20 GHz ports are placed in the taper region normal to the waveguide axis, while 30-45 GHz ports are placed in line with the waveguide axis. The reflection coefficient of each port is designed to be less than 20 dB, while the isolation between ports are greater than 15 dB. Thin septa are placed in side ports to reduce the effect of side ports on the return loss of the in-line port. The commercial software HFSS？ is used to design the whole structure.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.3
• /
• pp.422-428
• /
• 2015

A 2.45GHz microwave plasma source with a linear antenna has been developed for low temperature large scale deposition processing. Microwave power is transmitted through WR340 waveguide and a copper rod, linear antenna, is located in a quartz tube. The power matching is effectively achieved by a linear antenna is located at ${\lambda}_g/4$ or $3{\lambda}_g/4$ from the end of WR340 waveguide. The Ar plasma was generated along the surface of quartz tube and a clear standing wave pattern with nearly 10cm wavelength was observed at Ar pressure of 200mTorr and 200W input power. The electron density and electron temperature were investigated by using the electrostatic probe. The electron density and electron temperature were highly measured near the surface of quartz tube. Ar plasma density along the quartz tube is mostly uniform despite standing wave set-up and antenna of long length. A uniform temperature was measured at 10~40cm distance from the end quartz tube and 5cm distance from the surface of quartz tube.

• Journal of IKEEE
• /
• v.15 no.4
• /
• pp.299-304
• /
• 2011

In this paper, the circular polarized horn antenna composed of circular polarizer and impedance transformer is designed, and fabricated. For the circular polarizer, two types of the polarizer are designed and the electrical performance of them is compared; rectangular waveguide polarizer with $45^{\circ}$-inclined dielectric slab and oval shaped one. Straight type mode converter has a stepped impedance structure and plays a role of converting waveguide TE mode into coaxial TEM mode, and the proposed antenna is designed to directly connect with active components using the feed-through in the input port of the mode converter. Fabricated antenna has the wideband performance, VSWR<1.5 and Axial ratio < 1.0dB, ranging from 30.085 to 30.885 GHz, and the antenna gain is 6.7~7.0 dBi.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.7
• /
• pp.778-785
• /
• 2010

The folded monopole antenna for applying mobile communications equipment and wireless devices is presented in this paper. By using the coplanar waveguide feed the operating bandwidth has improved. In addition, each individual resonant elements has occurred different capacitance through asymmetrical left and right ground planes; therefore, the bandwidth has kept and the impedance matching has stabilized. By measurement results, the impedance bandwidth under VSWR< 2.5:1 are $824{\sim}890$ MHz and the $1,500{\sim}2,170$ MHz, also radiation patterns has omni-directional characteristics. The maximum gains of the proposed antenna are 5.52, 0.64, 3.00, 0.94 and 1.85 dBi at 850, 1,575, 1,790, 1,930 and 2,050 MHz respectively. The proposed antenna will be adapted to the internal antenna of the mobile communication devices.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.22 no.11
• /
• pp.1518-1523
• /
• 2018

A method for designing a DDQYA fed by a CPW is proposed in this paper. The proposed CPW-fed DDQYA consists of two series-connected strip dipoles, a ground reflector, and a strip-pair director. Instead of the conventional microstrip feed line in which the signal line is located on the substrate opposite to the antenna, a CPW is used because CPW is located on the same side with the antenna, and so the fabrication is easy. The strip-pair director is composed of two horizontally-separated strips, and it is added above the second dipole to enhance the gain in the high frequency region. A prototype of the proposed CPW-fed DDQYA is fabricated on an FR4 substrate. The fabricated antenna has a frequency band of 1.66-3.38 GHz(68.3%) for a voltage standing wave ratio < 2, and measured gain ranges 5.0-7.3 dBi over a frequency band of 1.60-2.90 GHz.