• Journal of KSNVE
• /
• v.6 no.5
• /
• pp.671-677
• /
• 1996

This paper presents the analytical method for predicting turbulence- induced noise in the multilayered cylinder composed of an outer hose, an inner fluid and an internal core. It is assumed that an infinite axisymmetric cylinder is located horizontally in water with free stream velocity and the turbulent boundary layer (TBL) surrounding the outer hose is fully developed and homogeneous. The transfer function at the core surface due to the propagation of the pressure fluctuation within the TBL is formulated using the linearized Navier-Stockes equation for solid and fluid. In the estimation of the energy spectrum of wall pressure fluctuation, the empirical formula proposed by Strawderman based on the Corcos model is used. A general algorithm for the calculation of the pressure level at the surface of a core, that is, turbulence- induced noise, is presented. Through the detailed numerical simulation, it is found that the major noise mechanism is the propagation of the bulge wave along hose.

• Proceedings of the Korean Society of Soil and Groundwater Environment Conference
• /
• 2000.05a
• /
• pp.37-40
• /
• 2000

Acoustically enhanced soil flushing method is a newly developed in-situ remediation technique. However, there has not been an analytical method that can be used to evaluate the effectiveness of ultrasonic wave under different conditions. This study was undertaken to investigate the degree of enhancement in contaminant removal due to ultrasonic energy on the soil flushing method. The test conditions included different levels of ultrasonic power and hydraulic gradient. The test soils were Ottawa sand, a fine aggregate, and a natural soil, and the surrogate contaminant was a Crisco Vegetable Oil. The test results showed that sonication could increase contaminant removal significantly. Increasing sonication power increased pollutant removal. The faster the flow is, the smaller the degree of enhancement will be. The pollutants in dense soils are more difficult to be removed than in loose soils.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.5 no.4
• /
• pp.369-383
• /
• 1993

An amended form of radiation stress is presented in the present model and the existence of the surface advection terms is verified through comparisons with wave energy equation. The model yields circulation patterns in both cross-shore and longshore directions on the plane beach slope. Comparison with laboratory experiments showed good agreements. Finally, a quasi-three dimensional model suitable for the entire nearshore zone is developed by linking the depth-integrated properties with vertical profiles.

• Journal of Engineering Education Research
• /
• v.15 no.5
• /
• pp.36-41
• /
• 2012

Student members from The University of Tokushima worked voluntarily at the science school for elementary school children and high school students under the support of Japan Science and Technology Agency. The teaching classes for the science school were held in 2010 as follows: (1) Science handicraft class for children on "Wonder in light, sound, temperature and force", (2) Family Science School for children and parents on "Measurement of length, temperature, weight and energy", (3) "Tatara steel making" for high school students, (4) "Wave motion in strings" for high school students. This paper describes how the students prepared the teaching materials and what they obtained from the teaching activities.

• The Journal of Korean Society for Radiation Therapy
• /
• v.2 no.1
• /
• pp.23-29
• /
• 1987

The general features and measured results of the 143cm, variable-energy, three sector-focused MC-50 cyclotron installed at Korea Cancer Center Hospital are described. The MC-50 cyclotron is designed to produce beams of protons, deuterons, He-3 and alpha particles of maximum energies 50MeV, 25MeV, 66MeV and 50MeV respectively to be used for neutron therapy and radioisotope production. The azimuthal field variation is produced by three sets of spiral ridges having a maximum spiral angle of $55^{\circ}$. The RF system, a two-dee quarter-wave system is designed to provide a continuously variable frequency from 15.5 to 26.8 MHz. The first external beam was obtained in January 1986. Subsequent internal ana external beam studies with protons and alphas show a well-behaved beam through the whole beam transport system.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.4
• /
• pp.683-692
• /
• 2007

An inverter driven induction motor has more superior dynamic characteristic than sine wave driven induction motor. But it has a problem with shaft voltage and bearing current in drive-motor system. This paper presents the analysis of bearing current in inverter-fed induction motor. The proposed method is based on using numerical method (FEM) to derive parasitic parameters in motor. Using the electric field analysis with FEM, the stored energy in dielectric materials of the motor can be calculated and the parasitic capacitances are obtained. Then we compared the proposed method with a conventional method in variable frequency and load conditions. From the comparision of simulation and experiment result, we confirmed that the proposed method is valid.

• Journal of the Korean Society of Safety
• /
• v.13 no.2
• /
• pp.3-12
• /
• 1998

Polymer materials have been used offensively as construction materials for automobiles, ships, and airplanes in recent years, and their impact resistance has been obliged to be examined. In the present study, a dropped load and a specimen, equipped with high responsible strain gauges respectively, were dropped and then the changes of load and absorption energy with time were observed. It was found that the waveforms for dropped weight coincided with output signal wave for specimen during the destruction test. Based on this experimental result, three disc type of specimens with different compositions were prepared and examined. This instrumented impact test method showed that each specimen can be distinguished from each other better than conventional tests and is expected to contribute to assess test results of impact resistance for some materials under development.

• Ocean Systems Engineering
• /
• v.6 no.2
• /
• pp.203-216
• /
• 2016

Over recent years the offshore wind turbines are becoming more feasible solution to the energy problem, which is crucial for Egypt. In this article a three floating support structure, tension leg platform types (TLP), for 5-MW wind turbine have been considered. The dynamic behavior of a triangular, square, and pentagon TLP configurations under multi-directional regular and random waves have been investigated. The environmental loads have been considered according to the Egyptian Metrological Authority records in northern Red sea zone. The dynamic analysis were carried out using ANSYS-AQWA a finite element analysis software, FAST a wind turbine dynamic software, and MATLAB software. Investigation results give a better understanding of dynamical behavior and stability of the floating wind turbines. Results include time history, Power Spectrum densities (PSD's), and plan stability for all configurations.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.11a
• /
• pp.922-925
• /
• 2011

Smoothed Particle Hydrodynamics (SPH) is a Lagrangian method widely used for the modeling fluid flows. Simulations of explosions require, besides the hydrodynamic equations, a realistic equation of state, an energy source term, and a set of chemical kinetic equations to follow the composition changes of the gas during the explosion. The performance of the hydrodynamic equations is investigated in the framework of the Sedov-Taylor blast-wave. The implementation of chemical kinetic equations and equation of state is studied with 1D detonation of TNT slab. Our results are compared to those from analytical and experimental studies.

• Structural Engineering and Mechanics
• /
• v.3 no.4
• /
• pp.391-410
• /
• 1995

The application of adaptive finite element method to dynamic problems is investigated. Both the kinetic and strain energy errors induced by space and time discretization were estimated in a consistent manner and controlled by the simultaneous use of the adaptive mesh generation and the automatic time stepping. Also an optimal ratio of spatial discretization error to temporal discretization error was discussed. In this study it was found that the best performance can be obtained when the specified spatial and temporal discretization errors have the same value. Numerical examples are carried out to verify the performance of the procedure.