• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.41 no.8
• /
• pp.93-97
• /
• 2004

Since powerline for powerline communications (PLC) is designed for supplying electric power using 60 Hz wave, they will have different electrical behaviors for high data rate PLC whose bandwidth is allocated between 1 MHz and 30 MHz. Thus, it is necessary to investigate the different properties in this frequency bandwidth for the high data rate PLC. In this paper, low voltage (220V) powerline impedance for indoor high data rate PLC in between 1 MHz and 30 MHz is measured. For measurement a low voltage coupling unit is made and a vector network analyzer is used. A T-equivalent circuit of the low voltage coupling unit is obtained and then powerline impedance is derived by measuring the reflection coefficient of the total powerline network. With the method proposed, impedance is measured in case of a general korean apartment and its property is analyzed. Measurement shows that the average impedance is about 100Ω.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.11 no.3
• /
• pp.388-402
• /
• 2000

The radiation characteristics of leaky antenna from the dielectric-coated conducting cylinder with periodic corrugation are investigated theoretically for the infinite and finite periodic structures. For the infinite periodic structure, mode-matching method is applied. The integral equation is derived for the finite periodic structure by use of the Fourier transform and mode expansion and a simultaneous linear equation is obtained. The influences of the corrugation slot width, corrugation depth, dielectric thickness, cylinder radius, and finite corrugation number on the radiation characteristics (leakage constant, phase constant, and radiation pattern) are investigated. The results of the finite periodic corrugations are compared with those of the infinite extent structure and good agreement is found. To reduce high side lobe levels of the uniform finite periodic structure, tapering process on the beginning and end section of antenna and nonuniform quasi-period slot arrays are considered. Especially, for the corrugation period, width and depth used for a corrugated surface wave antenna, through the proper tapering process, end-fire radiation pattern with reduced side lobe levels is given.

• Wind and Structures
• /
• v.24 no.1
• /
• pp.1-24
• /
• 2017

Wind environment in urban residential areas is an important index to consider when evaluating the living environment. However, due to the complexity of the flow field in residential areas, it is difficult to specify the correct inflow boundary conditions in the large eddy simulation (LES). In this paper, the weighted amplitude wave superposition (WAWS) is adopted to simulate the fluctuating velocity data, which satisfies the desired target wind field. The fluctuating velocity data are given to the inlet boundary of the LES by developing an UDF script, which is implemented into the FLUENT. Then, two numerical models - the empty numerical wind tunnel model and the numerical wind tunnel model with spires and roughness elements are established based on the wind tunnel experiment to verify the present method. Finally, the turbulence generation approach presented in this paper is used to carry out a numerical simulation on the wind environment in an urban residential area in Lisbon. The computational results are compared with the wind tunnel experimental data, showing that the numerical results in the LES have a good agreement with the experimental results, and the simulated flow field with the inlet fluctuations can generate a reasonable turbulent wind field. It also shows that strong wind velocities and turbulent kinetic energy occur at the passageways, which may affect the comfort of people in the residential neighborhood, and the small wind velocities and vortexes appear at the leeward corners of buildings, which may affect the spreading of the pollutants.

• Journal of the Korean Society of Costume
• /
• v.62 no.4
• /
• pp.1-14
• /
• 2012

Ever since the year 2000, Korea's musical markets has invited famous overseas license performances and have therefore cooperated with staffs working overseas in regards to stage costumes. This study aims to suggest the methodology of the stage costume making process according to the present advanced production system of Korea's musical market. The researcher participated in the stage costume making work of 'Chicago' as a costume supervisor. It took place at the Opera House of Seongnam Art Center from January 10, 2010 to February 28, 2010. Furthermore, there was significance in reinforcing academic values and implementing practical making process of stage-costumes based on the actual field work. The method of this research was carried out through a theoretical research and a case study that focused on empirical research. As for the research scope, it was limited to the actual stage-costumes that the researcher fully engaged with as a costume supervisor of the musical 'Chicago.' The results of this study were as follows. The stage costume making process of the musical 'Chicago' was categorized according to the classification of production system in the performance. For pre-production, it was divided according to the information of the actor and the analysis of the bible. Rehearsal period was divided according to the product clothes and fitting. Production week & preview were divided according to the changeover of clothes and the arrangement of dressers. The Run was divided according to the inspection of the situation concerning clothes in general during the performance. Post-Production Period was divided according to the collection of clothes and the implemented database. This study eventually suggested appropriate stage-costume making processes for the costumes making environment according to the expansion of overseas license musical market. However, it has a limitation of the research scope to the musical 'Chicago.' The creative performances of the domestic version are planned in diverse forms and come to abroad animate by the Korean Wave. Therefore, the field of stage-costume is necessary for the establishment of practical schemes of the system and copyright in accordance with the environment.

• Journal of Advanced Navigation Technology
• /
• v.22 no.5
• /
• pp.436-441
• /
• 2018

In this paper, a design method for a compact double dipole quasi-Yagi antenna with a V-shaped ground plane operating in dual bands including 2.45 GHz and 5 GHz wireless LAN frequency bands is studied. First, a quasi-Yagi antenna operating in the 2.45 GHz band is designed, and a V-shaped ground plane is used instead of a conventional strip ground plane to reduce the length of the antenna. A second dipole is connected to the dipole driver of the quasi-Yagi antenna for 2.45 GHz band and a director is appended for 5 GHz band operation. A prototype of the proposed dual-band antenna operating at 2.45 GHz WLAN band and 4.57-7.11 GHz band is fabricated on an FR4 substrate with a dimension of 40 mm by 55 mm. Fabricated antenna shows frequency bands of 2.33-2.75 GHz and 4.38-7.5 GHz for a voltage standing wave ratio less than 2. Measured gain remains more than 4 dBi in both bands.

• Journal of the Korean Institute of Navigation
• /
• v.25 no.1
• /
• pp.53-60
• /
• 2001

This paper presents the fabrication of the LNA which is operating at 2.13 ~ 2.16 GHz for IMT-2000 front-end receiver using series feedback and resistive decoupling circuit. Series feedback added to the source lead of a GaAs FET keeps the low noise characteristics and drops the input reflection coefficient of a low noise amplifier simultaneously. Also, it increases the stability of the LNA. Resistive decoupling circuit is suitable for input stage matching because a signal at low frequency is dissipated by a resistor in the matching network. The amplifier consists of GaAs FET ATF-10136 for low noise stage and VNA-25 which is internally matched MMIC for high gain stage. The amplifier is fabricated with both the RF circuits and self bias circuit on the Teflon substrate with 3.5 permittivity. The measured results of the LNA which is fabricated using the above design technique are presented more than 30 dB in gain, PldB 17 dB and less than 0.7 dB in noise figure, 1.5 in inputㆍoutput SWR(Standing Wave Ratio).

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.48 no.10
• /
• pp.745-752
• /
• 2020

A numerical study was carried out to evaluate the aerodynamic characteristics of the supersonic grid fins installed on SpaceX Falcon 9. The unit-grid-fin concept was utilized for more efficient and simpler 3-D steady flow calculations. Pre- and post-correction processes that accounted the interference effects by the angle of attack of the missile, the influences of the outer frame of the grid fin and the connecting rods were improved in the study, and it was demonstrated that the present correction method was more accurate as compared to previous studies. Finally, the present approach was applied to evaluate the aerodynamic characteristics in transonic/supersonic flights of SpaceX Falcon 9 with various angle of attacks.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.5
• /
• pp.906-912
• /
• 2017

In this paper, we studied a design method for a broadband 3-element quasi-Yagi antenna (QYA) for indoor digital television (DTV) reception. The proposed QYA employs a novel balun between a microstrip (MS) line and a coplanar strip (CPS) line feeding the driver dipole. The proposed balun is constructed by connecting the end of MS line to CPS line through a shorting pin, and the CPS and ground reflector are connected through a circular ring-type conductor. An antenna, as an design example for the proposed antenna, is designed for the operation in the frequency band of 470-806 MHz for terrestrial DTV. The antenna fabricated on an FR4 substrate with a size of $270mm{\times}150mm$ showed a good performance such as a frequency band of 470-820 MHz for a voltage standing wave ratio < 2, a gain > 4.0 dBi, and a front-to-back ratio > 8.4 dB over the DTV frequency band.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.3
• /
• pp.197-203
• /
• 2004

New lithography techniques are employed for the patterning of arbitrary shapes in nanometer scale. When, in the photolithography, the electromagnetic waves such as UV and X-ray are incident on the mask patterned in nanometer scale, the diffraction effect is unavoidable and degrades images of the mask imprinted on wafer. Only a convex lens is well-known Fourier transformer. It is possible to make the mask Fourier-transformed with the convex lens, even though the size of pattern on the mask is very large compared to the wavelength of electromagnetic wave. If the mask, modified according to new technique described in this paper, was placed at the front of the lens and was illuminated with laser beam, the nanometer-size patterns are only formed on the plane called Fourier transform plane. The new method presented here is quite simple setup and comparable with present and next generation lithographies such as UV/EUV photolithograpy and electron projection lithography when compared in attainable minimum linewidth. In this paper, we showed our theoretical research work in the field of Fourier optics, . In the near future, we are going to verify this theoretical work by experiments.

• Journal of Korean Society of Transportation
• /
• v.33 no.4
• /
• pp.405-416
• /
• 2015

This paper developed a method analyze drivers' response characteristics using spectral analysis with car following data. Cross-correlation function and cross spectrum are produced by Fourier transform from speed fluctuations of leading vehicle and following vehicle during the designated time ${\tau}$. Based on the analysis data, a process to calculate the reaction time and stimulus-adaption index of following vehicle was developed and 170 cases of field data was applied. It was reported average of 0.654 and 2.091 seconds of stimulus-adaption index and reaction time respectively. In conclusion, the developed indexes might contribute to enhance vehicle control of autonomous vehicle more efficient and safer.