• Journal of Korean Society on Water Environment
• /
• v.30 no.2
• /
• pp.206-211
• /
• 2014

This study was done to find chemicals adequate to control alkalinity and hardness in order to reduce dissolved phosphorus in water bodies like rivers and lakes. Five chemicals were selected for the study: calcite, lime, dolomite, magnesite, and gypsum. Data were obtained from the calculations with MINTEQ model as a function of dosage variations of each chemical. Findings are as follows: Three out of the five chemicals are found to be effective in reducing the dissolved phosphorus, i.e., calcite, lime, and dolomite. Calcite and dolomite are able to lower the phosphorus concentration up to one thousandth fold whereas lime does one hundred thousandths fold. In viewpoint of pH variation, both calcite and dolomite seem to be safe since the pH does not increase over 8.3 even in case of overdose. In the same circumstance, with lime the pH increases beyond 9 which is considered to be the highest pH level for the protection of water ecosystem. Nevertheless it is recommendable to use lime in case where there are some difficulties in water quality control due to algae blooms.

• Journal of Korean Society of Water and Wastewater
• /
• v.29 no.3
• /
• pp.381-393
• /
• 2015

This study is carried out in order to propose a drought risk assessment methodology. This methodology is required to deal with practical questions that a variety of stakeholder often raise in the course of discussions on mitigation measures. With a focus on the socioeconomic aspect of drought, more particularly, residents' hardship from water scarcity, it suggests basic concepts and a system of methods in order to assess hazard, exposure, vulnerability and risk. The case study shows a considerable possibility of the methodology in evaluating potential levels of damages in a certain area, in identifying the boundary of districts where risk is disproportionately concentrated, and also in understanding the underlying risk factors of those districts. The authors think that the proposed methodology is able to offer risk information in terms of socioeconomic damages, and therefore contribute to reducing information gaps that policy-makers are currently encountered with.

• Journal of the Korea Institute of Building Construction
• /
• v.8 no.5
• /
• pp.59-65
• /
• 2008

In the evaluation method of KS on the activity factor of fly ash, same amount of cement should be replaced with fly ash. Therefore, contradictory effects on concrete strength exist, i. e. strength decease due to low content of cement and strength increase of strength due to filling-pore-function of fly ash. European Committee for Standardization (CEN) specifies the method 1 to 4. adding fly ash without reducing the content of cement, for the evaluation method on activity factor of fly ash. This study investigates the applicability of the method 2 of CEN to mix design of concrete. The followings are derived ; There is a key ratio of f)y ash mixing which enhances the incremental ratio of mixing water to improve fluidity of mortar. The incremental ratio of mixing water is maximized about 11% ratio of fly ash mixing. Compressive strength most slightly increases at that ratio of fly ash mixing. Activity factor of fly ash increases as water-cement ratio becomes low and contents of fly ash becomes high. Moreover, quality of fly ash and condition of mix design affect the applicable amount of fly ash and available range of water-cement ratio. However, this method has some problems for practical purpose because activity factors of fly ash for some cases are over 1.0. Further research should be conducted to develop more useful method of evaluating activity factor of fly ash.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.8 no.4
• /
• pp.17-23
• /
• 2012

Due to reinforcement of international environment regulation and high oil prices, interest in renewable energy is growing. Countries participating in UNFCCC are continuously putting efforts in reducing greenhouse gas after enforcing Kyoto Protocol into effect on Feb, 2005. Energy used in buildings, which relies heavily on fossil fuel accounts for about 24% of total energy consumption. In this study, air, geothermal and water source heat pump systems for an 322 $m^2$ auditorium in an office building is simulated using TRNSYS version 17 for comparing energy consumptions. The results show that energy consumptions of air, geothermal and water source heat pumps are 14,485, 10,249, and 10,405 kWh, respectively. Annual equal payments which consider both initial and running costs become 5,734,521, 6,403,257 and 5,596,058 Won. Thus, water source heat pump is the best economical choice.

• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.760-767
• /
• 2000

Recently, the protection of construction is demanded with environmental pollution. These protect modes are use of concrete admixture, coat of protective polymer and impregnate of surface with chemicals etc. The most widely used impregnation is economical and effective. The define of Impregnation for construction protect is reacted in and consolidated substrate after absorbed. The impregnation agents are Polyesters, Acrylic monomers, Epoxy and Silicone derivatives. Commonly, because the Silane has good water repellency and environmental advantages that it widely used to water proofing agents, dampproofing agents and absorption reducer for concrete of bridges. When application of Silane, it occurs pollution and harmfulness as included organic solvent. The manufactures have tired to emulsification of Silane for the reducing of the defects. The Silane emulsion is vary unstable and does not stored long periods, and it is diminished in good properties with internal reaction. In this study we tried to emulsification of Silane for effectiveness improvement and reduce pollution and hazard and discussed properties variation of emulsion. The Silane emulsions are achieved emulsifying with W/O and O/W type surfactants. It used 0.24% PVA as protective colloid and stable phase is creamy. The creamy Silane emulsion performance as the penetration depth and water absorption rate are above 4 mm and below 0.1. It stable about 6 month at room temperature.

• Geosystem Engineering
• /
• v.21 no.6
• /
• pp.335-343
• /
• 2018

Alkali-surfactant polymer flooding has become an important technique to improve oil recovery following the development of oil fields while the function of emulsification in enhanced oil recovery is rarely considered in the existing mathematical model for numerical simulation. In this paper, the mechanism of improving the recovery of the emulsification was analyzed in ASP flooding, and a relatively perfect mathematical model with deep filtration-theory was established, in which oil-water volume equation, saturation equation, viscosity equation, and permeability reduction equation are included. The new model is used to simulate the actual block of an oil field; the simulated results of the new model and an old model without considering the emulsification are compared with the actual well history. It is found that new model which is easy to be realized in numerical simulation has a high precision fitting, and the effect of adding oil and decreasing water is obvious. The sensitivity of emulsification was analyzed, and the results show that the water reducing funnel becomes wider and the rate of water cut decreases rapidly with the increase of emulsifying capacity, and then the rate of recovery slows down. The effect of increasing oil and decreasing water is better, and the degree of recovery increases. The emulsification of the ASP flooding is maintained at a moderate level, which corresponds to ${\Phi}=0.2$ in the new model, and the emulsification is applied to realize the general mathematical quantitative description, so as to better guide the oilfield development.

• The Korea Journal of Herbology
• /
• v.38 no.3
• /
• pp.11-18
• /
• 2023

Objectives : This study aimed to investigate the effect of face washing on pore changes in a controlled environment without external condition changes. The research compared the results of water washing, foam cleanser (F/C) washing, and herb cp (cold process) soap washing on pore reduction. Methods : The experiment was conducted using the same water and towel, in the same place, before and 10 minutes after washing. The skin test was performed before and after washing, and three cases of herb cp soap were tested: Ginseng, Liriope platyphylla (LP), and Castanea crenata inner shell (CCIS). A control group was established using water and F/C washing. Results : Water washing and F/C washing showed a similar degree of pore reduction. Men and individuals with complex skin types showed significantly larger pores. LP cp soap showed the greatest significance in pore reduction. Conclusion : This study found that pore shrinking effects were observed regardless of the use of facial cleansers. LP cp soap was found to be the most effective in reducing pore size. It is important to emphasize the importance of face washing for individuals with large pores and combination skin types, especially men.

• Advances in environmental research
• /
• v.12 no.1
• /
• pp.1-15
• /
• 2023

Wastewater of anthropogenic origin is known to harbor various bacteria that are known to be of potential risk to human health and environment. It is of utmost importance to monitor such water sources. Coliforms present in the sewage water samples of municipal sewage treatment plants located at three different places in the South Gujarat region (Surat, Navsari and Vapi) of India were analyzed for their coliforms load as well as tested for their drug resistance. Using cultivation-based techniques microbial load and drug resistance (Amoxicillin, Tetracycline, Ciprofloxacin, Erythromycin, Trimethoprim and Sulphamethoxazole) were analyzed. Water treatment statistically significantly decreased the bacterial load in Vapi and Navsari samples. The optical density of with and without antibiotics of all the three locations was shown to increase significantly after 72 hours. Of all the isolates tested, except isolate 'VA5' (resisted up to 90 ㎍ of Ampicillin) all other isolates resisted 256 ㎍ concentration of antibiotics tested. This study indicates that the sewage water is being contaminated with drugs and/or antibiotics due to industrial and/or anthropogenic activities. Regular monitoring of the water quality is required followed by implementation of environmental laws for reducing the pollutants, that are of human health and environment concern.

• Journal of the Korean Wood Science and Technology
• /
• v.52 no.4
• /
• pp.301-318
• /
• 2024

Contrary to other materials like metals, glass, etc., wood continuously interacts with the environment, increasing and decreasing its moisture content according to the humidity of the air and changing its dimensions by swelling or shrinking. Water diffusion through laminated solid wood is crucial in wood bonding processes. The adhesive layer might block the diffusion if the water vapor diffusion is perpendicular to the bond line. As a result of this blockage, different proportions of deformation appear on the two sides of the bond line, which causes stresses in the bonded assembly. The question arises of how long the bonded structure will keep its integrity due to moisture diffusion blockage, inevitable tensions appearing in the glue line, and how these stresses could be avoided. With cross laminated timber (CLT) solid wood panel production, this question gains new importance. Despite the relevance, only a limited number of publications are available. Comprehensive research would also be necessary considering both the molecular structure and diffusion properties of the adhesive adjusted to the wood species (covering possible substituting wood species, too). Overall, this review serves as a resource for enhancing our understanding of water vapor diffusion through wood adhesive layers and provides insights that have implications for reducing stresses in bonded wood assemblies and the performance of the bonded group over time. Furthermore, identifying knowledge gaps is necessary to establish the basis for investigating the diffusion property of CLT panels.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.11 no.3
• /
• pp.7-12
• /
• 2015

Currently water supply system with water storage is generally applied except for small building such as single-family houses, and water supply system on replacing water storage installed system by direct connecting system has been increasing because of sanitary and energy-saving aspects. The purpose of this study is to evaluate energy-saving and environmental efficiency of direct connecting booster pump system in comparison with the water storage installed system. The architectural condition of the evaluation subject is ten-story apartment house in which sixty households live. To calculate the power consumption of the pump, the volume of water supply was determined from existing data and other data, such as head, efficiency of the pump, was the value used for general application in design office. The power consumption of the water supply pump for one day was 8.5 kWh for direct connecting booster pump system, and 22.5 kWh for water storage installed system, and the former system showed energy savings of 62% compared to the latter system. Reduced power consumption also leads to reduction of $CO_2$ emission. According to the criteria presented in the Korea Energy Management Corporation, reducing the 2,410 kg $CO_2$ emission is possible per year.